brake LAND ROVER DISCOVERY 1995 Repair Manual

44AUTOMATIC GEARBOX
6
REPAIR 13.Remove starter.
14.Working through starter aperture note position of
torque converter flexible drive plate to facilitate
refitting.
15.Remove the four torque convertor to flexible
drive securing bolts, rotating engine to gain
access to each individual bolt.
16.Raise vehicle on four post ramp [hoist].
17.Drain lubrication oil from transfer and main
gearboxes.
18.Disconnect speedometer cable from transfer
gearbox and disconnect associated clipping.
19.Remove rear propeller shaft.
See PROPELLER
SHAFTS, Overhaul, Flexible Coupling
20.Disconnect front propeller shaft at transfer
gearbox and tie to one side.
21.Remove exhaust front pipe.
22.Remove bolts securing front and centre silencer
mounting brackets and tie silencer to one side.
23.Disconnect oil cooler pipes from gearbox.
24.Blank off pipes and union connections.
25.Remove bolt securing retaining bracket to sump
and move cooler pipes aside.
26.Disconnect selector cable from lever on side of
gearbox.
27.Disconnect inhibitor switch multi-plug.
28.Disconnect park brake cable from linkage to park
brake lever.
29.Disconnect electrical connections from
differential lock switch on transfer gearbox.
30.Remove two lower bolts from transfer gearbox
input bearing support plate.
31.Assemble approved support cradle to
transmission hoist.32.Raise hoist and secure cradle to transfer
gearbox input bearing support plate using bolts
removed.
33.Disconnect gearbox mounting brackets from
chassis cross member.
34.Remove chassis cross member.
35.Lower transmission sufficiently to allow access
to items attached to top of gearbox.
36.Remove left hand gearbox mounting bracket
assembly.
37.Remove ties from breather pipes and harness.
38.Remove nut securing gearbox oil filler/dip stick
tube to bell housing.
39.Release union nut at gearbox sump and remove
filler/dipstick tube. Fit blanking plugs.
40.Support engine using a wooden block with a
suitable ramp [hoist] jack.
41.Remove nut securing kick down cable bracket to
bell housing.
42.Remove two bolts securing top of bell housing to
flywheel housing.
43.Remove nuts securing bell housing to flywheel
housing and withdraw transmission assembly
from engine.
44.Fit a suitable torque converter retaining strap to
the bell housing.
45.Remove hoist and transmission from under
vehicle.
46.Fit lifting eyes to transmission.
47.Using suitable chains and lifting tackle take
weight of transmission assembly.
48.Remove bolts securing transmission cradle to
transfer box and withdraw hoist complete with
cradle.
49.Refit bolts to cover plate.

ZF
7
REPAIR Accessories removal/fitting
If fitting a replacement transmission assembly to the
vehicle, remove the following items from the existing
assembly and fit to the replacement.
CAUTION: It is important to remove the
spacer from the extension shaft and fit
onto the replacement unit.
50.Breather pipe union and washers from main
gearbox.
51.Breather pipe, union and washers from transfer
gearbox.
52.Main gearbox selector lever.
53.RH mounting bracket assembly.
54.Oil cooler pipe unions.
55.Fit blanks to all apertures where unions have
been removed and blank off pipe ends.
Refit
1.Fit transmission to cradle and hoist.
2.Locate hoist under vehicle and remove torque
convertor retaining strap.
3.Ensure low range gear is engaged.
4.Apply approved sealant to bell housing face.
5.Carefully raise assembly, align bell housing with
flywheel housing and bring mating faces
together.
6.Fit nuts and bolts to secure transmission to
engine.
7.Locate electrical wiring and breather pipes to
position.
8.Secure kick down cable clip to bell housing.
9.Raise hoist sufficiently to take weight.
10.Remove block and jack from engine sump.
11.Fit filler/dipstick tube to gearbox sump and
secure bracket to bell housing.
12.Apply Loctite to torque convertor bolts
13.Working through starter aperture refit the four
torque convertor to flexible drive securing bolts,
rotating crankshaft to gain access to bolt
locations.
14.Refit starter and heatshield.
15.Secure breather pipes and harness with ties.
16.Fit left hand mounting bracket assembly to
gearbox.
17.Raise transmission and support with a suitable
ramp [hoist] jack.
18.Remove two bolts securing transmission to
cradle, lower hoist and remove from under
vehicle.
19.Apply Loctite to above bolts and fit to transfer
gearbox input bearing support plate.
20.Fit chassis cross member.21.Secure gearbox mounting brackets to chassis
cross member.
22.Remove ramp [hoist] jack.
23.Connect electrical leads to differential lock
switch.
24.Connect inhibitor switch multi-plug.
25.Connect selector cable to lever on side of
gearbox.
26.Connect oil cooler pipes to gearbox and secure
retaining bracket to gearbox sump.
27.Secure silencer to chassis and refit exhaust front
pipe.
28.Refit front propeller shaft to transfer gearbox.
29.Refit rear propeller shaft.
See PROPELLER
SHAFTS, Overhaul, Flexible Coupling
30.Connect speedometer cable to transfer gearbox.
31.Refill transfer gearbox with correct grade of
lubricating oil.
See LUBRICANTS, FLUIDS
AND CAPACITIES, Information,
Recommended Lubricants and Fluids
32.Lower ramp [hoist] to ground level.
33.Reconnect turbo-charger hose to inter-cooler.
34.Reconnect top hose to radiator.
35.Refill cooling system with correct mixture of
coolant.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids
36.Reconnect kick down cable to fuel injection
pump.
37.Secure breather pipe clip to rear of cylinder
head.
38.Engage harness with clips along top of
bulkhead.
39.On left hand drive vehicles only, connect
multi-plug to top of brake fluid reservoir.
40.Refit insulation pad to rocker cover and inlet
manifold, secure with oil filler cap.
41.Refit gaiter and knob to transfer gear lever.
42.Select high range gear.
43.Reconnect battery terminals.
44.Refill main gearbox with correct grade of
lubricating oil.
See LUBRICANTS, FLUIDS
AND CAPACITIES, Information,
Recommended Lubricants and Fluids

REAR AXLE AND FINAL DRIVE
1
DESCRIPTION AND OPERATION DESCRIPTION
The welded steel rear axle casing houses a separate
spiral bevel type differential unit, which is off set to the
right of the vehicle centre line. The differential unit
drives the rear wheels via the axle shafts and fully
floating hubs which are mounted on tapered roller
bearings.
Lubrication
The differential is lubricated with oil and the hub
bearings with grease. The hub bearings are fittedwith inner and outer seals. The outer seals prevent
the differential oil mixing with the hub grease and the
inner seals prevent dirt ingress into the hub.
Ventilation
Ventilation of the hub bearings is through the outer oil
seals and the differential ventilation pipe, which
terminates at a high level.
The wheel hubs on axles with ABS brakes share the
same construction to non ABS axles except for the
addition of a sensor ring 11 on the brake disc 10.
Rear axle hub
1. Axle casing
2. Ventilation pipe
3. Axle shaft
4. Wheel studs and hub
5. Wheel bearing stub axle
6. Wheel bearings (2)7. Inner hub seal
8. Outer hub/axle shaft seal
9. Hub lock plate, thrust washer and nuts (2)
10. Brake disc
11. Sensor ring, ABS

REAR AXLE AND FINAL DRIVE
1
REPAIR REAR AXLE
Service repair no - 51.25.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
the axle when lowering or repositioning
axle.
1.Drain brake system.
2.Support chassis rear.
3.Remove road wheels.
4.Support axle weight with hydraulic jack.
5.Disconnect ABS wiring harness multi-plug at
jump hose bracket, if applicable.
6.Disconnect shock absorbers.
7.Disconnect flexible brake hose at connection
under floor.
8.Disconnect lower links at axle.
9.Mark differential and propeller shaft flanges with
identification marks for assembly. Remove four
nuts and bolts. Lower propeller shaft and tie to
one side.10.Disconnect pivot bracket ball joint at axle
bracket.
11.Release bolts and remove coil spring retaining
plates.
12.Lower axle and remove road springs.
13.Disconnect anti-roll[sway] bar links to axle.
See
REAR SUSPENSION, Repair, Anti-Roll[Sway]
Bar Ball Joint Links
14.Remove axle assembly.
Refit
15.Position axle and fit lower links. Tighten to
176
Nm
16.Reverse removal procedure.
17.Tighten pivot bracket ball joint to axle to
176 Nm.
18.Tighten propeller shaft to differential drive flange
to
47 Nm
19.Bleed brake system.See BRAKES, Repair,
Brake System Bleed

51REAR AXLE AND FINAL DRIVE
2
REPAIR REAR BRAKE DISC NON ABS
Service repair no - 70.10.11.
Remove
1.Remove rear hub assembly.
See Rear Hub
Assembly
2.Remove disc bolts.
3.Remove disc from rear hub.
Refit
4.Fit disc to rear hub.
5.Fit disc bolts. Tighten to
73 Nm.
6.Check total disc run out, this must not exceed
0,15 mm. If necessary reposition disc.
7.Fit rear hub assembly.See Rear Hub
Assembly
Disc reclamation
8.Check disc thickness. This dimension may be
reduced to minimum thickness of 12 mm.
Machine equal amounts off each face.REAR BRAKE DISCS ABS
Service repair no - 70.11.11.
Remove
1.Remove rear hub assembly.
See Rear Hub
Assembly
2.Remove five nyloc nuts.
3.Remove sensor ring.
4.Remove five hub to disc retaining bolts.
5.Remove disc from hub.
Refit
6.Fit disc onto hub.
7.Apply loctite 270 and fit hub to disc retaining
bolts. Tighten to
73 Nm.
8.Using new nyloc nuts fit sensor ring.
9.Check total disc run out, this must not exceed
0,15 mm. If necessary reposition disc.
10.Fit hub assembly.
See Rear Hub Assembly
Disc reclamation
11.Check disc thickness. This dimension may be
reduced to a minimum thickness of 12 mm.
Machine equal amounts off each face.

REAR AXLE AND FINAL DRIVE
3
REPAIR REAR HUB ASSEMBLY
Service repair no - 64.15.01
Remove
1.Place rear axle onto axle stands and remove
road wheel.
2.Release brake hose clips and remove brake
caliper bolts. Secure to one side.
WARNING: Take care not to kink brake
hose.
3.Remove five bolts and withdraw axle shaft.
4.Remove joint washer.
5.Bend back lock washer tabs.
6.Remove locknut and lock washer.
7.Remove hub adjusting nut.
8.Remove spacing washer.
9.Remove hub and brake disc assembly complete
with bearings.REAR HUB COMPONENTS
1. Sensor ring retaining nut ABS.
2. Axle shaft.
3. Axle shaft joint washer.
4. Axle shaft retaining bolt (five off).
5. Lock nut.
6. Lock washer.
7. Hub adjusting nut.
8. Spacing washer.
9. Outer bearing.
10. Hub.
11. Inner bearing.
12. Grease seal.
13. Brake disc.
14. Disc retaining bolt (five off).
15. Sensor ring ABS.

51REAR AXLE AND FINAL DRIVE
4
REPAIR Refit
10.Clean stub axle. Retract ABS sensor slightly
from sensor sleeve, if applicable
11.Fit hub assembly to stub axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
61 Nm.
Back off adjusting nut 90°. Tighten to4 Nm.
This will give the required hub end float of
0,010mm
14.Fit a new lock washer.
15.Fit locknut. Tighten to61 Nm.
16.Tab over lock washer to secure adjusting nut
and locknut.
17.Using a new joint washer fit axle shaft to hub,
secure with five bolts. Tighten to
65 Nm.
18.Fit brake caliper. Tighten to82 Nm.
Secure brake pipes to axle casing.
19.If applicable, set ABS brakes sensor.
Push sensor in until it touches sensor ring then
rotate hub to set sensor.
20.Fit road wheel, remove axle stands and final
tighten road wheel nuts to
126 Nm.
21.Operate footbrake to locate brake pads before
driving vehicle.

REAR AXLE AND FINAL DRIVE
9
OVERHAUL REAR HUB ASSEMBLY
Service repair no - 61.15.13.
Overhaul
1.Remove rear hub assembly.
See Repair, Rear
Hub Assembly
2.Remove outer bearing.
3.Remove five nyloc nuts and withdraw ABS
sensor ring, if applicable.
4.Mark, for reassembly, position of hub to brake
disc.5.Remove five bolts and separate hub from brake
disc.
WARNING: A maximum of two road wheel
retaining studs can be renewed. Should
more studs be unserviceable fit new hub
with studs.
6.Remove grease seal and inner bearing from
hub.
7.Remove inner and outer bearing tracks.
REAR HUB COMPONENTS
1. Sensor ring retaining nut ABS.
2. Axle shaft.
3. Axle shaft joint washer.
4. Axle shaft retaining bolt (five off).
5. Lock nut.
6. Lock washer.
7. Hub adjusting nut.
8. Spacing washer.9. Outer bearing.
10. Hub.
11. Inner bearing.
12. Grease seal.
13. Brake disc.
14. Disc retaining bolt (five off).
15. Sensor ring ABS.

51REAR AXLE AND FINAL DRIVE
10
OVERHAUL Refit
8.Clean hub and fit inner and outer bearing tracks.
9.Pack hub inner bearing with grease and fit to
hub.
10.With lip side leading fit a new seal flush with rear
face of hub. Using service tool LRT-54-003 seal
replacer and drift. Apply grease between seal
lips.
11.Assemble brake disc to the hub, line up
reassembly marks. Applying Loctite 270, fit and
tighten retaining bolts to
73 Nm.
12.If necessary, where applicable, renew sensor
ring studs applying Loctite 270 to threads. Fit
sensor ring using new nyloc nuts. Tighten to
9
Nm.
Ensuring it is correctly fitted to avoid tooth
run out.
13.Pack hub outer bearing with grease and fit to
hub.
14.Fit rear hub assembly.
See Repair, Rear Hub
Assembly

REAR AXLE AND FINAL DRIVE
1
SPECIFICATIONS, TORQUE AXLE DIFFERENTIAL DATA
Pinion bearing pre-load:
(new bearings) 3 Nm........................................................
(bearings bedded in) 1,5 Nm...............................................
Crown wheel run-out 0,10 mm........................................................
Crown wheel/pinion backlash 0,10 to 0,17 mm...........................................
REAR HUB
Rear hub end float 0,010 mm............................................................
TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
REAR AXLE
Pinion housing to axle case 41.......................................................................
Crown wheel to differential case 58................................................................
Differential bearing cap to pinion housing 90..................................................
Differential drive flange to drive shaft 47.........................................................
Bevel pinion nut 129........................................................................................
Lower link to axle 176......................................................................................
Pivot bracket ball joint to axle 176...................................................................
REAR HUB ABS VEHICLES
Hub driving member to hub 65 *.......................................................................
Brake disc to hub 73 *......................................................................................
Stub axle rear to axle case 65........................................................................
Brake caliper to axle case 82..........................................................................
Disc shield to axle case 11.............................................................................
Sensor ring to brake disc ABS 9....................................................................
* Apply loctite 270 prior to assembly.