electrical LAND ROVER DISCOVERY 1995 Workshop Manual

ELECTRICAL
13
REPAIR EXTERIOR DRIVING MIRRORS
Service repair no - 76.11.10
Replacing the mirror glass
1.Press the outer end of the glass inwards to its
full extent.
2.Insert the fingers under the inner end of the
glass and pull outwards until the glass is
released from its two retaining clips.
3.Disconnect the two demister leads attached to
the back of the glass unit.
4.To replace the glass, locate the inner end of the
glass in the retaining clip of the housing first.
5.Carefully press the outer end of the glass
inwards until it securely locates in the front
retaining clip.
6.Reset the fine adjustment as required.Complete assembly
Service repair no - 76.11.10
Remove
1.Disconnect battery negative lead.
2.Carefully prise off interior finisher to reveal
retaining plate and securing screws.
3.Disconnect electrical plug.
4.Supporting the mirror assembly remove three
securing screws and retaining plate.
5.Detach mirror assembly from outer door frame.
Refit
6.Reverse removal procedure.
NOTE: To prevent damage to the electrical
lead ensure that it is not pushed down
inside the door casing.

86ELECTRICAL
14
REPAIR REAR DOOR ACTUATOR
Service repair no - 86.26.09
Remove
1.Disconnect battery negative lead.
2.Remove the door pull, trim panel and vapour
protective sheet from the inner door panel.
See
CHASSIS AND BODY, Repair, Rear Door
Trim Panel
3.Disconnect the actuator leads from the door
electrical harness.
4.Remove the two screws securing the actuator
door panel.
5.Manoeuvre the actuator, disconnect the rod from
the link and withdraw the actuator from the door.
Refit
6.Reverse removal procedure.REAR SIDE DOOR ACTUATOR UNITS
Service repair no - 86.26.09
Remove
1.Ensure that the window glass is in the fully
closed position.
2.Disconnect battery negative lead.
3.Remove the door pull, trim panel and plastic
vapour proof barrier.
See CHASSIS AND
BODY, Repair, Rear Side Door - Trim Panel
4.Disconnect the actuator lead from the door
harness at the connector.
5.Note the locations and release the straps
securing the actuator lead to the door casing.
6.Remove the four screws securing the actuator
mounting plate to the door casing.
7.Unhook the operating rod from the actuator link
and withdraw the actuator and mounting plate
from the door.
8.If a new actuator is being fitted remove the
mounting plate from the existing actuator.

ELECTRICAL
15
REPAIR Refit
9.If removed fit the mounting plate to the actuator.
10.Engage the actuator operating rod with hooked
end of the actuator link.
11.Fit the actuator and mounting plate to the door
and loosely secure with the four screws.
12.Set the mounting plate with the screws in the
centre of the slotted holes, then tighten the
screws.
13.Connect the actuator lead to the door harness.
14.Reconnect battery negative lead.
15.With the sill locking button held in position, set
the bellcrank to approximately the position it
would be in if the sill button was depressed to
half of its total movement.
16.At this setting check the electrical operation of
the door lock. Adjust the mounting plate as
necessary to achieve the correct setting. Fully
tighten the securing screws on completion.
17.Refit the vapour barrier.
18.Connect the sill button operating rod to the
bellcrank, hold in position, fit the door trim panel
and the door pull.
BULB REPLACEMENT
For bulb type and rating refer to rating shown on the
bulb or bulb replacement list.
See GENERAL
SPECIFICATION DATA, Information, Bulbs
HEADLIGHT
Service repair no - 86.40.02/13
Remove
1.Rotate three retaining clips 10 degrees, to align
with slots in headlight mounting plate.
2.Withdraw light unit
NOTE: Detach adjustment operating rod
on vehicles fitted with headlight levelling.3.Disconnect electrical multiplugs and remove
headlight unit.
4.Release spring clips and withdraw headlight
bulb.
Key
1. Headlight
2. Retaining clips
3. Bulb
4. Spring clip
5. Cover
6. Bulb sidelight
7. Plug
8. Plug sidelight
Refit
5.Reverse removal procedure.

86ELECTRICAL
16
REPAIR SIDELIGHT BULB
Service repair no - 86.40.33
Remove
1.Remove headlight,
See Headlight
2.Disengage bulb holder by twisting a quarter turn
anti-clockwise.
3.Withdraw bulb from holder.
Refit
4.Reverse removal procedure.FRONT DIRECTION INDICATORS
Service repair no - 86.40.41
Remove
1.Pull spring clips, release from location and lift out
direction indicator unit.
2.Turn bulb holder anti-clockwise to release from
indicator unit.
3.Push and twist the bulb to remove.
Refit
4.Reverse removal procedure. When replacing
light unit, locate the two lugs at the bottom of the
lens before re-engaging spring clips.

ELECTRICAL
17
REPAIR REAR LIGHT UNIT
Service repair no - 86.40.74
Remove
1.Pull out side facing seat or pocket cover.
2.Unscrew fastener and remove access panel.
3.Disconnect wiring harness multi-plug from light
unit.
4.Remove retaining nuts and withdraw light unit
from rear of vehicle.
Key
1. Access panel
2. Multiplug
3. Retaining nut
4. Bulb holder
5. Bulb
Refit
5.Reverse removal procedure. Ensure that the
rubber seal is seated correctly.STOP, REVERSING, FOG GUARD BULBS
Service repair no - 86.40.74
Remove
1.Pull out side facing seat or pocket cover.
2.Unscrew fastener and remove access panel.
3.Turn bulb holder anti-clockwise to release.
4.Remove bulb.
NOTE: On vehicles fitted with rear air
conditioning remove access panel
housing rear loadspace light to gain
access.
Key
1. Access panel
2. Multiplug
3. Retaining nut
4. Bulb holder
5. Bulb
Refit
5.Reverse removal procedure.

86ELECTRICAL
18
REPAIR REAR LIGHTS, BUMPER MOUNTED
Service repair no - 86.41.42
Remove
1.From behind bumper disconnect light plugs.
2.Unscrew two retaining nuts and remove light unit
from bumper.
Refit
3.Reverse removal procedure.
NOTE: The black lead plug fits into the
direction indication light, the white lead
plugs into the tail light, the bulb holder
being colour coded red.DIRECTION INDICATOR, TAIL LIGHT BULBS
Service repair no - 86.41.43
Remove
1.Turn bulb holder anti-clockwise to release from
light unit.
2.Push and twist the bulb to remove.
Refit
3.Reverse removal procedure.

ELECTRICAL
19
REPAIR NUMBER PLATE LIGHTS
Service repair no - 86.40.86
Remove
1.Remove two screws and withdraw light unit.
2.Disconnect wiring leads and remove light unit.
3.Remove bulb.
Refit
4.Reverse removal procedure.DOOR EDGE LIGHT
Service repair no - 86.40.35
Remove
1.Pry lens from housing.
2.Disconnect wiring leads and remove light unit.
3.Remove bulb.
Refit
4.Reverse removal procedure.

86ELECTRICAL
20
REPAIR HIGH MOUNTED STOP LIGHT
Service repair no - 86.41.35
Remove
1.Remove two screws and lift off light reflector
body.
2.Unscrew retaining nut and remove lens unit from
rear door glass.
Refit
3.Reverse removal procedure.STOP LIGHT BULB
Service repair no - 86.40.87
Remove
1.Remove reflector body.
2.Turn bulb holder anti-clockwise to release from
light unit.
3.Push and twist the bulb to remove.
Refit
4.Reverse removal procedure.

ELECTRICAL
21
REPAIR INTERIOR LIGHT
Service repair no - 86.35.14
Remove
1.Pry out light unit from roof location.
2.Disconnect light switch plug.
Refit
3.Reverse removal procedure.
Bulb Removal.
1.Pry out interior light lens.
2.Remove bulb.
Refit
3.Reverse removal procedure.REAR LOADSPACE LIGHT
Service repair no - 86.41.40
Remove1.Pry light unit from trim panel.
2.Disconnect wiring leads.
3.Remove bulb.
Refit
4.Reverse removal procedure.

86ELECTRICAL
22
REPAIR SIDE REPEATER LIGHT
Service repair no - 86.50.59
Remove
1.Push the lens to the right and then pull outward
to detach lens and bulb holder from the panel.
2.Turn lens anti-clockwise and remove from bulb
holder.
3.Pull bulb from holder.
Refit
4.Reverse removal procedure.BUMPER MOUNTED SIDE LIGHT
Service repair no - 86.50.59
Remove
1.From behind bumper turn holder anti-clockwise
and release from light unit.
2.Pull bulb from holder.
Refit
3.Reverse removal procedure.