brake LAND ROVER DISCOVERY 1995 Repair Manual

30MANIFOLD AND EXHAUST SYSTEM
10
REPAIR 10.Release clip and disconnect breather hose from
manifold.
11.Release 2 bolts securing camshaft cover
brackets to manifold.
12.Disconnect 4 vacuum hoses from manifold.
13.Remove 6 bolts securing manifold chamber to
lower manifold.
14.Remove manifold chamber and collect gaskets.
Refit
NOTE: For torque values.See
Specifications, torque, Torque Values
15.Ensure mating faces of manifold chamber and
lower manifold are clean.
16.Fit a new gasket, position manifold chamber to
lower manifold.
17.Fit bolts, tighten to the correct torque.
18.Connect vacuum hoses to manifold.
19.Position camshaft cover brackets to manifold,
secure with bolts.
20.Connect breather hose and brake servo hose to
manifold, secure with clips.
21.Connect multiplug to fuel temperature sensor.
22.Connect breather hose to throttle housing and
secure with clip.
23.Connect throttle cable to cam and secure to
abutment bracket.
24.Connect coolant bypass hose to throttle housing.
25.Connect stepper motor and throttle
potentiometer multiplugs.
26.Connect air cleaner hose to throttle housing and
secure with clip.
27.Reconnect battery negative lead.
28.Adjust throttle cable.

R380
1
REPAIR R380 MANUAL GEARBOX
Service repair no - 37.20.02
Remove
WARNING: Where the use of a
transmission hoist is necessary, it is
absolutely essential to follow the
manufacturer's instructions to ensure safe and
effective use of equipment.
1.Install vehicle on a ramp [hoist].
2.Disconnect battery earth lead.
3.Remove centre console.
See CHASSIS AND
BODY, Repair, Centre Console
4.Remove sound insulation from top of
transmission tunnel.
5.Remove bolt and remove upper gear lever.
6.Remove screws securing gear selector lever and
high/low selector lever draft excluders.
7.Remove draft excluder clamp rings.
8.Remove handbrake cable clevis pin clip and
clevis pin.
9.Remove 'C' clip and cable adjuster.
10.Select low range to prevent gear lever fouling
tunnel when removing gearbox.
11.Remove bolt securing gearbox breather pipe clip
to cylinder block.
12.Remove bolts securing fan cowl to radiator.
13.Release fan cowl from radiator and lay over fan
blades.
14.Raise ramp [hoist].
15.Drain oil from main gearbox and transfer
gearbox.
See SECTION 10, Maintenance,
Under Vehicle Maintenance
16.Remove exhaust front pipe(s).See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
System Complete
17.Release intermediate exhaust pipe(s) from
mountings and tie aside.
18.Remove bolts securing clutch slave cylinder.
19.Release slave cylinder from clutch housing and
collect spacer.
20.Mark propeller shaft drive flange relationships for
reassembly.
21.Disconnect front and rear propeller shafts from
transfer gearbox. Tie shafts aside.
22.Remove clamp and disconnect speedometer
cable from transfer gearbox.
23.Release handbrake cable from transmission
tunnel.
24.Temporarily support transmission in a way which
enables the crossmember to be removed and a
hoist cradle to be fitted.

R380
3
REPAIR Assembling transfer gearbox to main gearbox
45.Clean extension housing and transfer gearbox
mating faces.
46.Ensuring loose upper dowel is fitted, hoist
transfer gearbox into position.
47.Fit and tighten nut and bolts to
34Nm.
48.Connect high/low operating rod, fit and tighten
locknut.
49.Fit link to differential lock lever and secure with 2
clips
50.Align lever to high/low shaft, position washer, fit
bolt and new Nyloc nut. Tighten to
2Nm.
51.Position breather pipes, secure pipe unions
using new sealing washers. Tighten unions to
15Nm.
Fitting transfer gearbox and main gearbox
assembly to engine
52.Position transmission assembly to hoist cradle.
53.Clean bell housing and engine mating faces.
54.Temporarily fit gear lever and select any gear in
main gearbox to facilitate entry of gearbox input
shaft.
55.Position and raise hoist, and fit transmission to
engine whilst keeping wires and pipes clear to
prevent trapping.
56.Fit and tighten nuts securing transmission to
engine.
57.Connect reverse lamp switch connectors and
differential lock switch connectors.
58.Secure breather pipes to harness with clips.
59.Position temporary support.
60.Remove 2 bolts securing lifting cradle to
transmission and remove hoist. Apply Loctite
290 to bolts and refit bolts.
61.Position cross-member, loosely fit nuts and bolts
securing cross-member mountings to
transmission.62.Raise transmission, align cross-member and
loosely fit nuts and bolts securing cross-member
to chassis.
63.Tighten all securing nuts and bolts. Remove
supporting jack from under sump.
64.Remove temporary support.
65.Fit handbrake cable through transmission tunnel
and secure gaiter.
66.Connect speedometer cable to transfer gearbox.
67.Line up marks and connect front and rear
propeller shafts.
68.Clean spacer, clutch slave cylinder and gearbox
mating faces.
69.Position spacer and slave cylinder, fit bolts.
Tighten to
25Nm.
70.Untie intermediate exhaust pipe(s) and refit
exhaust front pipe(s).
See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust System
Complete
71.Refill main gearbox and transfer gearbox with oil.
See SECTION 10, Maintenance, Under
Vehicle Maintenance
72.Lower ramp [hoist].
73.Fit fan cowl, fit and tighten bolts.
74.Align breather pipe clip to cylinder block, fit and
tighten bolts.
75.Fit handbrake cable adjuster and secure with 'C'
clip.
76.Align cable trunnion to handbrake lever, fit clevis
pin and secure with clip.
77.Check handbrake adjustment.
See SECTION
10, Maintenance, Vehicle Interior
78.Fit upper gear lever, fit and tighten bolt.
79.Fit gear selector lever and high/low selector
lever draft excluders.
80.Position draft excluder clamp rings, fit and
tighten screws.
81.Refit sound insulation.
82.Refit centre console.
See CHASSIS AND
BODY, Repair, Centre Console
83.Connect battery earth lead.

41TRANSFER GEARBOX
2
REPAIR Remove
1.Site vehicle on a ramp [hoist].
2.Disconnect battery negative lead.
3.Remove fan cowl from radiator.
4.Remove transfer gear lever knob and gaiter.
5.Raise vehicle on ramp [hoist].
6.Drain oil and refit plug.
7.Detach heat shield at front exhaust pipe to
manifold.
8.Disconnect electrics to Lambda sensors.
9.Remove catalytic converter assembly.
10.Remove chassis crossmember from under
gearbox.
11.Remove heat shield from speedometer cable at
transfer gearbox.
12.Remove clamp and disconnect speedometer
cable from transfer gearbox. Tie cable to one
side.
13.Mark for reassembly then disconnect propeller
shaft to output flange, tie to one side.
14.Repeat on front propeller shaft to output flange.
15.Remove bolts retaining silencer front and rear
securing brackets and tie silencer to one side.
16.Place four 30mm long spacers between top of
hoist and adaptor plate, at securing points, and
secure adaptor plate to hoist.17.Remove four central bolts from transfer gearbox
bottom cover, move hoist into position and
secure adaptor plate to transfer gearbox.
18.Adjust hoist to take weight of transfer gearbox.
19.Remove tie bar, transfer gearbox to main
gearbox.
20.Remove nuts and bolts securing right transfer
gearbox mounting bracket to chassis.
21.Repeat for left mounting bracket. Removal of
these fixings will also free speedometer
transducer bracket.
22.Remove right side mounting bracket to flexible
mounting rubber.
23.Lower hoist until rear brake drum clears
passenger footwell. Check engine does not
crush any components while lowering.
24.Loosen park brake adjustment nut.
25.Remove park brake drum.
26.Remove park brake assembly complete from
rear output flange.
27.Disconnect leads from transfer gearbox
temperature sensor and differential lock warning
light switch.
28.Remove banjo bolt from breather pipe, retrieve
sealing washers and lay pipe aside.
29.Remove split [cotter] pin and washers securing
differential lock to connecting rod and disconnect
rod from lever.
30.Select low range transfer gearbox position.
31.Remove high/low rod lower lock nut and remove
rod from yoke.
32.Position hoist jack channel under bell housing.
33.Using wooden block support the main gearbox
and bell housing.
34.Remove upper and lower bolts securing transfer
gearbox to main gearbox.
35.Fit guide studs 18G 1425 to main gearbox and
move transfer gearbox rearwards to detach.

TRANSFER GEARBOX
3
REPAIR Refit
36.Select 'P' in main gearbox, with low range and
differential lock selected in transfer gearbox.
37.Secure transfer gearbox to adaptor plate on
lifting hoist.
38.Ensure joint faces of transfer and main
gearboxes are clean and guide studs 18G 1425
are fitted.
39.Raise hoist until transfer gearbox can be located
over guide studs to main gearbox. At the same
time locate high/low lower link to yoke.
40.Remove guide studs and secure transfer
gearbox to main gearbox.41.Complete refitting by reversing removal
procedure, noting the following important points.
42.After removal of adaptor plate from transfer
gearbox, clean threads of four bottom cover
bolts, coat threads with Loctite 290 and fit
together with spring washers. Tighten to
25Nm
43.Add correct grade of oil to transfer gearbox to oil
level plug hole.
See LUBRICANTS, FLUIDS
AND CAPACITIES, Information,
Recommended Lubricants and Fluids
44.Check main gearbox oil level.
45.Check operation of parking brake and adjust as
necessary.
See SECTION 10, Maintenance,
Vehicle Interior

TRANSFER GEARBOX
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
LT230T Transfer gearbox
Pinch bolt - operating arm to crank arm 9......................................................
End cover gear change housing 9.................................................................
Bottom cover to transfer case 25....................................................................
Front output housing to transfer case 25........................................................
Cross shaft housing to front output housing 25...............................................
Gear change housing 25.................................................................................
Pivot shaft to link arm 25.................................................................................
Connecting rod to adjustable clevis 25...........................................................
Anti-rotation plate intermediate shaft 25.........................................................
Front output housing cover 25........................................................................
Pivot bracket to extension housing 25............................................................
Finger housing to front output housing 25......................................................
Bearing housing to transfer case 25...............................................................
Brake drum to coupling flange 25...................................................................
Bearing housing cover to transfer gearbox 45................................................
Rear output speedometer housing to transfer gearbox 45..............................
Selector finger to cross shaft high/low 25.......................................................
Selector fork, high/low to shaft 25...................................................................
Transmission brake to speedometer housing 72............................................
Gate plate to grommet plate 9.......................................................................
Gearbox to transfer case 45...........................................................................
Oil drain plug 30..............................................................................................
Oil filler/level plug 30.......................................................................................
Differential case (front to rear) 60...................................................................
Output flanges 162...........................................................................................
Differential case rear stake nut 72..................................................................
Transfer breather 15.......................................................................................
Transfer box front drive flange to drive shaft 45..............................................
Transfer box rear drive flange to drive shaft 45..............................................
Transfer gearbox mounting brackets to chassis 30........................................
Mounting brackets to transfer gearbox 55......................................................
Mounting rubbers to mounting brackets 21.....................................................
Shiftlock
Shiftlock screws 9..........................................................................................
Neutral switch 25............................................................................................

44AUTOMATIC GEARBOX
10
FAULT DIAGNOSIS FAULT SYMPTOMS
SYMPTOM 1 - Intermittent drive and high pitched
noise
FAULT - Low fluid level or restricted filter
SYMPTOM 2 - No drive in reverse
Select 'D'
ú No drive
FAULT - Continue with Symptom 3
ú Drives forward
FAULT - Reverse gear interlock valve
seized
Select '1'
ú No engine braking
FAULT - Clutch brake 3
SYMPTOM 3 - No drive from rest with 'D' selected
Select '1'
ú Vehicle drives
FAULT - No 2 freewheel
ú No drive
Carry out main line pressure check
ú Normal pressure
FAULT - Clutch A
ú No pressure
FAULT - Blocked filter or pump failure
ú Low pressure
FAULT - Restricted filter or sticking primary
regulator
SYMPTOM 4 - Slip in all forward gears
Carry out main line pressure check
ú No pressure
FAULT - Blocked filter or pump failure
ú Low pressure
FAULT - Restricted filter or sticking primary
regulator
ú Normal pressure
FAULT - Clutch 'A'SYMPTOM 5 - Harsh engagement 'N' to 'D'
Check engine idle speed
Carry out main line pressure check
ú High pressure
FAULT - Primary regulator stuck
ú Normal pressure
FAULT - Clutch 'A' or damper for clutch'A'
SYMPTOM 6 - Fierce shift or flare 1st to 2nd shift
Check engine idle speed
Carry out mainline pressure check
ú High pressure
FAULT - Continue with symptom 5
ú Normal pressure
FAULT - Modulator valve or dampers for
clutch brake CB1 and/or clutch brake CB2
FAULT - Clutch brake CB1 and/or clutch
brake CB2
SYMPTOM 7 - Fierce shift or flare 2nd to 3rd
Carry out mainline pressure check
ú High pressure
FAULT - Continue with symptom 5
ú Normal pressure
FAULT - Modulator valve or clutch 'B'
damper
FAULT - Clutch 'B'
SYMPTOM 8 - No 3rd gear
FAULT - 2-3 shift valve
FAULT - Clutch 'B'
SYMPTOM 9 - No 4th gear 'D' selected
FAULT - 4th to 3rd downshift valve stuck or
3rd to 4th upshift valve stuck
FAULT - Clutch brake 4

ZF
11
FAULT DIAGNOSIS SYMPTOM 10 - None or harsh engagement of
direct drive clutch
NOTE: The direct drive clutch will only
engage if 4th gear is engaged at 40 to 45
mph.
Carry out road test pressure check with gauge
connected to torque converter.
ú Normal pressure
FAULT - Failed direct drive clutch
ú Pressures correct but remains high
FAULTS POSSIBLE -
Direct drive clutch and torque converter
control valve stuck
Hysteresis valve stuck
Direct drive clutch control valve stuck
SYMPTOM 11 - Direct drive clutch shift point
incorrect or at low speed
NOTE: Direct drive clutch engagement at
low speed will cause vibration in the
torque converter
Carry out mainline and torque converter pressure
check
ú Normal pressure
FAULT - Governor valve sticking
ú Low or incorrect pressure
FAULTS POSSIBLE -
Direct drive clutch and torque converter
control valve sticking.
Hysteresis valve stuck.
Direct drive clutch control valve stuck.
SYMPTOM 12 - Drives in 'D' but immediately
upshifts to 3rd
FAULT - 2nd to 3rd shift valve stuck.
SYMPTOM 13 - With 'D' selected vehicle starts in
2nd
FAULTS POSSIBLE -
1st and 2nd shift valve stuck.
Governor sleeve sticking.
SYMPTOM 14 - With 'D' selected vehicle starts in
3rd
FAULTS POSSIBLE -
1st to 2nd and 2nd to 3rd shift valves stuck.
Governor sleeve sticking.SYMPTOM 15 - No kickdown 4th to 3rd
FAULT - 4th to 3rd kickdown valve stuck.
SYMPTOM 16 - Upshifts/downshifts and kickdown
shifts at incorrect road speeds
Check throttle kickdown cable adjustment
Carry out main line pressure check
ú Normal pressure
FAULT - Governor valve sticking
ú Incorrect pressure
FAULTS POSSIBLE -
Incorrect throttle valve adjustment
Primary regulator sticking
SYMPTOM 17 - No upshifts at light throttle
FAULTS POSSIBLE
Governor valve sticking
Shift valves sticking
SYMPTOM 18 - No engine braking '3' selected 3rd
gear
FAULT - Clutch 'C'
SYMPTOM 19 - Delayed or no downshift occurs
when making a manual selection from '3' to '2'
FAULTS POSSIBLE -
2nd and 3rd upshift valve sticking.
Governor valve sticking.
'2' Position interlock valve sticking.
SYMPTOM 20 - At speeds below 28 mph when
making a manual selection from '2' to '1',
downshift is delayed or does not occur
FAULTS POSSIBLE -
Governor sticking.
1st to 2nd shift valve sticking.
'1' Position interlock valve sticking.
SYMPTOM 21 - '1' Selected 1st gear no engine
braking
FAULT - Clutch brake 3
SYMPTOM 22 - '2' Selected 2nd gear no engine
braking
FAULT - Clutch brake 1
SYMPTOM 23 - Vehicle drives forward in 'N'
FAULT - Clutch 'A' stuck

ZF
3
REPAIR 19.Disconnect rear propeller shaft to output flange,
and tie to one side.
20.Repeat instructions 18 and 19 on front propeller
shaft to main gearbox.
21.Remove bolts retaining silencer front and rear
securing brackets and tie silencer to one side.
22.Disconnect oil cooler feed and return pipes from
bottom and side of main gearbox.
23.Release cooler pipes from clamp at engine sump
and remove distance piece.
24.Blank pipe ends and unions.
25.Move oil cooler pipes clear of transmission and
tie aside.
26.Disconnect selector cable from operating lever.
27.Disconnect inhibitor switch at multiplug.
28.Attach adaptor plate to hoist.
29.Remove two bolts from transfer gearbox rear
cover.
30.Raise hoist to align adaptor plate with transfer
gearbox and transmission. Secure to transfer
gearbox at rear cover with two bolts removed.
31.Adjust hoist to take weight of transmission.
32.Remove nuts and bolts securing right transfer
gearbox mounting bracket to chassis.
33.Repeat for the left mounting bracket. Removal of
these fixings will also free speedometer
transducer bracket
34.Remove right side mounting bracket to flexible
mounting rubber retaining nut.
35.Lower hoist until rear brake drum clears
passenger footwell. Check engine does not
crush any components while lowering.
36.Remove clip and clevis pin from park brake
lever.
37.Remove clip securing outer brake cable
38.The park brake cable is now free.
39.Disconnect leads from transfer gearbox
temperature sensor and differential lock warning
light switch.
40.Remove ties securing breather pipes to harness.
41.Remove bell housing access plate complete with
gasket.
42.Rotate engine, using crankshaft pulley, until two
access holes are visible in drive plate/ring gear
assembly through bell housing bottom cover
opening.
43.Identify an access hole and bolt hole to aid
reassembly.
44.Remove bolts securing drive plate to convertor
through access holes.
45.Rotate crankshaft half turn to access and
remove remaining bolts.
46.Disconnect oil dipstick tube at main gearbox.
47.Remove bolt at bell housing and detach dipstick
tube. Blank pipe end and union.
48.Position hoist jack channel under engine and
support using a wooden block.
49.Remove bell housing to engine securing bolts,
also detach harness bracket from bell housing.
50.Ease transmission rearwards to allow access to
secure torque converter in bell housing.
51.Lower hoist and complete removal of
transmission.
Refit
52.Ensure torque converter is retained in bell
housing.
53.Secure transmission to adaptor plate on lifting
hoist.
54.Raise hoist and locate transmission with engine.
55.Remove torque converter retainer.
56.Complete attachment of transmission to engine
and fit bell housing bolts. Fit the dipstick tube
bracket and harness bracket to their respective
bolts.
57.Complete refitting by reversing removal
procedure. Note the following important points.
58.Drive plate to torque converter bolts are to be
coated with Loctite 290 prior to assembly.
59.Refill transfer and main gearboxes with correct
grade oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids
60.Check operation of parking brake and adjust as
necessary.
See SECTION 10, Maintenance,
Vehicle Interior

ZF
5
REPAIR Remove
1.Select low range with transfer gear lever.
2.Remove knob and gaiter from transfer gear
lever.
3.Disconnect battery terminals.
4.Remove insulation pad from rocker cover and
inlet manifold.
5.On LH drive vehicles only, disconnect multi-plug
from top of brake fluid reservoir.
6.Release electrical harness from clips along top
of bulkhead and pull over to one side.7.Remove bolt securing transfer and main gearbox
breather pipe clip to rear of cylinder head.
8.Disconnect kick down cable at fuel injection
pump.
9.Drain coolant from cooling system.
10.Disconnect top hose from radiator.
11.Disconnect turbo charger hose from inter-cooler.
12.Remove starter heat shield.