ECU LAND ROVER DISCOVERY 1995 Workshop Manual

51REAR AXLE AND FINAL DRIVE
4
REPAIR Refit
10.Clean stub axle. Retract ABS sensor slightly
from sensor sleeve, if applicable
11.Fit hub assembly to stub axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
61 Nm.
Back off adjusting nut 90°. Tighten to4 Nm.
This will give the required hub end float of
0,010mm
14.Fit a new lock washer.
15.Fit locknut. Tighten to61 Nm.
16.Tab over lock washer to secure adjusting nut
and locknut.
17.Using a new joint washer fit axle shaft to hub,
secure with five bolts. Tighten to
65 Nm.
18.Fit brake caliper. Tighten to82 Nm.
Secure brake pipes to axle casing.
19.If applicable, set ABS brakes sensor.
Push sensor in until it touches sensor ring then
rotate hub to set sensor.
20.Fit road wheel, remove axle stands and final
tighten road wheel nuts to
126 Nm.
21.Operate footbrake to locate brake pads before
driving vehicle.

REAR AXLE AND FINAL DRIVE
1
OVERHAUL AXLE DIFFERENTIAL ASSEMBLY
Service repair no - 51.15.07.
DISMANTLE
NOTE: Mark differential components so
their original positions relative to other
components is maintained. Bearing caps
must not be interchanged.
1.Remove axle shafts then differential assembly
fom axle.
2.Remove roll pin securing bearing nut locking
fingers to bearing caps. Remove locking fingers.
3.Loosen bearing cap bolts and mark caps for
assembly.
4.Using service tool LRT-54-508, remove bearing
adjusting nuts.
5.Remove bearing cap bolts and bearing caps.
6.Remove crown wheel differential unit and
bearings.
Remove pinion FRONT AXLE DIFFERENTIAL
ONLY
7.Remove pinion flange nut using service tool
LRT-51-003 to restrain flange.
8.Remove washer and pinion drive flange.
9.Remove pinion complete with bearing and outer
bearing shims.
10.Remove pinion flange oil seal, spacer and
bearing.
Remove pinion REAR AXLE DIFFERENTIAL ONLY
7.Remove pinion flange centralizing peg using
service tool LRT-51-008.
8.Remove pinion flange nut using service tool
LRT-51-003 to restrain flange.
9.Remove pinion complete with bearing and outer
bearing shims.
10.Remove pinion flange oil seal and bearing.
11.Using service tool LRT-54-505, remove pinion
head bearing track and shim and drive out outer
bearing of differential housing.

51REAR AXLE AND FINAL DRIVE
2
OVERHAUL
12.Remove pinion head bearing with service tool
LRT-99-002.
13.Remove bolts and washers securing crown
wheel to differential flange. Remove crown
wheel.
14.Remove differential carrier bearings.
15.Remove circlips and extract differential cross
shaft.
16.Withdraw differential gears and pinions.
17.Clean all components.
INSPECTION
18.Check all bearings for wear and pitting.
19.Check all gears for wear, scuffing, pitting and
damaged teeth.
20.Supplied as matched sets are: crown wheel and
pinion, pinion housing and bearing caps.
ASSEMBLE
Differential gears
21.Fit differential gears to differential housing.
22.Fit differential cross shaft and circlips.

REAR AXLE AND FINAL DRIVE
7
OVERHAUL PINION PRELOAD SHIMS
PART No. INCH MM
FTC3869 .085 2.155
FTC3870 .084 2.130
FTC3871 .083 2.105
FTC3872 .082 2.080
FTC3873 .081 2.055
FTC3874 .080 2.030
FTC3875 .079 2.005
FTC3876 .078 1.980
FTC3877 .077 1.955
FTC3878 .076 1.930
FTC3879 .075 1.905
FTC3880 .074 1.880
FTC3881 .073 1.855
FTC3882 .072 1.830
FTC3883 .071 1.805
FTC3884 .070 1.780
FTC3885 .069 1.755
FTC3886 .068 1.730
FTC3887 .067 1.705
FTC3888 .066 1.680
FTC3889 .065 1.655
FTC3890 .064 1.630
FTC3891 .063 1.605
FTC3892 .062 1.580
FTC3893 .061 1.555
FTC3894 .060 1.530
FTC3895 .059 1.505
FTC3896 .058 1.480
Fitting Pinion Oil Seal
59.Coat outer diameter of seal with grease. Fit seal
lip side leading flush with end face of housing
using tool LRT-51-001.
Fit pinion drive flange - front axle differential
60.Lubricate seal lips with axle oil.
61.Fit spacer and pinion drive flange to differential.
62.Secure flange with washer and nylon nut.
Tighten to
130 Nm.
Fit pinion drive flange - rear axle differential
60.Lubricate seal lips with axle oil.
61.Fit pinion drive flange to differential and secure
with washer and nylon nut. Tighten to
130 Nm.
62.Coat centralizing peg with Loctite 601 or 638 and
fit over pinion retaining nut in drive flange.

FRONT AXLE AND FINAL DRIVE
1
REPAIR FRONT AXLE ASSEMBLY
Service repair no - 54.15.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
axle when lowering or repositioning axle.
1.Support chassis front.
2.Remove road wheels.
3.Support axle weight with hydraulic jack.
4.Remove radius arms to chassis frame nuts.
5.Disconnect steering damper from track rod.
Using a extractor remove track rod links from
swivel pin arms.
6.Remove four nuts and bolts securing radius
arms to axle bracket.
7.Remove radius arms.
8.Remove bolts securing brake hose brackets.
Refit bolts to prevent oil leakage.
9.Remove ABS sensor, if applicable.
10.Remove bolts from brake calipers and tie to one
side.
11.Remove nuts and washers securing shock
absorbers to axle.
12.Disconnect drag link from swivel pin housing
arm.
13.Remove two nuts and bolts securing panhard
rod to axle bracket. Lift rod clear of axle.
14.Mark for reassembly drive shaft flanges.
Remove four nuts and bolts, tie propeller shaft to
one side.
15.Lower axle assembly and remove road springs.
16.Disconnect anti-roll[sway] bar link.
See FRONT
SUSPENSION, Repair, Anti-Roll[Sway] Bar
Ball Joint Links
17.Remove axle assembly.
Refit
18.Position axle under vehicle, supporting left side
of axle.
19.Reverse removal procedure.
20.Tighten propeller shaft bolts to
47 Nm.
21.Tighten panhard rod to axle bracket to88 Nm.
22.Tighten drag link to hub arm to40 Nm.
23.Tighten upper swivel pin bolts.See
Specifications, torque, Torque Values
24.Tighten radius arms to axle bolts to197 Nm.
25.Tighten radius arms to chassis side member
nuts to
197 Nm.
26.Tighten track rod end to40 Nm.
Fit new split [cotter] pin.

FRONT AXLE AND FINAL DRIVE
3
REPAIR FRONT HUB ASSEMBLY
Service repair no - 60.25.01.
Remove
1.Loosen front wheel nuts, jack up vehicle and
lower onto axle stands and remove road wheel.
2.Release brake hose clips and remove brake
caliper. Secure to one side.
3.Lever off dust cap.
4.Remove circlip and drive shaft shim from
driveshaft.
5.Remove five bolts and withdraw driving member
and joint washer.
6.Bend back lock washer tabs.
7.Remove locknut and lock washer.
8.Remove hub adjusting nut.
9.Remove spacing washer.
10.Remove hub and brake disc assembly complete
with bearings.HUB COMPONENTS
1. Dust cap.
2. Drive shaft circlip.
3. Drive shaft shim.
4. Drive member.
5. Drive member joint washer.
6. Drive member retaining bolt.
7. Lock nut.
8. Lock washer.
9. Hub adjusting nut.
10. Spacing washer.
11. Outer bearing.
12. Hub.
13. Inner bearing.
14. Grease seal.
15. Brake disc
16. Disc retaining bolt.

54FRONT AXLE AND FINAL DRIVE
4
REPAIR Refit
11.Clean stub axle and drive shaft and fit hub
assembly to axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
61 Nm.
14.Back off adjusting nut 90°. Tighten to4 Nm.
This will give the required hub end float of
0,010mm
15.Fit a new lock washer.
16.Fit locknut. Tighten to61 Nm.
17.Tab over lock washer to secure adjusting nut
and locknut.
18.Fit a new joint washer to driving member and fit
member to hub and secure with five bolts.
Tighten to
65 Nm.
19.Fit original drive shaft shim and secure with a
circlip.
20.To check drive shaft end play mount a dial
gauge using bracket LRT-99-503 and rest pin in
a loaded condition on end of drive shaft.
21.Fit a suitable bolt to threaded end of drive shaft.
Move drive shaft in and out noting dial gauge
reading. End play should be between0,08 to
0,25 mm.
22.If end play requires adjustment, remove circlip,
measure shim thickness and fit an appropriate
shim to give required end-play.
23.Remove bolt from drive shaft, fit circlip and dust
cap.
24.Fit brake caliper. Tighten to
82 Nm.
25.Bleed brake system.See BRAKES, Repair,
Brake System Bleed
26.Fit road wheel, remove axle stands and tighten
road wheel nuts to
126 Nm.
27.Operate footbrake to locate brake pads before
taking vehicle on road.

FRONT AXLE AND FINAL DRIVE
5
OVERHAUL Swivel pin housing
22.Remove bolts securing oil seal retaining plate
and joint washer. Release assembly from swivel
pin housing.
NOTE: Removal of oil seal and retaining
plate is achieved when swivel bearing
housing is removed.
23.Remove two bolts, retaining lower swivel pin to
housing.
24.Remove brake disc shield bracket.
25.tap lug to remove lower swivel pin and joint
washer.
26.Remove two bolts retainin brake hose bracket
and top swivel pin.
27.Remove bracket, top swivel pin and shims.
28.Remove swivel pin housing while retrieving
lower and upper bearings.
Swivel bearing housing
29.Remove lower bearing track from swivel bearing
housing.
NOTE: Use upper bearing opening to gain
access to lower bearing track.
30.Remove seven bolts retaining swivel bearing
housing to axle case.
31.Remove inner oil seal from back of housing.
32.Remove top bearing track from swivel bearing
housing.
NOTE: Use lower bearing opening to gain
access to upper bearing track.
33.If worn, pitted or damaged, renew housing.
34.Fit upper and lower bearing tracks into swivel
bearing housing.
CAUTION: Ensure bearing tracks are fitted
square or damage could occur.
35.With seal lips trailing, fit swivel housing inner oil
seal into rear of housing. Grease seal lips.Fit swivel pin housing
36.Coat swivel bearing housing to axle casing bolts
with Loctite 270 or equivalent.
37.Coat both sides of joint washer with a sealing
compound. Position swivel bearing housing to
axle mating face.
38.Place retaining plate, joint washer and oil seal
over axle flange ready for assembly.
39.Fit swivel bearing housing to axle flange with
seven bolts. Tighten to
73 Nm.
40.Grease and fit upper and lower swivel pin taper
roller bearings.
41.Position swivel pin housing over swivel bearing
housing.
42.Coat joint washer both sides with sealing
compound and position on lower swivel pin.
43.Loosely fit brake shield bracket plus lower swivel
pin with lug outboard to swivel pin housing.
44.Loosely fit top swivel pin plus existing shims and
brake hose bracket to swivel pin housing.
45.Apply Loctite 270 or equivalent to lower swivel
pin bolts. Tighten to
78 Nmbend over lock
tabs.
46.Tighten top swivel pin bolts to
78 Nm.

54FRONT AXLE AND FINAL DRIVE
6
OVERHAUL Swivel assembly components
1. Swivel pin housing
2. Top swivel pin and brake hose bracket
3. Upper and lower swivel pin bearings
4. Shim
5. Retaining plate and washer
6. Oil seal
7. Joint washer
8. Swivel bearing housing
9. Joint washer
10. Lower swivel pin
11. Mudshield bracket
12. Swivel housing inner oil sealCheck and adjust preload on bearings
NOTE: Swivel housing oil seal and axle
should not be fitted.
47.Attach a spring balance to ball joint bore and pull
balance to determine effort required to turn
swivel pin housing.
Resistance, once initial inertia has been
overcome, should be1.16 to 1.46 kg.Adjust by
removing or adding shims to top swivel pin.
48.When setting is correct remove top swivel bolts,
apply Loctite 270 or equivalent. Refit to
78 Nm,
and bend over lock tabs.
49.Apply recommended grease between lips of
swivel oil seal.
50.Fit oil seal, joint washer and retaining plate with
seven bolts and spring washers to
11 Nm.
51.Fit tie rod and drag link and secure with new
cotter pins. Tighten to
40 Nm.
52.Fit brake disc shield.
53.Loosely fit lock stop bolt and nut.
54.Apply a recommended grease between lips of
swivel housing oil seal.
55.Secure oil seal with retaining plate and securing
bolts. Tighten to
11 Nm.
56.Fit track-rod and drag link and secure with new
cotter pins.
57.Loosely fit lock stop bolt for later adjustment.
58.Fit brake disc shield.

FRONT AXLE AND FINAL DRIVE
7
OVERHAUL Fit driveshaft and stub axle
59.Insert axle shaft, and when differential splines
are engaged, push assembly in fully.
CAUTION: Take care not to damage axle
shaft oil seals.
60.Place a new joint washer in position on swivelpin
housing to stub axle mating face. Coat threads
of stub axle bolts with Loctite 270.
61.Fit stub axle with flat at 12 o'clock position.
CAUTION: Ensure that constant velocity
joint bearing journal is butted against
thrust ring on stub axle. Before stub axle
is secured.
62.Place mud shield in position and secure stub
axle to swivel pin housing with six bolts and
tighten evenly to
65 Nm.
63.Fit brake jump hoses to brake jump hose
bracket.
64.Fit front hub complete assembly.
See Repair,
Front Hub Assembly
65.Check swivel pin housing oil drain plug is fitted.
66.Fill swivel assembly to correct level, with new oil.
See SECTION 10, Maintenance, Under
Vehicle Maintenance
67.Set steering lock stop bolts to provide a
clearance of 20mm.
See STEERING,
Adjustment, Steering Lock Stops
FRONT STUB AXLE, CONSTANT VELOCITY JOINT
AND SWIVEL PIN HOUSING ABS
Service repair no - 60.15.43.
Remove stub axle, axle shaft and constant
velocity joint.
1.Remove front hub assembly.
See Repair,
Front Hub Assembly
2.Drain swivel pin housing and refit plug.
3.Remove six bolts retaining stub axle to swivel
housing.
4.Remove mud shield.
5.Remove stub axle and joint washer.
6.Pull out axle shaft and constant velocity joint
from axle casing.