fuel LAND ROVER DISCOVERY 1995 Repair Manual

4.0 V8
7
REPAIR 171.Route drive belt around pulleys.
172.Pivot tensioner downwards.
173.Align belt to tensioner and release tensioner.
174.Connect battery positive lead and tighten.
175.Secure terminal cover.
176.Align gearbox breather pipe, clip to engine lifting
eye and fit bolt. Tighten to
9 Nm.
177.Align and secure engine harness brackets to
inlet manifold and fit nuts. Tighten to
9 Nm.
178.Connect injector multiplugs.
179.Connect air intake temperature sensor multiplug.
180.Connect fuel temperature sensor multiplug.
181.Connect coolant temperature multiplug.
182.Connect temperature gauge connector.
183.Connect oil pressure switch Lucar.
184.Connect camshaft sensor multiplug and secure
to bracket.
185.Fit ignition coil bracket.
See FUEL SYSTEM
SFI, Repair, Ignition Coils
186.Position heater hose/pipe assembly.
187.Connect hose to inlet manifold.
188.Align pipe to bracket and fit bolt. Tighten to
9
Nm.
189.Tighten hose clip.
190.Connect heater return hose and tighten clip.
191.Remove plugs from fuel feed and return hose
connections.
192.Clean feed unions.
193.Connect return hose and tighten clip.
194.Connect feed hose union and tighten.
195.Remove cloth.
196.Connect purge hose.
197.Connect leads to generator, tighten terminal nuts
and fit cover.
198.Connect sensing Lucar.
199.Connect servo vacuum hose.
200.Position expansion tank and secure with fixings.
201.Connect hose and tighten clip.
202.Lower ramp.
203.Fit mass air flow sensor.
See FUEL SYSTEM
SFI, Repair, Mass Air Flow Sensor (MAF
Sensor)
204.Fit plenum chamber.See FUEL SYSTEM SFI,
Repair, Plenum Chamber
205.Fit radiator.See COOLING SYSTEM, Repair,
Radiator
206.Fit bonnet.See CHASSIS AND BODY, Repair,
Bonnet [Hood]
207.Reconnect battery negative lead.
208.Bleed power steering system.
See STEERING,
Repair, Power Steering System - Bleed
209.Drain engine oil and refill.See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended Lubricants and Fluids - USA
Vehicles
210.Start engine. Check for fuel, coolant and oil
leaks.FRONT COVER GASKET
Service repair no - 12.65.04 - Front Cover Gasket
Remove
1.Disconnect battery negative lead.
2.Drain cooling system.
See COOLING SYSTEM
V8, Adjustment, Coolant
3.Remove radiatorSee COOLING SYSTEM,
Repair, Radiator
4.Remove water pump pulley.See COOLING
SYSTEM, Repair, Viscous Coupling, Fan
Blades, Pulley and Fan Cowl
5.Slacken bottom hose clip. Remove hose from
water pump.
6.Raise vehicle on ramp.
7.Disconnect oil cooler hoses from front cover and
position aside. Plug hoses and connections.
8.Disconnect Lucar from oil pressure switch.

12ENGINE
8
REPAIR
9.Disconnect multiplug from camshaft sensor.
See FUEL SYSTEM SFI, Repair, Camshaft
Position Sensor (CMP Sensor)
10.Remove 9 bolts securing front cover.
11.Remove 2 bolts securing sump to front cover.
12.Loosen 4 bolts securing sump adjacent to front
cover (2 each side).
13.Release front cover assembly.
14.Remove oil seal.
15.Remove and discard gasket.Refit
16.Clean sealant from threads of cover bolts.
17.Clean old sealant from front cover and block joint
face.
CAUTION: Use a plastic scraper.
18.Apply Hylosil jointing compound to gasket
position on cover and block.
19.Fit new gasket to block face.
20.Ensure oil seal register in cover is clean.
21.Lubricate outer face of NEW oil seal.
22.Using LRT-12-089, fit seal to cover.
23.Lubricate oil pump drive gear and position in
pump with groove away from engine.
24.Locate alignment tool LRT-12-090 on front cover
and oil pump drive gear.
25.Position front cover over crankshaft.
26.Press and rotate tool to engage drive gear until
drive gear keyway aligns with Woodruff key.
27.Fit cover to cylinder block.

12ENGINE
10
REPAIR ROCKER COVER GASKET - LEFT HAND
Service repair no - 12.29.40 - LH Cover Gasket
Service repair no - 12.29.41 - RH Cover Gasket
Remove
1.Disconnect battery negative lead.
2.Remove plenum chamber.
See FUEL SYSTEM
SFI, Repair, Plenum Chamber
3.Remove screw securing dipstick tube to rocker
cover.
4.Release plug leads from guide clips and
disconnect from 4 spark plugs.
5.Remove 4 bolts securing rocker cover to cylinder
head.
6.Remove rocker cover.
7.Remove and discard rocker cover gasket.
Refit
8.Clean mating faces between rocker cover and
cylinder head using Bostick cleaner 6001 or
equivalent. Allow to dry.
NOTE: Gasket fits one way round only. It
must be fitted accurately, first time.
Subsequent movement will destroy
bonding.
9.Apply a thin coating of impact adhesive (Bostick
1775 or equivalent) to mating faces of rocker
cover seal face and new gasket. Use a brush to
ensure an even film. Allow adhesive to become
touch dry.
10.Place one end of gasket into cover recess with
edge firmly against recess wall, holding
remainder of gasket clear. Work around cover,
pressing gasket into place ensuring edge firmly
contacts recess wall.
CAUTION: Allow cover to stand for thirty
minutes before fitting.
11.Fit rocker cover to cylinder head, ensure short
screws are inboard. Tighten to
9 Nm.
12.Connect leads to spark plugs and secure to
guide clips on rocker cover.
13.Secure dipstick tube to rocker cover.
14.Refit plenum chamber.
See FUEL SYSTEM
SFI, Repair, Plenum Chamber
15.Reconnect battery negative lead.

4.0 V8
11
REPAIR ROCKER COVER GASKET - RIGHT HAND
Service repair no - 12.29.41 - RH Cover Gasket
1.Depressurise fuel system.
See FUEL SYSTEM
SFI, Repair, Fuel System - Depressurise
2.Disconnect battery negative lead.3.Drain cooling system.
See COOLING SYSTEM
V8, Adjustment, Coolant
NOTE: Leave hose disconnected.
4.Disconnect purge pipe from plenum chamber
hose.
5.Disconnect breather pipe from rocker cover.
6.Remove bolt securing coolant pipe brackets and
nut securing bracket to manifold.
7.Loosen hose clip and disconnect coolant return
hose from pipe.
CAUTION: Plug connection.
8.Loosen clip and disconnect fuel return hose from
pipe.
9.Disconnect fuel hose from injector pipe.
CAUTION: Use 2 spanners.10.Remove 2 nuts securing engine harness
brackets to manifold.
11.Release 4 ht leads from 2 brackets on rocker
cover.

12ENGINE
12
REPAIR
12.Remove 4 bolts securing rocker cover to cylinder
head.
13.Remove rocker cover.
14.Remove and discard rocker cover gasket.Refit
15.Clean mating faces between rocker cover and
cylinder head using Bostick cleaner 6001 or
equivalent. Allow to dry.
NOTE: Gasket fits one way round only. It
must be fitted accurately, first time.
Subsequent movement will destroy
bonding.
16.Apply a thin coating of impact adhesive (Bostick
1775 or equivalent) to mating faces of rocker
cover seal face and new gasket. Use a brush to
ensure an even film. Allow adhesive to become
touch dry.
17.Place one end of gasket into cover recess with
edge firmly against recess wall, holding
remainder of gasket clear. Work around cover,
pressing gasket into place ensuring edge firmly
contacts recess wall.
CAUTION: Allow cover to stand for thirty
minutes before fitting.
18.Fit rocker cover to cylinder head, ensure short
screws are inboard. Tighten to
9 Nm.
19.Connect fuel feed and return hoses.
20.Refit ht leads into retaining brackets.
21.Secure engine harness to brackets.
22.Connect coolant pipes to hoses and secure
brackets.
23.Connect breather hose to rocker cover.
24.Connect purge hose to plenum chamber.
25.Connect bottom hose to radiator.
26.Refill cooling system.
See COOLING SYSTEM
V8, Adjustment, Coolant
27.Reconnect battery negative lead.

12ENGINE
6
REPAIR ENGINE
Service repair no - 12.41.01
Remove
1.Site vehicle onto ramp [hoist].
2.Remove the drive belt.
See SECTION 10,
Maintenance, Under Bonnet [Hood]
Maintenance
3.Remove radiator.See COOLING SYSTEM,
Repair, Radiator - Mpi
4.Remove bonnet [hood].See CHASSIS AND
BODY, Repair, Bonnet [Hood]
5.Drain engine oil.
6.Position absorbent cloth around fuel pipe to fuel
rail union.
Unscrew union to relieve pressure.
CAUTION: Plug the connections
7.Release clip and disconnect hose from coolant
pump.
8.Release clip and disconnect hose from heater
rail.

12ENGINE
8
REPAIR 21.Release clip and disconnect inlet hose from
power steering pump.
22.Disconnect outlet pipe union at power steering
pump, discard 'O' ring.
CAUTION: Plug the connections
23.Release throttle cable from abutment bracket.
24.Release throttle cable from cam. Also remove
coolant bypass hose from throttle housing.
25.Disconnect stepper motor and throttle
potentiometer multiplugs.
26.Release clip and disconnect hose, air cleaner to
throttle housing.
27.Release clip and disconnect brake servo hose
from manifold.
28.Disconnect fuel temperature sensor multiplug.

Mpi
9
REPAIR 29.Disconnect oil pressure switch multiplug.
30.Disconnect air conditioning compressor
multiplug.
31.Remove 3 bolts securing engine harness to
manifold and fuel pipe.
32.Disconnect knock sensor multiplug.
33.Remove 2 nuts securing harness to starter motor
solenoid, remove harness.
34.Disconnect crankshaft sensor multiplug.
35.Disconnect fuel injection harness multiplug.
36.Disconnect inlet manifold air temperature sensor
multiplug.
37.Release clip and disconnect fuel hose from
pressure regulator.
CAUTION: Plug the connections.

Mpi
13
REPAIR 19.Connect crankshaft sensor, knock sensor, air
conditioning compressor, fuel injector harness,
inlet manifold air temperature and fuel
temperature sensor multiplugs.
20.Connect fuel hose to pressure regulator and
secure with clip.
21.Fit and tighten fuel pipe to fuel rail union.
22.Connect multiplugs to throttle housing.
23.Connect vacuum hose to manifold.
24.Connect oil pressure switch multiplug.
25.Connect brake servo hose to manifold, secure
with clip.
26.Connect throttle cable to cam.
27.Position engine harness and connect breather
hose to inlet manifold, secure with clip.
28.Connect coolant temperature sensor multiplugs,
secure harness with cable tie.
29.Connect oxygen sensor multiplug, secure
harness with cable tie.
30.Connect alternator harness.
31.Connect heater hose to heater rail and secure
with clip.
32.Connect hose to coolant pump and secure with
clip.
33.Connect inlet hose to power steering pump and
secure with clip.
34.Fit and tighten outlet pipe union to power
steering pump.
35.Connect bypass and top hose, secure with clip.
36.Connect air cleaner to throttle housing hose and
secure with clip.
37.Remove engine lifting bracket.
38.Position spark plug cover and secure with
screws.
39.Fill engine with oil.
40.Fit bonnet [hood].
See CHASSIS AND BODY,
Repair, Bonnet [Hood]
41.Fit radiator.See COOLING SYSTEM, Repair,
Radiator - Mpi
42.Adjust throttle cable.See FUEL SYSTEM,
Adjustment, Throttle Cable Adjustment
ENGINE SUMP GASKET
Service repair no - 12.60.43
Remove
1.Drain engine oil.
2.Refit drain plug, use new sealing washer if
necessary, tighten to the correct torque.
3.Remove 18 bolts securing sump.
NOTE: 25mm long bolt is fitted at rear L.H.
corner of sump.
4.Release sump from cylinder block.
5.Discard gasket.

12ENGINE
14
REPAIR Refit
1.Clean sump, remove all traces of gasket from
mating faces of sump and cylinder block.
Visually check sump for damage.
2.Apply beads of RTV sealant to front main
bearing cap.
3.Position new gasket to sump, ensuring that
location pips on gasket are located in sump.
Check gasket lays flat on sump flange.
4.Fit sump. Fit bolts, ensuring that longest bolt is
inserted at position 7.
5.Working around the sump in the sequence
illustrated, tighten the bolts to the stage 1 torque
figure. Then, in the same sequence, tighten the
bolts to the stage 2 torque figure.
NOTE: For torque values.See
Specifications, torque, Torque Values
6.Fill engine with oil.CYLINDER HEAD GASKET
Service repair no - 12.29.01
Remove
1.Disconnect battery negative lead.
2.Position absorbent cloth around fuel pipe to fuel
rail union. Unscrew union to relieve pressure.
CAUTION: Plug the connections.
WARNING: Do not carry out the next
instruction until the coolant is cool to
avoid personal injury from scalding.
3.Release clip and disconnect radiator bottom
hose, allowing coolant to drain into a suitable
container.