service LAND ROVER DISCOVERY 1995 Workshop Manual

CHASSIS AND BODY
39
REPAIR SUNROOF ELECTRIC MOTORS
Service repair no - 76.82.84/85
FRONT MOTOR
Remove
1.Disconnect battery negative lead.
2.Ensure sunroof is in normally closed position
NOTE: If the electric motor has failed the
sunroof can be closed manually using an
allen key to turn motor spindle A.
3.Remove switch panel from stowage pocket
panel
4.Remove interior lamp from stowage pocket
panel
5.Remove alarm ultrasonic unit.
6.Unscrew ten fixings and remove stowage pocket
from headlining.
7.Disconnect motor wiring multiplug.
8.Remove three screws and motor.
Refit
9.Reverse removal procedure.
CAUTION: Ensure the motor is aligned
with fixing holes and the sunroof is in the
normally closed position. DO NOT rotate
the motor drive spindle in the rack - this may
result in incorrect operation of the sunroof.REAR MOTOR
Remove
1.Disconnect battery negative lead.
2.Ensure sunroof is in normally closed position
NOTE: If the electric motor has failed the
sunroof can be closed manually using an
allen key to turn motor spindle.
3.Remove headlining.
See headlining.
4.Disconnect motor wiring multiplug.
5.Remove three screws and motor.
Refit
6.Reverse removal procedure.
CAUTION: Ensure the motor is aligned
with fixing holes and the sunroof is in the
normally closed position. DO NOT rotate
the motor drive spindle in the rack - this may
result in incorrect operation of the sunroof.

76CHASSIS AND BODY
40
REPAIR SUNROOF ELECTRIC CONTROL UNIT
Service repair no - 76.82.73
The control unit serves both front and rear sunroofs
and is sited above the front switches behind
headlining.
Remove
1.Disconnect battery negative lead.
2.Ensure sunroof is in normally closed position.
NOTE: If the electric motor has failed the
sunroof can be closed manually using an
allen key to turn motor spindle.
3.Remove switch panel from stowage pocket
panel
4.Remove interior lamp from stowage pocket
panel
5.Remove alarm ultrasonic unit.
6.Unscrew ten fixings and remove stowage pocket
from headlining.
7.Disconnect electric plugs from control unit.
8.Remove two retaining screws and control unit.
Refit
9.Reverse removal procedure.

CHASSIS AND BODY
41
REPAIR SUNROOF ASSEMBLY - MANUAL, FRONT AND
REAR
Service repair no - 76.83.01
Remove
1.Close sunroof.
2.Remove headlining.
See headlining.
3.Remove screws and manual regulator from
clamping frame.
See sunroof regulator
manual.
4.Disconnect drain tubes from each side of
clamping frame.
5.Remove 13 screws and clamping frame from
upper frame.
6.Remove upper frame assembly from roof
aperture.Refit
7.Position upper frame assembly into roof
aperture.
8.Locate clamping frame and reconnect drain
tubes.
9.Loosely fit screws, centralise upper frame and
clamping frame assemblies and then tighten
screws.
10.Reverse removal procedure.
Sunroof components
1. Glass panel
2. Capnut and washer
3. Screw
4. Upper frame assembly5. Clamping frame assembly
6. Screw
7. Edging trim
8. Drain tube

76CHASSIS AND BODY
42
REPAIR SUNROOF REGULATOR MANUAL
Service repair no - 76.83.03/04
FRONT
Remove
1.Ensure sunroof is in normally closed position.
2.Remove retaining screw and regulator handle.
3.Remove switch panel from stowage pocket
panel
4.Remove interior lamp from stowage pocket
panel
5.Remove alarm ultra sonic unit.
6.Unscrew ten fixings and remove stowage pocket
from headlining.
7.Remove two retaining screws and regulator from
clamping frame.
Refit
8.Reverse removal procedure.
CAUTION: Ensure the regulator is aligned
with fixing holes and the sunroof is in the
normally closed position. DO NOT rotate
the regulator spindle in the rack - this may result
in incorrect operation of the sunroof.REAR
Remove
1.Ensure sunroof is in normally closed position.
2.Remove retaining screw and regulator handle.
3.Remove headlining.
See headlining.
4.Remove two retaining screws and regulator from
clamping frame.
Refit
5.Reverse removal procedure.
CAUTION: Ensure the regulator is aligned
with fixing holes and the sunroof is in the
normally closed position. DO NOT rotate
the regulator spindle in the rack - this may result
in incorrect operation of the sunroof.

CHASSIS AND BODY
43
REPAIR SUN BLIND ASSEMBLY
Service repair no - 76.82.78
Remove
1.Open sunroof to the tilt position.
2.Remove the trim finisher from the sunroof
surround.
3.Release the headlining locally to access under
clamping frame of the sunroof.
4.Lever forward and upward the rear leg of 3
retaining clips to release sun blind roll assembly.
Refit
5.Ensure front leg of retaining clips are located.
6.Push in rear leg of retaining clip.
7.Reverse removal procedure.CENTRE CONSOLE
Service repair no - 76.52.02
Remove
1.Disconnect battery earth lead.
2.Release tranfer gear lever gaiter from console.
3.Remove transfer gear lever gaiter and knob
assembly.
4.Release gear selector lever gaiter from centre
console.
5.Remove gear selector lever gaiter and knob
assembly.
6.Remove centre console rubber mat.

CHASSIS AND BODY
45
REPAIR Refit
20.Position centre console assembly, ensuring
harnesses and connectors are not trapped and
are routed to their correct locations.
21.Connect cigar lighter multiplug and illumination
bulb Lucar.
22.Align centre console to body fixings and fascia.
23.Fit and tighten screws securing centre console to
body.
24.Lubricate hand brake lever to cable clevis pin.
25.Align hand brake cable to lever, fit clevis pin and
secure with clip.
26.Secure hand brake lever gaiter to centre
console.
Models fitted with electric front seats
27.Position electric front seat switches,connect
multiplugs and secure to centre console.
All models
28.Position centre console switch pack and connect
multiplugs to switches.
29.Align switch pack to centre console and secure
with screws.
30.Fit centre console switch pack cover.
31.Fit centre console rubber mat.
32.Fit gear selector lever knob and secure gaiter.
33.Fit transfer gear lever knob and secure gaiter.
34.Reconnect battery earth lead.DRINKS TRAY
Service repair no - 76.46.41
Remove
1.Disconnect battery negative lead.
2.Remove ash tray.
See ash tray - dash panel
central louvre panel.
3.Remove switch pack.See switch pack - dash
panel central louvre panel.
4.Remove 6 screws securing drinks tray to dash
panel central louvre panel.
5.Remove drinks tray.
Refit
6.Position drinks tray to dash panel central louvre
panel and secure with screws.
7.Fit switch pack.
See switch pack - dash panel
central louvre panel.
8.Fit ash tray.See ash tray - dash panel central
louvre panel.
9.Connect battery negative lead.

76CHASSIS AND BODY
46
REPAIR DASH PANEL CENTRAL LOUVRE PANEL
Service repair no - 76.46.42
Remove
1.Disconnect battery negative lead.
2.Remove radio.
See ELECTRICAL, Repair,
radio.
3.Release tags securing radio cage to louvre
panel and remove cage.
4.Remove clock.
See ELECTRICAL, Repair,
clock.
5.Release 4 coin tray securing tags.
6.Remove coin tray.
7.Remove 3 heater control and blower switch
knob.
8.Remove 2 screws securing heater graphic
display panel and remove panel.
9.Remove 4 screws securing heater control unit to
panel.
10.Working through coin tray aperture, remove
screw securing panel.
11.Working through clock aperture, remove screw
securing panel.
12.Loosen 2 uppermost panel retaining screws.
NOTE: On some models the panel is fitted
with an LED. In this case, manoeuvre LED
from panel and disconnect.
13.Remove panel retaining screw cover.

CHASSIS AND BODY
47
REPAIR
14.Remove 2 screws securing louvre panel.
15.Remove louvre panel from dash panel.
Refit
16.Position louvre panel, feed harness connectors
through their correct apertures,and align to dash
panel.
CAUTION: When refitting avoid trapping of
electrical wiring.
17.Fit and tighten screws securing louvre panel.
18.Fit panel retaining screw cover.
19.Position heater control unit to panel and secure
with screws.
20.Fit heater graphic display panel and secure with
screws.
21.Fit heater control and blower switch knobs.
22.Fit clock.
See ELECTRICAL, Repair, clock.
23.Position coin tray and secure to tags.
24.Position radio cage, feed electrical connectors
and aerial through cage, and position to panel.
25.Bend back radio cage retaining tags.
26.Fit radio.
See ELECTRICAL, Repair, radio.
27.Connect battery negative lead.DASH PANEL ASSEMBLY
Service repair no - 76.46.23
Remove
1.Move front seats to rearmost position.
2.Disconnect battery negative lead.
3.Disconnect air bag multiplugs under dash panel.
CAUTION: When air bags are fitted,
reference must be made to the Airbag
Supplementary Restraint System section.
4.Remove passenger glove box.
5.Remove driver's side access panel.
6.Remove centre console assembly.
See centre
console.
7.Remove airbag from steering wheel.See
SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, driver's airbag module.
8.Remove passenger's airbag from dash panel.
See SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, passenger's airbag module.
9.Release clamp and lower steering column.
10.Remove steering wheel.
See STEERING,
Repair, steering wheel.
11.Remove column switch.See
SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, column switch assembly.
12.Remove instrument binnacle.See
ELECTRICAL, Repair, instrument binnacle.
13.Remove radio.See ELECTRICAL, Repair,
radio.
14.Remove exterior mirrors switch panel.
15.Remove coin tray.
16.Remove switch panel.
17.Remove clock.
18.Undo screw securing mounting bracket and
position passenger's side relay assembly aside.
19.Set heater controls fully clockwise.

CHASSIS AND BODY
49
REPAIR Refit
CAUTION: When refitting avoid trapping
electrical wiring.
29.Reverse removal procedure.
30.With assistance: Position dash panel and
connect dash harness multiplugs to fusebox and
main harness.
31.Reverse removal procedure. Ensure dash panel
upper bracket studs are located before the 4
lower brackets.
32.Reverse removal procedure. Disconnect
glovebox switch Lucars to ease fitting of relay
bracket.WINDSCREEN GLASS
Service repair no - 76.81.01
Information
The following equipment is required:
·Cutting wire and handles
·Windscreen repair kit (see Technical
Bulletin).
See Electrical Trouble Shooting
Manual.Windscreen Glass Replacement.
·Sealant applicator gun.
·Suction cup lifters.
The following materials are included in the windscreen
repair kit:
·Glass cleaning solvent - 'Betawipe' Glass
activator (yellow cap).
·Cotton buds.
·Glass primer - 'Betaprime'(green cap).
·Body primer - 'Betaprime' paint/plastic
primer (red cap).
·Betaseal Adhesive sealant.
NOTE: The adhesive sealant cures in 6 to 8
hours
CAUTION: Once existing sealant is cut, the
exposed surfaces oxidises in
approximately 90 minutes. The refit
procedure must be completed within this time
span to prevent the sealant oxidising, to effect a
satisfactory joint.
CAUTION: If the windscreen aperture body
flange shows signs of corrosion it must be
treated with anti corrosion primer and
repainted. Newly painted areas must then be left
for 8 hours or more before applying adhesive
sealant.

CHASSIS AND BODY
53
REPAIR
31. With assistance:Attach suction cups to glass
and lift into position, carefully align the indicators
on the obscuration band with the supports.
Lower screen onto body flange, check alignment
and firmly press to seat glass in the aperture.
NOTE: The finisher on later vehicles will
not have cutouts, or supports fitted, as
shown.
32.Align cut outs with the supports and push
finisher fully onto the glass. Use a wooden block
to ensure fit.
33.Refit 'A' post finishers and interior mirror.
34.Refit wiper arms.FRONT SEAT - ELECTRIC
Service repair no - 76.77.01
Remove
1.Operate controls to adjust seat fully backwards
and remove 2 bolts securing seat slides.
2.Operate controls to adjust seat fully forwards.
3.Remove 3 studs securing seat side valance.
4.Remove side valance.