engine LAND ROVER DISCOVERY 1995 Owner's Guide

GENERAL FITTING REMINDERS
5
INFORMATION JOINTS AND JOINT FACES
1.Always use correct gaskets where they are
specified.
2.Use jointing compound only when
recommended. Otherwise fit joints dry.
3.When jointing compound is used, apply in a thin
uniform film to metal surfaces; take great care to
prevent it from entering oilways, pipes or blind
tapped holes.
4.Remove all traces of old jointing materials prior
to reassembly. Do not use a tool which could
damage joint faces.
5.Inspect joint faces for scratches or burrs and
remove with a fine file or oil stone; do not allow
removed material or dirt to enter tapped holes or
enclosed parts.
6.Blow out any pipes, channels or crevices with
compressed air, fit new 'O' rings or seals
displaced by air blast.FLEXIBLE HYDRAULIC PIPES, HOSES
1.Before removing any brake or power steering
hose, clean end fittings and area surrounding
them as thoroughly as possible.
2.Obtain appropriate plugs or caps before
detaching hose end fittings, so that ports can be
immediately covered to exclude dirt.
3.Clean hose externally and blow through with
airline. Examine carefully for cracks, separation
of plies, security of end fittings and external
damage. Reject any hose found faulty.
4.When refitting hose, ensure that no unnecessary
bends are introduced, and that hose is not
twisted before or during tightening of union nuts.
5.Containers for hydraulic fluid must be kept
absolutely clean.
6.Do not store brake fluid in an unsealed
container. It will absorb water, and fluid in this
condition would be dangerous to use due to a
lowering of its boiling point.
7.Do not allow brake fluid to be contaminated with
mineral oil, or use a container which has
previously contained mineral oil.
8.Do not re-use brake fluid bled from system.
9.Always use clean brake fluid to clean hydraulic
components.
10.Fit a cap to seal a hydraulic union and a plug to
its socket after removal to prevent ingress of dirt.
11.Absolute cleanliness must be observed with
hydraulic components at all times.
12.After any work on hydraulic systems, inspect
carefully for leaks underneath the vehicle while a
second operator applies maximum pressure to
the brakes (engine running) and operates the
steering.

LUBRICANTS, FLUIDS AND CAPACITIES
1
INFORMATION RECOMMENDED LUBRICANTS AND FLUIDS -
USA VEHICLES
AMBIENT TEMPERATURE°C
COMPONENT SPECIFICATION VISCOSITY -30 -20 -10 0 10 20 30 40 50
Engine Use oils to API 5W/20 )
service level
SGSH 5W/30 )
or 5W/40 )
RES.22.OL.G4
or
CCMC G4 10W/30
10W/40 )
10W/50 )
15W/40 )
15W/50 )
20W/40 )
20W/50 )
Automatic gearbox ATF Dexron IID
Final drive units API or GL5 90 EP
Swivel pin housings MIL - L - 2105 or
MIL - L - 2105B, C
or D 80W EP
Power steering ATF Dexron IID
LT 230T API GL4 or GL5
transfer gearbox MIL - L - 2105 or
MIL - L - 2105B
Brake reservoir Brake fluid must have a minimum
boiling point of 260°C (500ÊF) and
comply with FMVSS/116/DOT 4
Lubrication nipples
(hubs, ball joints,
etc.)NLGI-2 multipurpose lithium based
grease
See table on page 3 for remaining vehicle components

09LUBRICANTS, FLUIDS AND CAPACITIES
2
INFORMATION RECOMMENDED LUBRICANTS AND FLUIDS
All climates and conditions
AMBIENT TEMPERATURE°C
COMPONENT SPECIFICATION VISCOSITY -30 -20 -10 0 10 20 30 40 50
Petrol modelsOils must meet: 5W/30
Engine sump
RES.22.OL.G-4 5W/40
or 5W/50
CCMC G-4 or 10W/30
API SG or SH 10W/40
10W/50
15W/40
15W/50
20W/40
20W/50
25W/40
25W/50
DieselRES.22.OL.PD-2 15W/40
Engine sump or CCMC PD-2
or API CD
Main Gearbox
AutomaticATF Dexron IID
Main Gearbox
manualATF Dexron IID
Final drive units API or GL5 90 EP
Swivel pin housings MIL - L - 2105 or
MIL - L - 2105B 80 EP
CorD
Power steering ATF Dexron IID
Transfer box API GL4 or GL5 90 EP
LT230T MIL - L - 2105 or
MIL - L - 2105B 80 EP
CorD

LUBRICANTS, FLUIDS AND CAPACITIES
3
INFORMATION Propeller shaft Front
and RearNLGI - 2 Multi-purpose Lithium based GREASE
Lubrication nipples
(hubs, ball joints
etc.)
Seat slides
Door lock striker
Brake and clutch
reservoirsBrake fluids having a minimum boiling point of 260°C (500°F) and complying with
FMVSS 116 DOT4
Engine coolant Use an ethylene glycol based anti-freeze (containing no methanol)
V8i, Tdi, Mpi with non-phosphate corrosion inhibitors suitable for use in aluminium engines to ensure
the protection of the cooling system against frost and corrosion in all seasons. Use one
part anti-freeze to one part water for protection down to -36°C (-33°F).
IMPORTANT: Coolant solution must not fall below proportions one part
anti-freeze to three parts water, i.e. minimum 25% anti-freeze in coolant otherwise
damage to engine is liable to occur. Or a maximum of 60%.
Battery lugs, Petroleum jelly.
Earthing surfacesNOTE: Do not use Silicone Grease
where paint has
been removed
Air Conditioning
System Refrigerant Use only refrigerant R134a
Compressor Oil Nippon Denso ND-oil8 Unipart ND-oil8
ABS Sensor Silicone grease: Staborags NBU - Wabco 830 502,0634
bush-rear Wacker chemie 704 - Wabco 830 502,0164
Kluber GL301
LUBRICATION PRACTICE
Use a high quality oil of the correct viscosity range and service classification in the engine during maintenance and
when topping up. The use of oil not to the correct specification can lead to high oil and fuel consumption and
ultimately to damaged components.
Oil to the correct specification contains additives which disperse the corrosive acids formed by combustion and
prevent the formation of sludge which can block the oilways. Additional oil additives should not be used. Always
adhere to the recommended servicing intervals.
WARNING: Many liquids and other substances used in motor vehicles are poisonous. They must
not be consumed and must be kept away from open wounds. These substances, among others,
include anti-freeze windscreen washer additives, lubricants and various adhesives.

09LUBRICANTS, FLUIDS AND CAPACITIES
4
INFORMATION CAPACITIES
The following capacity figures are approximate and are provided as a guide only.
Capacities (approx.)* Litres Imp.Unit US unit
Engine sump oil
- 300Tdi models 5,8...................................................... 10.20 pt 12.30 pt
- V8i petrol models 3.9 6,1............................................ 10.70 pt 12.90 pt
- Mpi petrol models 4,90.................................................. 8.70 pt 10.40 pt
Extra when refilling after fitting new filter
- 300Tdi models 0,85...................................................... 1.50 pt 1.80 pt
- V8i petrol models 0,56.................................................. 1.00 pt 1.20 pt
- Mpi 0,4........................................................................ 0.70 pt 0.85 pt
Manual gearbox 2,67............................................................... 4.70 pt 5.70 pt
Automatic gearbox 9,1........................................................... 16.00 pt 19.20 pt
Transfer gearbox oil 2,30......................................................... 4.00 pt 4.90 pt
Front differential 1,70............................................................... 3.00 pt 3.60 pt
Rear differential 1,70................................................................ 3.00 pt 3.60 pt
Power steering box and reservoir LHD 2,90............................ 5.00 pt 6.00 pt
Power steering box and reservoir RHD 3,40............................ 6.00 pt 7.20 pt
Swivel pin housing oil (each) 0,35............................................ 0.60 pt 0.75 pt
Fuel tank usable fuel 89,0........................................................ 19.5 gall 23 gall
Cooling system
- 300Tdi models 11,50...................................................... 20.20 pt 24.30 pt
- V8i petrol models 11,30.................................................. 20.00 pt 23.90 pt
- Mpi 10,00........................................................................ 17.60 pt 21.00 pt
Washer bottle 7,0................................................................... 12.30 pt 14.80 pt
NOTE: * All levels must be checked by dipstick or level plugs as applicable. When draining oil
from the ZF automatic gearbox, oil will remain in the torque converter, refill to high level on
dipstick only.

LUBRICANTS, FLUIDS AND CAPACITIES
5
INFORMATION ANTI-FREEZE
ENGINE TYPE MIXTURE STRENGTH PERCENTAGE PROTECTION
CONCENTRATION LOWER
TEMPERATURE
LIMIT
V8i Engine One part anti-freeze
Diesel Engine One part water 50%
Complete protection-33°F
Vehicle may be driven away immediately from cold - 36°C
Safe limit protection-41°C
Coolant in mushy state. Engine may be started and driven away after warm-up
period-42°F
Lower protection-47°C
Prevents frost damage to cylinder head, block and radiator. Thaw out before
starting engine-53°F
CAUTION: Anti-freeze content must never be allowed to fall below 25% otherwise damage to the
engine is liable to occur. Also, anti-freeze content should not exceed 60% as this will greatly
reduce the cooling effect of the coolant.
FUEL REQUIREMENTS
Catalyst vehicles
Vehicles equipped with catalytic converter are designed to use ONLY unleaded fuel. Unleaded fuel must be used
for the emission control system to operate properly. Its use will also reduce spark plug fouling, exhaust system
corrosion and engine oil deterioration.
Using fuel that contains lead will result in damage to the emission control system and could result in loss of
warranty coverage. The effectiveness of the catalysts in the catalytic converters will be seriously impaired if leaded
fuel is used. The vehicle is equipped with an electronic fuel injection system, which includes two oxygen sensors.
Leaded fuel will damage the sensors, and will deteriorate the emission control system.
Regulations require that pumps delivering unleaded fuel be labelledUNLEADED.Only these pumps have nozzles
which fit the filler neck of the vehicle fuel tank.

09LUBRICANTS, FLUIDS AND CAPACITIES
6
INFORMATION RECOMMENDED FUEL
Petrol engines
- with catalytic converter unleaded only, 95 RON (USA 90 CLC or AKI)................................................
- non catalytic, 9.35:1 compression ratio leaded 97 RON/unleaded 95 RON.......................
- non catalytic, 8.13:1 compression ratio leaded 90 RON/unleaded 95 RON.......................
- Australia minimum 91 RON unleaded......................................................................
Diesel engines
300Tdi Diesel fuel oil,distillate,diesel fuel, automotive gas or...........................................................................
Derv to British standard 2869, Class A1 or A2
Using fuel with an octane rating lower than stated above could seriously impair vehicle performance.
CAUTION: Do not use oxygenated fuels such as blends of methanol/ gasoline or ethanol/gasoline
(e.g. 'Gasohol'). Take care not to spill fuel during refuelling.

10MAINTENANCE
4
MAINTENANCE UNDER BONNET [HOOD] MAINTENANCE
CHECK COOLING/HEATER SYSTEMS
Check cooling/heater systems for leaks and hoses for
security and condition.
Cooling system hoses should be changed at first
signs of deterioration.
CHECK CONDITION OF ENGINE MOUNTING
RUBBERS
CHECK BRAKE SERVO HOSE FOR SECURITY
AND CONDITION
CHECK FUEL EVAPORATIVE LOSS CONTROL
SYSTEM FOR LEAKS - V8i CATALYST, Mpi
CHECK FUEL FILLER CAP SEAL FOR LEAKS - V8i
- CATALYST, Mpi
CHECK CONDITION OF HEATER PLUG WIRING
FOR FRAYING, CHAFING AND DETERIORATION -
Tdi
CHECK IGNITION WIRING
Check ignition wiring and high tension leads for
fraying, chafing and deterioration.
CLEAN DISTRIBUTOR CAP - V8i
The electronic ignition employs a Lucas 35DLM8
distributor.
Internal operating parts of distributor are pre-set at
factory and do not normally require resetting.
Adjustments should only be made if unit is known to
be faulty or damaged. Distributor maintenance
consists of following items.
1.Clean outer surfaces of distributor cap to remove
dirt, grease etc.
2.Unclip cap, check cap for cracks.
3.Wipe inside cap with lint free cloth.
4.Check rotor arm, cap and flash shield tracking.
DO NOT DISTURB clear plastic insulating
cover (flash shield) which protects magnetic
pick-up module.
LUBRICATE DISTRIBUTOR ROTOR SPINDLE - V8i
Apply a spot of clean engine oil into rotor spindle after
rotor arm has been removed.
CLEAN/ADJUST SPARK PLUGS - V8i CATALYST
RENEW SPARK PLUGS V8i - V8i CATALYST
Clean, adjust and renew
1.Take great care when fitting spark plugs not to
cross-thread plug, otherwise costly damage to
cylinder head will result.

MAINTENANCE
5
MAINTENANCE 2.Clean or replace spark plugs as applicable.
3.It is essential that correct type of spark plugs are
fitted.
4.Incorrect grade of plugs may lead to piston
overheating and engine failure.
Remove
5.Disconnect battery negative lead. Remove H.T.
leads from spark plugs.
6.Remove plugs and washers.
7.When pushing leads onto plugs, ensure that
shrouds are firmly seated.Fitting H.T. leads
8.Ensure replacement H.T. leads are correctly
refitted as illustrated.
Failure to observe this instruction may result in
cross-firing between two closely fitted leads
which are consecutive in firing order.
3.9 V8
4.0 V8

MAINTENANCE
7
MAINTENANCE
CHECK/ADJUST VALVE CLEARANCES. - Tdi
Valve adjustment.See GENERAL SPECIFICATION
DATA, Information, 300 Tdi Engine
RENEW FUEL FILTER ELEMENT - Tdi
Drain off water and sediment
CAUTION: It is essential that any water
and sediment in fuel filter is drained off, as
water in fuel can result in damage to
injection pump.
1.Hold a small receptacle beneath drain cock.
Unscrew the drain cock half a turn.
2.Drain off water and sediment.
3.Tighten the drain cock immediately fuel starts to
flow from drain cock.
NOTE: Any delay in tightening drain cock
when fuel starts to flow could possibly
mean bleeding fuel system.
Renew fuel filter element
1.Clean area around filter, place a container
beneath.
2.Unscrew filter, a quantity of fuel will be released,
and discard filter.
3.Wet seal of new filter with fuel.
4.Screw new filter into position.
5.Ensure that drain cock is secure.
RENEW AIR CLEANER ELEMENT V8i CATALYST
Mpi - Tdi - V8i NON CATALYST
To renew air cleaner element - V8i, Mpi,Tdi
See FUEL SYSTEM, Repair, Air Cleaner