tow LAND ROVER DISCOVERY 1995 Owner's Guide

76CHASSIS AND BODY
12
REPAIR REAR DOOR TRIM PANEL
Service repair no - 76.34.09
Remove
1.Remove the two screws securing the door pull
and remove it from the door.
2.Remove the finisher from the inner door handle.
3.Using a trim panel removing tool release the
seventeen trim panel fasteners and withdraw the
panel from the door.
4.If necessary remove the sixteen screws securing
the stowage bins to the trim panel and detach
the bins.
Refit
5.Reverse removal procedure.REAR DOOR LOCK AND INNER AND OUTER
RELEASE HANDLES
Service repair no - 76.37.16/74/77/78
Remove
1.Disconnect battery negative lead.
2.Remove the door pull, the trim panel and the
vapour protective sheet, to allow access to the
door handles and lock mechanisms.
3.Disconnect the inner release handle connecting
rod at the lock.
4.Remove the two screws securing the inner
handle and withdraw the handle complete with
connecting rod.
NOTE: Two identical 'Y' shaped levers
(bellcranks) are fitted to the rear door lock
mechanism and are referred to as inner
and outer 'Y' levers; the inner one being the
nearest to the inner door panel.
5.If fitted, remove the central locking actuator
control rod link from the actuator and from the
inner 'Y' lever.
6.Detach the remote button connecting rod at the
inner 'Y' lever and withdraw from inside the door.
7.Detach the lock and barrel connecting rods from
the upper leg of the inner 'Y' lever.

CHASSIS AND BODY
27
REPAIR REAR SEAT CUSHION COVER
Service repair no - 76.70.88/89
Remove
NOTE: The procedure for removing both
left and right hand seat cushions is the
same.
1.Remove the rear seat assembly from the
vehicle.
See rear passenger seat.
2.Remove the seat squab.
3.Remove the seat cushion.
4.Remove the cushion base cover retaining
screws and withdraw the cover.
5.Release the seat cover securing clips at the
frame and at the seat belt aperture.
6.Remove the cover from the cushion.
Refit
7.Reverse removal procedure.SPLIT REAR SEAT LOCKING MECHANISM
Service repair no - 76.70.51
Remove
1.Remove the front body side trim casing.
See
front body side trim casing.
2.Remove the three screws securing the latch to
the tower, noting that access to the single screw
is gained through the hole in the front of the
tower.
3.Retrieve the latch from the opening at the rear of
the tower. If necessary retrieve the single screw.
4.The operating rod can be removed from the latch
by releasing it at the plastic clip.
Refit
5.Reverse removal procedure. Setting the release
button to achieve a gap of 5 - 8 mm (3/16 - 5/16
in).

76CHASSIS AND BODY
28
REPAIR REAR FOLD DOWN SEATS
Service repair no - 76.71.23
Seat and squab
Remove
1.Locate the seat in the down position, release the
seat belt strap and buckle from their stowed
positions.
2.Remove 4 Torx screws from the lower brackets.
3.Fold the seat up and remove the 2 Torx screws
from the upper brackets. Collect 4 washers.
4.Remove seat assembly.
Refit
5.Position seat assembly, align upper brackets,
and secure with Torx screws tightened to
13 Nm
(10 lbf ft)
.
NOTE: Ensure washers are fitted in their
correct positions.
6.Align lower brackets, fit Torx screws and tighten
to
13 Nm (10 lbf ft).
7.Secure the seat belt strap and buckle to their
stowed positions.
Seat squab
Remove
8.Remove the seat assembly from the vehicle.
9.Remove the pivot bolts and washers securing
the seat squab to the frame.
NOTE: The pivot bolts, securing the seat
squab and cushion, are fitted with a wavy
washer under the head and a plain washer
between the link or bracket. Ensure that these
washers are fitted in the correct locations when
reassembling the seat.

CHASSIS AND BODY
39
REPAIR SUNROOF ELECTRIC MOTORS
Service repair no - 76.82.84/85
FRONT MOTOR
Remove
1.Disconnect battery negative lead.
2.Ensure sunroof is in normally closed position
NOTE: If the electric motor has failed the
sunroof can be closed manually using an
allen key to turn motor spindle A.
3.Remove switch panel from stowage pocket
panel
4.Remove interior lamp from stowage pocket
panel
5.Remove alarm ultrasonic unit.
6.Unscrew ten fixings and remove stowage pocket
from headlining.
7.Disconnect motor wiring multiplug.
8.Remove three screws and motor.
Refit
9.Reverse removal procedure.
CAUTION: Ensure the motor is aligned
with fixing holes and the sunroof is in the
normally closed position. DO NOT rotate
the motor drive spindle in the rack - this may
result in incorrect operation of the sunroof.REAR MOTOR
Remove
1.Disconnect battery negative lead.
2.Ensure sunroof is in normally closed position
NOTE: If the electric motor has failed the
sunroof can be closed manually using an
allen key to turn motor spindle.
3.Remove headlining.
See headlining.
4.Disconnect motor wiring multiplug.
5.Remove three screws and motor.
Refit
6.Reverse removal procedure.
CAUTION: Ensure the motor is aligned
with fixing holes and the sunroof is in the
normally closed position. DO NOT rotate
the motor drive spindle in the rack - this may
result in incorrect operation of the sunroof.

76CHASSIS AND BODY
40
REPAIR SUNROOF ELECTRIC CONTROL UNIT
Service repair no - 76.82.73
The control unit serves both front and rear sunroofs
and is sited above the front switches behind
headlining.
Remove
1.Disconnect battery negative lead.
2.Ensure sunroof is in normally closed position.
NOTE: If the electric motor has failed the
sunroof can be closed manually using an
allen key to turn motor spindle.
3.Remove switch panel from stowage pocket
panel
4.Remove interior lamp from stowage pocket
panel
5.Remove alarm ultrasonic unit.
6.Unscrew ten fixings and remove stowage pocket
from headlining.
7.Disconnect electric plugs from control unit.
8.Remove two retaining screws and control unit.
Refit
9.Reverse removal procedure.

76CHASSIS AND BODY
42
REPAIR SUNROOF REGULATOR MANUAL
Service repair no - 76.83.03/04
FRONT
Remove
1.Ensure sunroof is in normally closed position.
2.Remove retaining screw and regulator handle.
3.Remove switch panel from stowage pocket
panel
4.Remove interior lamp from stowage pocket
panel
5.Remove alarm ultra sonic unit.
6.Unscrew ten fixings and remove stowage pocket
from headlining.
7.Remove two retaining screws and regulator from
clamping frame.
Refit
8.Reverse removal procedure.
CAUTION: Ensure the regulator is aligned
with fixing holes and the sunroof is in the
normally closed position. DO NOT rotate
the regulator spindle in the rack - this may result
in incorrect operation of the sunroof.REAR
Remove
1.Ensure sunroof is in normally closed position.
2.Remove retaining screw and regulator handle.
3.Remove headlining.
See headlining.
4.Remove two retaining screws and regulator from
clamping frame.
Refit
5.Reverse removal procedure.
CAUTION: Ensure the regulator is aligned
with fixing holes and the sunroof is in the
normally closed position. DO NOT rotate
the regulator spindle in the rack - this may result
in incorrect operation of the sunroof.

76CHASSIS AND BODY
64
REPAIR GRAB HANDLE - TAIL DOOR - WITH REAR AIR
CONDITIONING FITTED
Service repair no - 76.58.35/20
Remove
1.Remove 'E' post trim casing.
See 'E' post trim
casing - lh - with rear air conditioning fitted.
2.Release foam strip from around grab handle
retaining bolts.
3.Remove 4 bolts securing grab handle to body.
4.Remove grab handle.Refit
5.Position grab handle, fit bolts and tighten to
10
Nm (7 lbf ft)
.
6.Secure foam strip to body.
7.Fit 'E' post trim casing.
See 'E' post trim
casing - lh - with rear air conditioning fitted.
HEADLINING - WITH SUN ROOF AND REAR AIR
CONDITIONING FITTED - 5 DOOR
Service repair no - 76.64.14/20
Remove
1.Remove both sun visors.
See sun visor.
2.Remove 4 grab handles.See grab handle.
3.Remove front headlining stowage panel.See
headlining stowage panel - front - with sun
roof fitted.
4.Remove LH alpine light trim casing.See alpine
light trim casing - lh - with rear air
conditioning fitted.
5.Remove RH alpine light trim casing.See alpine
light trim casing.
6.Release LH and RH sun visor clip retaining
screw covers.
7.Remove LH and RH sun visor clip retaining
screws.
8.Remove LH and RH clips.

76CHASSIS AND BODY
66
REPAIR
15.Release LH and RH, 'A' post trim finishers from
uppermost retaining clips.
16.With assistance, release headlining from LH and
RH, 'A', 'B' and 'D' post finishers.
17.Remove headlining assembly.Dismantle
18.Remove 22 nuts securing headlining stowage
nets and rear headlining panel.
19.Remove stowage nets and headlining panel.
20.Collect 7 mounting plates.
Rebuild
21.Position stowage nets and headlining panel, fit
mounting plates to studs and secure with nuts.
Refit
22.With assistance, fit headlining and position to LH
and RH, 'A', 'B' and 'D' post finishers.
23.Secure LH and RH, 'A' post trim finisher
retaining clips.
24.Fit rear sun roof aperture seal.
25.Fit and tighten screw securing rear headlining
panel to body.
26.Position vents to headlining, attach clips to vents
and secure to headlining.
27.Position rear sun roof switch, connect multiplug
and secure to headlining panel.
28.Position rear passenger interior lamp, connect
multiplug and secure to headlining panel.
29.Fit front sun roof aperture seal.
30.Fit LH and RH sun visor retaining clips to body.
31.Fit and tighten screws securing sun visor
retaining clips and secure screw covers.
32.Fit RH alpine light trim casing.
See alpine light
trim casing.
33.Fit LH alpine light trim casing.See alpine light
trim casing - lh - with rear air conditioning
fitted.
34.Fit front headlining stowage panel.See
headlining stowage panel - front - with sun
roof fitted.
35.Fit grab handles.See grab handle.
36.Fit sun visors.See sun visor.

CHASSIS AND BODY
67
REPAIR ASH TRAY - DASH PANEL CENTRAL LOUVRE
PANEL
Service repair no - 76.67.26
Remove
1.Open ash tray.
2.Press release catch and remove ash tray.
Refit
3.Fit ash tray.HEADLINING STOWAGE PANEL - FRONT - WITH
SUN ROOF FITTED
Service repair no - 76.67.27
Remove
1.Remove 10 screws securing stowage panel to
body.
2.Release panel and disconnect Lucar and 4
multiplugs.
3.Remove stowage panel assembly.

76CHASSIS AND BODY
68
REPAIR Dismantle
4.Remove interior lamp lens.
5.Remove 2 nuts securing lamp to stowage panel.
6.Remove lamp.
7.Remove alarm volumetric sensor/blanking plate.
8.Remove electric sun roof switch pack.
9.Remove electric sun roof manual opening plug.
Rebuild
10.Fit electric sun roof manual opening plug to
panel.
11.Fit alarm volumetric sensor.
12.Fit electric sun roof switch pack to panel.
13.Fit interior lamp to panel and secure with nuts.
14.Fit interior lamp lens.
Refit
15.Position stowage panel assembly and connect
Lucar and multiplugs.
16.Align panel to headlining and secure with
screws.REAR FOLD DOWN SEAT BELTS - LH WITH REAR
AIR CONDITIONING FITTED
Service repair no - 76.73.28/20
Remove
1.Locate the seat in the down position, remove the
seat belt strap and buckle from their stowed
positions.
2.Remove seat belt strap and buckle retaining bolt
covers.
3.Remove bolts securing strap and buckle.
4.Remove seat belts and collect spacers.
Refit
5.Fit spacers to seat belt retaining bolts, position to
fixings and tighten to
32 Nm (24 lbf ft).
6.Fit seat belt retaining bolt covers.
7.Secure seat belt strap and buckle to their stowed
positions and position seat in the up position.