ECU LAND ROVER DISCOVERY 1995 Workshop Manual

ELECTRICAL
49
REPAIR Refit
8.Fit bulb to lens.
9.Secure bulb retaining clip.
10.Connect 2 Lucars to bulb.
11.Position lamp lens to shroud.
12.Position lamp to bracket and secure fog lamp
adjustment ball joint to bracket.
13.Position spacers, align lamp to bracket and
secure with Torx screws.
14.Fit front fog lamp.
See fog lamp - front; Refit
CLOCK
Service repair no - 88.15.07
Remove
1.Remove drinks tray.
See CHASSIS AND
BODY, Repair, drinks tray
2.Release 4 clock panel securing tags.
3.Release clock panel from louvre panel.
4.Disconnect 2 multiplugs from clock.
5.Remove clock.
Refit
6.Position clock.
7.Connect multiplugs to clock and secure clock to
louvre panel.
8.Fit drinks tray.
See CHASSIS AND BODY,
Repair, drinks tray; Refit
REAR SPEAKER
Service repair no - 88.15.12
Remove
1.Remove 4 screws securing speaker.
2.Release speaker and disconnect 2 Lucars.
3.Remove speaker.
Refit
4.Position speaker, connect Lucars and secure
with screws.

86ELECTRICAL
50
REPAIR DIGITAL DIESEL SHUT-OFF VALVE (DDS) - 97 MY
Service repair no - 86.77.00
Remove
1.Remove fuel injection pump.
See FUEL
SYSTEM, Repair, fuel injection pump and
timing
2.Drill into 2 break-off screws to a depth of
approximately 5 mm using a 3.2 mm drill.
CAUTION: Use a drill bushing to guide the
drill during the above.
3.Using an 'Easy-out' remove 2 valve retaining
screws and discard.
4.Release DDS valve from fuel shut-off solenoid.
5.Remove protective cap from fuel shut-off
solenoid electrical connection.
6.Remove fuel shut-off solenoid terminal nut and
remove DDS valve.
Refit
7.Position DDS terminal lead to fuel shut-off
solenoid and secure with nut tightened to
2Nm.
8.Position DDS valve to fuel shut-off solenoid .
9.Position clamping plate to DDS valve and tighten
shear bolts simultaneously until heads shear.
10.Fit fuel injection pump.
See FUEL SYSTEM,
Repair, fuel injection pump and timing; Refit
ANTENNA AMPLIFIER - 97 MY
Service repair no - 86.50.29
Remove
1.Remove RH alpine light trim casing.
See
CHASSIS AND BODY, Repair, alpine light
trim casing
2.Release amplifier to sixth light connector and
seal finisher.
3.Remove screw securing amplifier to body and
release from location.
4.Disconnect co-axial cable from amplifier.
5.Disconnect Lucar from amplifier.
6.Remove amplifier.
Refit
7.Fit amplifier, connect co-axial cable and Lucar to
amplifier.
8.Position amplifier to location and secure with
screw.
9.Secure amplifier lead through seal finisher and
connect to sixth light.
10.Fit RH alpine light trim casing.
See CHASSIS
AND BODY, Repair, alpine light trim casing;
Refit

ELECTRICAL
1
OVERHAUL DISTRIBUTOR-LUCAS 35DLM8
Overhaul
DISTRIBUTOR CAP
Service repair no - 86.35.10
1.Unclip and remove cap
2.Fit a new cap if faulty.
3.Clean cap and HT brush with a lint free cloth.
ROTOR ARM
Service repair no - 86.35.16
1.Pull rotor arm from shaft.
2.Fit a new rotor arm if faulty.
INSULATION COVER (FLASH SHIELD)
Service repair no - 86.35.40
1.Remove cover secured by three screws.
2.Fit a new cover if faulty.
VACUUM UNIT
Service repair no - 86.35.21
1.Remove two screws from vacuum unit securing
bracket. Disengage vacuum unit connecting rod
from pick-up base plate connecting peg.
Withdraw vacuum unit from distributor body.AMPLIFIER MODULE
Service repair no - 86.35.30
1.Remove two screws and withdraw module.
2.Remove gasket.
3.Remove two screws and cast heatsink.
WARNING: Amplifier module is a sealed
unit containing Beryllia. This substance is
extremely dangerous if handled. DO NOT
attempt to open or crush module.
PICK-UP AND BASE PLATE ASSEMBLY
Service repair no - 86.35.42
1.Use circlip pliers to remove circlip retaining
reluctor on rotor shaft.
2.Remove flat washer, and 'O' ring recessed in top
of reluctor.
3.Gently withdraw reluctor from shaft, taking care
not to damage teeth.
NOTE: Coupling ring fitted beneath
reluctor.
4.Remove three support pillars and cable
grommet. Lift out pick-up and base plate
assembly.
NOTE: Do not disturb two barrel nuts
securing pick-up module, otherwise air
gap will need re-adjustment.
5.Fit a new pick-up and base plate assembly if
module is known to be faulty, otherwise check
pick-up winding resistance (2k-5k ohm).
Reassemble
6.This is mainly a reversal of dismantling
procedure, noting following points: