service LAND ROVER DISCOVERY 1995 Workshop Manual

SFI
13
REPAIR PLENUM CHAMBER
Service repair no - 19.22.46
Remove
1.Disconnect battery negative lead.
2.Slacken clip securing intake hose to plenum
chamber and release hose.
3.Remove split pin from throttle cable clevis pin.
4.Remove clevis pin.
5.Release and remove kick down cable clevis pin.
6.Disconnect vacuum hose from cruise actuator.
7.Release throttle cable from abutment bracket.
8.Remove front locknut from kick down cable.9.Release cable from bracket.
10.Disconnect breather hose from plenum.
11.Release clip and disconnect multiplug from
throttle position sensor (TP Sensor).
12.Disconnect multiplug from idle air control (IAC).
13.Remove 6 bolts securing plenum chamber.
14.Release plenum chamber from ram pipe
housing.
15.Fit approved hose clamp to water jacket coolant
hoses.
16.Tighten clamp.
17.Position cloth to absorb coolant spillage.
Do not carry out further dismantling if
component is removed for access only.
18.Slacken clips securing coolant hoses to plenum.

SFI
15
REPAIR REV: 09/95 Refit
25.Ensure all mating surfaces are clean.
26.Fit TP sensor. Ensure drive engages correctly
with throttle spindle.
27.Position clamp plate. Secure TP sensor with
bolts. Tighten to
2 Nm.
28.Using a new gasket, fit IAC. Secure with bolts.
Tighten to
2.3 Nm.
29.Ensure mating faces of water jacket and plenum
chamber are clean.
30.Using a new gasket, fit water jacket. Secure with
bolts. Tighten to
13 Nm.
31.Position throttle linkage bracket, fit and engage
return spring.
32.Secure linkage bracket to plenum chamber with
bolts. Tighten to
8 Nm.
33.Remove cloth from ram housing.
34.Ensure mating faces of plenum chamber and
ram pipe housing are clean.
35.Position plenum chamber. Connect coolant
hoses to water jacket. Secure with clips.
36.Remove clamp from coolant pipes. Remove
cloth.
37.Apply a thin, uniform coating of Loctite 577
sealant to sealing face of plenum chamber.
38.Fit plenum chamber.
39.Fit plenum chamber bolts. Tighten to
24 Nm.
40.Connect multiplugs to TP sensor and IAC.
41.Connect breather hose to plenum chamber.
42.Fit kick down cable to abutment bracket and fit
locknut.
43.Connect throttle cable to abutment bracket.
44.Connect vacuum hose to actuator.
45.Align throttle cable to lever. Fit clevis pin. Secure
clevis pin with split pin.
46.Align kick down cable to lever.
47.Fit clevis pin and secure clip.
48.Connect intake hose and secure with clip.
49.Reconnect battery negative lead.
50.Top up cooling system.RELAY MODULE - PRE ADVANCED EVAPS
Service repair no - 18.30.71
Remove
1.Release module from bracket.
2.Disconnect 2 multiplugs.
3.Remove module.
Refit
4.Reverse removal procedure.

19FUEL SYSTEM
16
REPAIRADD: 09/95 RELAY MODULE - ADVANCED EVAPS
Service repair no - 18.30.71
Remove
1.Release module from bracket.
2.Disconnect 2 multiplugs from module.
3.Remove module.
Refit
4.Position module, connect multiplugs and secure
to bracket.FUEL FILTER - ADVANCED EVAPS
Service repair no - 19.25.02
Remove
WARNING: Spilling of fuel is unavoidable
during this operation. Ensure all
necessary precautions are taken to
prevent fire and explosion.
WARNING: Ensure fuel handling
precautions given in section 1 -
Introduction are strictly adhered to when
carrying out following instructions.
1.Depressurise fuel system.
See fuel system -
depressurise - advanced evaps
2.Raise rear of vehicle.
WARNING: Support on safety stands.
3.Clean area around hose connections to prevent
ingress of foreign matter into fuel system. Clamp
inlet and outlet hoses to prevent fuel spillage
when disconnecting hoses.
4.Loosen 2 fuel line unions and disconnect hoses.
Remove and discard 'O' rings. Plug ends of
hoses to prevent ingress of dirt.
CAUTION: Use two spanners when
loosening or tightening unions.
5.Remove nut and bolt securing fuel filter bracket
to chassis and remove filter from bracket.

SFI
17
REPAIR ADD: 09/95 Refit
6.Fit a NEW filter to bracket.
NOTE: Ensure direction of flow arrow
stamped on canister is correct.
7.Position filter mounting bracket to chassis and
secure with nut and bolt.
8.Remove plugs from fuel hose ends.
9.Lubricate NEW 'O' rings with clean fuel and fit to
fuel hoses.
10.Connect fuel hoses to filter and tighten unions to
18 Nm.
CAUTION: Use two spanners when
loosening or tightening unions.
11.Remove stand(s) and lower vehicle.
12.Run the engine to check for any fuel leaks.FUEL PUMP AND GAUGE SENDER UNIT -
ADVANCED EVAPS
Service repair no - 19.45.03
A plastic fuel tank with a combined fuel pump and
gauge sender unit is fitted. The top flange of the pump
also houses a pressure sensor which is not removable
from the pump. The fuel pump is accessed through a
panel in the load space floor.
WARNING: Ensure that fuel handling
precautions given in 01 - Introduction are
strictly adhered to when carrying out
following instructions.
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Remove
1.Depressurise fuel system.
See fuel system -
depressurise - advanced evaps
2.Disconnect battery negative lead.
3.Check the amount of fuel in the tank. If the tank
is full, drain 2.4 US gallons (9 litres) minimum.
See fuel tank - draining - advanced evaps
4.Remove 6 screws securing tail door tread strip
and remove tread strip.
5.Remove RH luggage compartment side panel.
See CHASSIS AND BODY, Repair, rear
compartment lower trim panels

SFI
19
REPAIR ADD: 09/95
12.Using service tool LRT-19-009 loosen and
remove the metal locking ring.
13.Prise the pump from the tank opening using a
blunt instrument under the edge of the pump
flange. Once clear of the seal, tip the pump to
the right to allow fuel contained in the body of
the pump to drain into the tank.
CAUTION: Do not lift the pump from the
tank using the feed and return stubs.
14.Remove and discard seal.Refit
15.Fit NEW pump seal to tank opening.
16.Carefully lower pump into tank opening, pressing
firmly on the pump top flange to allow correct
positioning.
NOTE: Ensure location tag on pump top
flange is engaged correctly to tank
opening lip.
17.Fit locking ring and tighten to
35 Nmusing
service tool LRT-19-009.
18.Connect both fuel lines to the pump by pushing
the connectors down each line square to the
pump connection until the connectors positively
latch.
19.Connect vent hose to pressure sensor body.
20.Connect multiplugs to fuel pump and pressure
sensor.
21.Reconnect battery negative lead.
22.Refill tank with drained fuel.
23.Run the engine to check for any fuel leaks.
24.Fit access panel and secure with screws.
25.Reposition loadspace sound insulation and
carpet.
26.Fit RH luggage compartment side panel.
See
CHASSIS AND BODY, Repair, rear
compartment lower trim panels
27.Fit tail door tread strip and secure with screws.

19FUEL SYSTEM
20
REPAIRADD: 09/95 FUEL SYSTEM - DEPRESSURISE - ADVANCED
EVAPS
Service repair no - 19.50.02
WARNING: Fuel pressure of up to 2.5 bar
will be present in the system, even if the
engine has not been run for some time.
Always depressurise the system before
disconnecting any components in the fuel feed
line (between fuel pump and pressure regulator).
The spilling of fuel is unavoidable during this
operation. Ensure that all necessary precautions
are taken to prevent fire and explosion.
NOTE: Fuel pressure can be relieved at
fuel filter unions.
1.Position cloth around relevant union to protect
against fuel spray.
2.Carefully loosen union.
CAUTION: Use two spanners when
loosening or tightening unions.
3.Tighten union once fuel pressure is relieved.
4.Remove cloth.FUEL TANK - ADVANCED EVAPS
Service repair no - 19.55.01
WARNING: Ensure fuel handling
precautions given in section 01
Introduction are strictly adhered to when
carrying out following instructions.
CAUTION: Before disconnecting any part
of fuel system, it imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Remove
1.Disconnect battery negative lead.
2.Drain fuel tank completely.
See fuel tank -
draining - advanced evaps
3.Remove 6 screws securing tail door tread strip
and remove tread strip.
4.Remove RH luggage compartment side panel.
See CHASSIS AND BODY, Repair, rear
compartment lower trim panels

SFI
23
REPAIR ADD: 09/95
20.Remove nut and bolt securing RH side of upper
fuel tank strap to chassis.
21.Remove 4 nuts and bolts securing fuel tank
cradle.
22.Remove fuel tank cradle.
23.With assistance, tilt right hand side of tank
upwards and manoeuvre through chassis to
remove.
Do not carry out further dismantling if
component is removed for access only.
24.Release vent hose from tank pressure sensor.
25.Remove vent hose from 3 fuel tank clips.
26.Using service tool LRT-19-009 loosen and
remove the metal locking ring.
27.Prise the pump from the tank opening using a
blunt instrument under the edge of the lip of the
pump flange.
CAUTION: Do not lift the pump from the
tank using the feed and return stubs.
28.Remove and discard seal.

19FUEL SYSTEM
24
REPAIRADD: 09/95 Refit
29.Fit NEW pump seal to tank opening.
30.Carefully lower pump into tank opening, pressing
firmly on the pump top flange to allow correct
positioning.
NOTE: Ensure location tag on pump top
flange is engaged correctly to tank
opening lip.
31.Fit locking ring and tighten to
35 Nmusing
service tool LRT-19-009.
32.Fit vent hose to fuel tank clips and connect to
pressure sensor.
33.With assistance, fit fuel tank into position.
34.Fit fuel tank cradle and secure with nuts and
bolts.
35.Align upper fuel tank strap and secure with nut
and bolt.
36.Fit NEW clip to fuel filler neck hose.
37.Connect fuel filler neck internal breather to tank.
38.Connect fuel filler neck hose to tank.
39.Position fuel filler neck hose clip and tighten until
head shears.
40.Connect vent line quickfit connector to
liquid/vapour separator.
41.Connect vent line hose connection.
42.Position anti-roll [sway] bar straps and secure
with nuts and bolts.
43.Remove stand(s) and lower vehicle.
44.Connect both fuel lines to the pump by pushing
the connectors down each line square to the
pump connection until the connectors positively
latches.
45.Connect multiplugs to fuel pump and pressure
sensor.
46.Reconnect battery negative lead.
47.Refill tank with drained fuel.
48.Run the engine to check for any fuel leaks.
49.Fit access panel and secure with screws.
50.Reposition loadspace sound insulation and
carpet.
51.Fit RH luggage compartment side panel.
See
CHASSIS AND BODY, Repair, rear
compartment trim panels
52.Fit tail door tread strip and secure with screws.FUEL TANK - DRAINING - ADVANCED EVAPS
Service repair no - 19.55.02
WARNING: Before removing the fuel tank
it must be drained.
WARNING: Petrol/gasoline vapour is
highly flammable and in confined spaces
is also explosive and toxic. Always have a
fire extinguisher containing FOAM, CO2, GAS or
POWDER close at hand when handling or draining
fuel. See Introduction
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
NOTE: Assuming the fuel tank is FULL
drain the following quantities:
Renew Fuel pump = 9 Litres (2.4 US Gallons)
Renew Fuel filler neck = 22 Litres (6 US Gallons)
Renew Fuel tank = COMPLETE DRAIN
1.Depressurise fuel system.
See fuel system -
depressurise - advanced evaps
2.Disconnect battery negative lead.
3.Remove 6 screws securing tail door tread strip
and remove tread strip.
4.Remove RH luggage compartment side panel.
See CHASSIS AND BODY, Repair,

19FUEL SYSTEM
26
REPAIRADD: 09/95 FUEL FILLER NECK - ADVANCED EVAPS
Service repair no - 19.55.07
WARNING: Ensure that fuel handling
precautions given in 1 - Introduction are
strictly adhered to when carrying out
following instructions.
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Remove
1.Depressurise fuel system.
See fuel system -
depressurise - advanced evaps
2.Disconnect battery negative lead.
3.Check the amount of fuel in the tank. If the tank
is full drain 6 US gallons (22 litres) minimum.
See fuel tank - draining.
4.Remove 6 screws securing tail door tread strip
and remove tread strip.
5.Remove RH luggage compartment side panel.
See CHASSIS AND BODY, Repair, rear
compartment trim panels
6.Fold back loadspace carpet and sound
insulation to gain access to RH mudflap fixing.
7.Raise rear of vehicle.
WARNING: Support on safety stands.
8.Remove nut and bolt securing filler neck support
bracket to mud flap bracket.
NOTE: This fixing also retains the filler
neck earth strap.
9.Remove 5 nuts and bolts securing mud flap to
body.
10.Remove mud flap.

19FUEL SYSTEM
28
REPAIRADD: 09/95 Refit
26.Fit vent line to filler neck.
27.Fit NEW clip to filler neck hose.
28.Fit hose to filler neck.
29.Position filler neck hose clip and tighten until
head shears.
30.Fit filler neck assembly to vehicle.
NOTE: To aid fitment of filler neck through
body grommet apply a soap solution to lip
of grommet.
31.Fit NEW clip to fuel filler neck hose.
32.Connect fuel filler neck internal breather to tank.
33.Connect fuel filler neck hose to tank.
34.Position fuel filler neck hose clip and tighten until
head shears.
35.Connect vent line quickfit connector to
liquid/vapour separator.
36.Connect the pressure sensor breather pipe
connection.
37.Connect the vent line hose connection.
38.Fit mud flap and secure with nuts and bolts.
39.Position filler neck support bracket and earth
strap to mud flap bracket and secure with nut
and bolt.
40.Remove stand(s) and lower vehicle.
41.Reposition loadspace sound insulation and
carpet.
42.Fit RH luggage compartment side panel.
See
CHASSIS AND BODY, Repair,
43.Fit tail door tread strip and secure with screws.
44.Refill tank with drained fuel.
45.Fit fuel filler cap to filler neck.
46.Close filler flap, lock with ignition key and
remove key.
47.Reconnect battery negative lead.FUEL TANK FILLER CAP - ADVANCED EVAPS
Service repair no - 19.55.08
Remove
1.Fit ignition key to fuel filler flap lock and open
flap.
2.Remove screw securing cap retaining strap to
body.
3.Remove fuel filler cap.
Refit
4.Fit fuel filler cap.
5.Position cap retaining strap to body and secure
with screw.
6.Close filler flap, lock with ignition key and
remove key.