oil LAND ROVER DISCOVERY 1995 Workshop Manual

57STEERING
4
REPAIR
Refit
15.Position steering box to chassis side member,
ensuring locating peg is engaged. Tighten bolts
to
81 Nm.
16.Fit pinch bolt and nut securing universal joint to
power steering box. Tighten to
25 Nm.
17.Position tie bar, tighten bolts and nut to81 Nm,
starting with tie bar to mounting nut, then
loosen nut and bolts by one complete turn.
18.Check steering box, adjust if necessary.See
Adjustment, Power Steering Box
19.Refit drag link to drop arm tighten nut to40 Nm.
20.Fit undertray.
21.Lower vehicle to ground.
22.Remove plugs and refit pipes to steering box.
Tighten 16mm thread to
20 Nm.
14mm thread to15 Nm.
23.Remove filler cap. Fill reservoir to oil level mark
on dipstick. Use recommended fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids
and bleed power steering system.See
Power Steering System - Bleed
24.Recheck fluid level and replace cap.
25.With engine running, test steering system for
leaks by holding steering in both full lock
directions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute, to avoid oil overheating and
possible seal damage.
26.Test drive vehicle: using both full lock directions,
to settle steering components. If possible, drive
vehicle over speed bumps and include harsh
braking.
WARNING: Do not test drive vehicle on
public highway.
27.Drive vehicle in a straight line on level ground
and stop.
28.Tighten tie bar to mounting nut to
110 Nm.
29.Tighten bolts securing tie bar to81 Nm.
30.Ensure steering wheel is correctly aligned when
wheels are positioned straight ahead.
31.If necessary reposition steering wheel.
See
Steering Wheel
32.Road test vehicle.

STEERING
1
OVERHAUL POWER STEERING BOX
Service repair no - 57.10.07
Overhaul
NOTE: Overhaul of steering box should
not be carried out during the warranty
period.
WARNING: Wear safety glasses while
removing and refitting circlips and
retaining ring.
CAUTION: Absolute cleanliness is
essential when overhauling power steering
box.
1.Remove steering box from vehicle.See Repair,
Power Steering Box
Remove drop arm using extractor LRT-57-012.
Loosen drop arm securing nut, but do not
remove before using extractor. Remove dirt
excluder from output shaft.
2.Drain oil, remove blanking plugs and bleed
screw. Hold steering box over suitable container,
turn input shaft from lock to lock, until oil is
drained. Refit bleed screw.
3.Rotate retainer ring until one end is 12 mm from
extractor hole. Using a drift through hole in
cylinder, lift retaining ring from groove in cylinder
bore.
4.Remove retainer ring, using a screwdriver.
5.Turn input shaft (left lock on left hand drive, right
lock on right hand drive) until piston pushes out
cover. Turn input shaft fully in opposite direction,
applying pressure to piston.
6.Remove set screw retaining rack pad adjuster.
7.Remove rack adjuster and pad.
8.Remove sector shaft adjuster locknut.
9.Remove four bolts from sector shaft cover.
10.Screw in sector shaft adjuster until cover is
removed.
NOTE: Sealant is applied to hexagon
socket to 'tamperproof' sector shaft
adjuster
11.Slide out sector shaft.

STEERING
3
OVERHAUL
CAUTION: Do not remove sector shaft
bearings from casing. Replacement parts
are not available. If sector shaft bearings
are worn fit a new steering box.
21.Remove dirt excluder, circlip and seal from input
shaft housing bore.
CAUTION: The use of a seal puller is
recommended to prevent damage to
casing, and possible oil leaks.
INSPECTING
Piston
22.Discard all rubber seals and provide
replacements.
NOTE: A rubber seal is fitted behind
plastic ring on rack piston. Discard seal
and plastic ring.
Steering box casing
23.Examine piston bore for scoring and wear.
24.Examine feed tube.
25.Fit a new feed tube if damaged. Tighten to
22
Nm.
Sector shaft assembly
26.Check there is no side play on roller.
27.If side play on roller exists fit a new sector shaft.
28.Check condition of adjuster screw threads.
Check adjuster end float. Fit new adjuster if end
float exceeds 0.15 mm.
29.Examine bearing areas on shaft for excessive
wear.
30.Examine gear teeth for uneven or excessive
wear.

STEERING
5
OVERHAUL Rack thrust pad and adjuster
43.Examine thrust pad for scores.
44.Examine adjuster for wear in pad seat.
45.Fit new sealing ring to rack adjuster.
Rack and piston
46.Examine for excessive wear on rack teeth.
47.Ensure thrust pad bearing surface is free from
scores and wear.
48.Ensure piston outer diameters are free from
burrs and damage.
49.Examine seal and ring groove for scores and
damage.
50.Fit new ring to piston. Warm nylon seal and fit to
piston.
51.Slide piston assembly into cylinder with rack
tube outwards.Reassemble
NOTE: When fitting replacement oil seals
lubricate with recommended fluid and
ensure absolute cleanliness.
Sector shaft oil seal
52.Fit oil seal, lip side first.
53.Fit extrusion washer.
54.Fit dust seal, lipped side last.
55.Fit circlip.
Fitting valve and worm assembly
56.Refit original shims and inner bearing cup. Use
Petroleum Jelly to aid assembly.
NOTE: If original shims are not used, fit
shims of 0.76 mm thickness.
57.Fit inner cage and bearings assembly.
58.Fit valve and worm assembly.
59.Fit outer cage and bearings assembly.
60.Fit outer bearing cup.

STEERING
9
OVERHAUL Input shaft oil seal
92.Fit seal, lip side first, into housing. Use seal
saver LRT-57-016 and seal installer
LRT-57-026. Note that seal is fitted to a depth of
4.75 - 5.00 mm from face of box.
93.Secure seal with circlip.
94.Smear inner lip of dirt excluder with PTFE
grease. Fit dirt excluder using LRT-57-027.
When fitted correctly outer shoulder of excluder
is 4.00 - 4.50 mm from face of box, dimension X
in RR3941M.
95.Remove drop arm. Smear inner lip of dirt
excluder with PTFE grease and refit, ensuring
outer lip is flush with casing.
96.With input shaft on centre, line up centralising
holes in drop arm and steering box see inset in
RR3940M. Fit drop arm to steering box using a
new tab washer. Tighten to
176 Nm,bend over
tab.
97.Fit steering box.See Repair, Power Steering
Box

60FRONT SUSPENSION
2
DESCRIPTION AND OPERATION AXLE LOCATION
The front axle is controlled longitudinally, by two forged steel radius arms and transversely by a panhard rod.
Front axle suspension
1. Panhard rod - transverse location
2. Radius arms - longitudinal location
3. Coil springs
4. Shock absorber
Long travel coil springs and hydraulic shock absorbers, provide the springing for each wheel.

REAR SUSPENSION
1
DESCRIPTION AND OPERATION AXLE LOCATION
Longitudinal location of the rear axle is by solid round section steel link arms and a forged "A" frame, upper link
assembly, which is secured to a chassis cross member and provides transverse control. Long travel coil springs
and hydraulic shock absorbers provide the springing for each wheel.
Rear axle suspension
1. "A" frame, upper link assembly - transverse location
2. Lower link assembly - longitudinal location
3. Coil springs
4. Shock absorber

REAR SUSPENSION
1
REPAIR REAR ROAD SPRING
Service repair no - 64.20.01
Remove
1.Loosen rear road wheel retaining nuts.
2.Support chassis on stands and remove wheels.
3.Support rear axle weight with jack.
4.Disconnect shock absorbers at one end.
5.Position coil spring compressor correctly on road
spring.
6.Compress spring evenly to facilitate removal.
7.Lower axle to free road spring from upper seat.
CAUTION: Avoid lowering axle further than
rear brake flexible hose will allow.
8.Remove spring retainer plate.
9.Withdraw road spring, and spring isolator.
10.Lift off spring seat.
Refit
11.Reverse removal procedure.REAR SHOCK ABSORBER
Service repair no - 64.30.02.
Remove
1.Loosen road wheel retaining nuts.
2.Support chassis on stands. Remove road wheel
and support rear axle weight with jack.
3.Remove fixings and withdraw shock absorber
from axle bracket.
4.Remove upper fixings.
5.Withdraw shock absorber.
6.If required remove mounting bracket
7.If required remove mounting rubbers.
Refit
8.Reverse removal procedure.

BRAKES
1
REPAIR GENERAL BRAKE SERVICE PRACTICE
Brake fluid precautions
WARNING: Do not allow brake fluid to
come into contact with eyes or skin.
CAUTION: Brake fluid can damage
paintwork, if spilled wash off immediately
with plenty of clean water.
CAUTION: Use only correct grade of brake
fluid. If an assembly fluid is required use
ONLY brake fluid. Do NOT use mineral oil,
i.e. engine oil etc.
CAUTION: Thoroughly clean all brake
calipers, pipes and fittings before
commencing work on any part of the brake
system. Failure to do so could cause foreign
matter to enter the system and cause damage to
seals and pistons which will seriously impair the
efficiency of the brake system.
·To ensure the brake system efficiency is not
impaired the following warnings must be
adhered to :-
·DO NOT use any petroleum based cleaning
fluids or any proprietary fluids containing
petrol.
·DO NOT use brake fluid previously bled from
the system.
·DO NOT flush the brake system with any fluid
other than the recommended brake fluid.
The brake system should be drained and flushed
at the recommended service intervals.
Cover all electrical terminals carefully to make
absolutely certain that no fluid enters the
terminals and plugs.FLUID LEVEL CHECK / TOP UP
WARNING: Clean reservoir body and filler
cap before removing cap. Use only fluid
from a sealed container.
1.Park vehicle on level ground.
2.Check level is between 'MIN' and 'MAX' marks.
3.If level is below 'MIN' mark top up fluid level to
'MAX' mark on reservoir, using correct fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids
Do not fill reservoir above maximum line

BRAKES
13
REPAIR FRONT BRAKE CALIPERS
Service repair no - 70.55.03
Service repair no - 70.55.16
Service tool:
LRT-70-500 - Piston clamp
Before starting repair refer to general brake service
practice.
See General Brake Service Practice
Remove caliper
1.Loosen front wheel retaining nuts, raise front of
vehicle, lower onto axle stands, remove wheels.
2.Expose flexible brake hose by moving coiled
protective covering.
3.Using a recognised hose clamp, clamp hose to
prevent loss of brake fluid.
4.Disconnect rigid brake pipe from flexible hose,
seal exposed ends to prevent ingress of dirt.
5.Remove split [cotter] pin, retaining pins and
springs, withdraw pads. If refitting pads, identify
them for assembly to original locations.
6.Loosen bolts and remove caliper.
Repair
Do not separate caliper halves
7.Clean outer surfaces of caliper using aerosol
brake cleaner.
8.Using special tool LRT-70-500, clamp pistons in
inboard half of caliper. Gently, keeping fingers
clear, and withCAUTION,apply air pressure to
fluid inlet port to expel pistons. It is unlikely that
pistons will expel at same time, regulate rate
with a suitable piece of wood between
appropriate piston and caliper.
9.Finally remove pistons, identifying them with
their respective bores.
10.Remove wiper seal retainer by inserting a blunt
screwdriver between retainer and seal. Pry
retainer carefully from mouth of bore.
11.Taking care not to damage seal grooves, extract
wiper seal and fluid seal.
12.Clean bores, pistons and seal grooves using
clean brake fluid only. If caliper or pistons are
corroded, or their condition is not perfect, new
parts must be fitted.