fuel LAND ROVER DEFENDER 1999 Manual Online

19FUEL SYSTEM
4
REPAIR ELEMENT - FUEL FILTER
Service repair no - 19.25.07
Remove
1.Release fixings and remove battery cover.
2.Disconnect battery negative lead.
3.Raise rear of vehicle.
WARNING: Support on safety stands.
4.Release fixing and remove fuel filter cover.
5.Clean area around fuel filter.
6.Disconnect multiplug from filter element.
7.Remove fuel filter element.
Refit
8.Clean fuel filter and mating face.
9.Fit new fuel filter element and connect multiplug.
10.Position fuel filter cover and secure with fixing.
11.Remove stand(s) and lower vehicle.
12.Reconnect battery negative lead.
13.Fit and secure battery cover.COOLER - FUEL
Service repair no - 19.25.30
Remove
1.Remove 3 bolts and remove engine acoustic
cover.
2.Remove battery cover.
3.Disconnect battery negative lead.
4.Drain cooling system.See COOLING
SYSTEM, Adjustment.
5.Release 3 clips and disconnect 3 coolant hoses
from fuel cooler.
6.Release 2 fuel hoses from fuel cooler.
CAUTION: Plug the connections.
7.Release vacuum pipe clip from fuel cooler.
8.Remove 4 bolts securing fuel cooler to inlet
manifold and remove cooler.
Refit
9.Clean fuel hose connections.
10.Position fuel cooler to inlet manifold. Apply
Loctite 242 to bolts and tighten to18 Nm (13
lbf.ft).
11.Connect fuel hoses.
12.Connect coolant hoses, secure with clips.
13.Secure vacuum hose to fuel cooler.
14.Refill cooling system.See COOLING SYSTEM,
Adjustment.
15.Fit engine acoustic cover and secure with bolts.
16.Reconnect battery negative lead.
17.Fit battery cover.
ProCarManuals.com

FUEL SYSTEM
5
REPAIR TURBOCHARGER
Service repair no - 19.42.01
Remove
1.Remove battery cover.
2.Disconnect battery negative lead.
3.Remove 3 bolts and remove engine acoustic
cover.
4.Release clip and disconnect breather hose from
camshaft cover.
5.Release clips and disconnect air flow meter from
air filter.
6.Disconnect multiplug from air flow meter.
7.Loosen clip screw and remove air inlet hose
from turbocharger.
8.Remove 3 bolts and remove exhaust manifold
heat shield.
9.Release clip and disconnect vacuum hose from
turbocharger wastegate.
10.Loosen clip screw and release air outlet hose
from turbocharger.
11.Remove turbocharger oil feed banjo bolt and
discard sealing washers.
12.Remove 3 nuts and release exhaust front pipe
from turbocharger and discard gasket.
13.Remove 3 nuts securing turbocharger to exhaust
manifold.
14.Loosen and unscrew turbocharger drain pipe
union from cylinder block.
15.Remove turbocharger and discard gasket.
16.Remove 2 bolts and remove turbocharger oil
drain pipe. Discard gasket.
ProCarManuals.com

19FUEL SYSTEM
6
REPAIR Refit
17.Clean turbocharger and oil drain pipe mating
faces.
18.Using a NEW gasket, fit turbocharger drain pipe
and tighten bolts to10 Nm (7 lbf.ft).
19.Using a new gasket fit turbocharger to exhaust
manifold and tighten nuts to30 Nm (22 lbf. ft).
20.Position oil drain pipe to cylinder block and
tighten union.
21.Using new gasket, align exhaust front pipe and
tighten nuts to30 Nm (22 lbf.ft)
22.Fit banjo bolt to oil feed pipe using new sealing
washers and tighten to25 Nm (18 lbf.ft).
23.Position air outlet hose to turbocharger and
tighten clip screw.
24.Position and secure vacuum hose to
turbocharger wastegate.
25.Position exhaust manifold heat shield and
tighten M6 bolts to9 Nm (7 lbf.ft)and M8 bolt to
25 Nm (18 lbf.ft).
26.Position air inlet hose to turbocharger and
tighten clip screw.
27.Connect air flow meter to air filter and secure
clips.
28.Connect air flow meter multiplug.
29.Connect breather hose and secure clip.
30.Fit engine acoustic cover and secure with bolts.
31.Reconnect battery negative lead.
32.Fit battery cover.FILTER ASSEMBLY - AIR
Service repair no - 19.10.01
Remove
1.Loosen clip screw and release intake hose from
air filter.
2.Release 2 clips securing air flow meter.
3.Release air flow meter from air filter cover and
position aside.
4.Disconnect multiplug from AAP sensor.
5.Release air filter from 3 grommets, remove
assembly and discard’O’ring.
6.Remove 2 screws, remove AAP sensor and
discard’O’ring.
ProCarManuals.com

FUEL SYSTEM
7
REPAIR Refit
7.Clean air flow meter faces.
8.Fit new’O’ring to air filter.
9.Clean AAP sensor.
10.Using new’O’ring, fit AAP sensor and tighten
screws.
11.Position air filter assembly and secure in
grommets.
12.Position air flow meter and secure clips.
13.Position intake hose to air filter and tighten clip
screw.INJECTOR - SET
Service repair no - 19.60.12
Remove
1.Remove cooling fan.See COOLING SYSTEM,
Repair.
2.Remove rocker shaft.See ENGINE , Repair.
3.Position container to catch fuel spillage.
4.Disconnect quick release fuel hose connectors
from fuel connector block on cylinder head and
fuel cooler to drain fuel from cylinder head.
5.Disconnect 5 multiplugs from injectors.
6.Remove Torx bolt securing injector unit to
cylinder head.
ProCarManuals.com

19FUEL SYSTEM
8
REPAIR
7.AssembleLRT-12-154/1to injector unit, screw in
slide hammer and remove injector.
8.UsingLRT-12-154/4,remove and discard
sealing washer.9.Remove and discard’O’ring seal.
10.Rotate engine to align camshaft lobes for access
of injector removal tool.
11.Carry out above procedure to remove the
remaining 4 injectors.
12.Rotate engine manually until each cylinder being
worked on is at TDC, and remove excess fuel
from piston bowl using a syringe.
Refit
13.Clean injector unit and mating faces in cylinder
head.
14.PositionLRT-12-154/2to injector units and fit
new’O’rings.
15.Fit new sealing washers to injector nozzles using
LRT-12-154/3.
16.Fit retainers to injectors, carefully fit injectors
ensuring retainer is located on its dowel and
tighten bolt to32 Nm (24 lbf.ft)
17.Connect multiplug to injector.
18.Repeat above operation for remaining injectors.
19.Connect fuel hoses.
20.New injectors must be programmed using
TestBook.
21.Fit rocker shaft.See ENGINE , Repair.
22.Fit cooling fan.See COOLING SYSTEM,
Repair.
ProCarManuals.com

FUEL SYSTEM
9
REPAIR HEATER PLUGS - SET
Service repair no - 19.60.31
Remove
1.Remove 3 bolts and remove engine acoustic
cover.
2.Remove battery cover.
3.Disconnect battery negative lead.
4.Disconnect 4 heater plug leads.
5.Loosen and remove 4 heater plugs.
Refit
6.Throughly clean heater plugs and seating area
in cylinder head.
7.Apply a suitable anti-seize compound to threads
of heater plugs.
8.Fit heater plugs and tighten to16 Nm (12 lbf. ft)
.
9.Connect heater plug leads.
10.Fit engine acoustic cover.
11.Reconnect battery negative lead.
12.Fit battery cover.INTERCOOLER
Service repair no - 19.42.15
Remove
1.Remove radiator.See COOLING SYSTEM,
Repair.
2.Release clip and remove air hose from
intercooler.
Refit
3.Position air hose to intercooler and secure with
clip.
4.Fit radiator.See COOLING SYSTEM, Repair.
ProCarManuals.com

19FUEL SYSTEM
10
REPAIR POTENTIOMETER - THROTTLE
Service repair no - 19.30.14
Remove
NOTE: The throttle potentiometer is an
integral part of the throttle pedal assembly
and must not be dismantled.
1.With assistance remove 2 nuts and bolts
securing throttle pedal to body.
2.Disconnect multiplug from throttle potentiometer
and remove throttle pedal.
Refit
NOTE: From Vin 607225 a three track
throttle potentiometer was fitted in place
of a two track potentiometer. Three track
potentiometers cannot be fitted to vehicles
previously fitted with two track potentiometers.
Two track potentiometers can be fitted to vehicles
previously fitted with three track potentiometers,
but TestBook must be used to configure the ECM.
3.Connect multiplug to throttle potentiometer.
4.Position throttle pedal assembly, tighten nuts
and bolts to25 Nm (18 lbf.ft).PUMP - FUEL
Service repair no - 19.45.08
Remove
1.Remove fuel tank.See this Section.
2.UsingLRT-19-009remove locking ring from fuel
pump housing.
3.Remove fuel pump from tank and discard
sealing ring.
Refit
4.Clean pump housing and mating face on fuel
tank.
5.Fit seal to pump housing.
6.Fit pump to fuel tank and secure with locking
ring.
7.Fit fuel tank.See this Section.
ProCarManuals.com

FUEL SYSTEM
11
REPAIR REGULATOR - FUEL PRESSURE
Service repair no - 19.45.06
Remove
1.Remove battery cover.
2.Disconnect battery negative lead.
3.Remove 3 bolts and remove engine acoustic
cover.
4.Release hose from fuel cooler.
5.Release fuel hoses from pressure regulator.
CAUTION: Plug the connections.
6.Disconnect multiplug from fuel temperature
sensor.
7.Remove 3 bolts, remove pressure regulator from
cylinder head and collect gasket and’O’ring.
8.Remove fuel filter from cylinder head.
9.Remove fuel temperature sensor and discard
sealing washer.
10.Remove fuel hose and fuel pipe and discard’O’
rings.
Refit
11.Clean fuel pressure regulator, mating face and
fuel filter.
12.Clean fuel pipe unions.
13.Fit fuel pipe and fuel hose to pressure regulator
using new’O’rings.
14.Fit fuel temperature sensor using new sealing
washer and tighten to14 Nm (11 lbf.ft).
15.Fit fuel filter to cylinder head.
16.Using a new gasket and’O’ring position
pressure regulator and tighten bolts to25 Nm
(18 lbf.ft).
17.Connect fuel temperature sensor.
18.Connect fuel hoses to pressure regulator and
fuel cooler.
19.Fit engine acoustic cover.
20.Reconnect battery negative lead.
21.Fit battery cover.
ProCarManuals.com

19FUEL SYSTEM
12
REPAIR FUEL TANK
Service repair no - 19.55.01
Remove
1.Drain fuel tank.See Adjustment.
2.Raise rear of vehicle.
WARNING: Support on safety stands.
Vehicles fitted with tow bar
3.Remove 2 bolts securing support bars to drop
plate.
4.Loosen 2 nuts securing support bars to chassis.All Vehicles
5.Remove 2 nuts securing fuel tank support to rear
chassis member.
6.Remove 2 bolts securing fuel tank support plate
to chassis member.
7.Release clip securing filler hose and release
hose from filler neck.
ProCarManuals.com

FUEL SYSTEM
13
REPAIR
8.Disconnect vent hose from clips on rear chassis
member.
9.Support weight of fuel tank.
10.With assistance, lower fuel tank and remove
support plate.
11.Disconnect multiplug from fuel pump.
12.Noting their fitted position, disconnect 4 fuel
hoses from fuel pump.
13.Release clip and disconnect filler neck breather
from fuel tank.
14.With assistance, lower and remove fuel tank.
15.Remove 2 scrivits securing heat shield remove
heat shield.
16.Release clip securing breather hose to tank and
remove hose.
17.UsingLRT-19-009remove fuel pump locking
ring.
18.Remove fuel pump and discard sealing ring.
ProCarManuals.com