differential LAND ROVER DISCOVERY 1995 Workshop Manual

INTRODUCTION
5
INFORMATION JACKING
The following instructions must be carried out before
raising the vehicle off the ground.
1.Use a solid level ground surface.
2.Apply parking brake.
3.Select 'P' or 1st gear in main gearbox.
4.Select Low range in transfer gearbox.
CAUTION: To avoid damage occurring to
the under body components of the vehicle
the following jacking procedures must be
adhered to.
DO NOT POSITION JACKS OR AXLE STANDS
UNDER THE FOLLOWING COMPONENTS.
Body structure
Bumpers
Fuel lines
Brake lines
Front radius arms
Panhard rod
Steering linkage
Rear Trailing links
Fuel tank
Engine sump
Gearbox bell housing
Jack or support vehicle by axles only.Vehicle jack
The jack provided with the vehicle is only intended to
be used in an emergency, for changing a tyre. Do
NOTuse the jack for any other purpose. Refer to
Owner's Manual for vehicle jack location points and
procedure. Never work under a vehicle supported by
the vehicle jack.
Hydraulic jack
A hydraulic jack with a minimum 1500 kg, 3,300 lbs
load capacity must be used.
CAUTION: Do not commence work on the
underside of the vehicle until suitable axle
stands have been positioned under the
axle.
Raise the front of the vehicle
1.Position cup of hydraulic arm under differential
casing.
NOTE: The differential casing is not
central to the axle. Care should be taken
when raising the front road wheels off the
ground as the rear axle has less sway stiffness.

01INTRODUCTION
6
INFORMATION 2.Raise front road wheels to enable an axle stand
to be installed under left hand axle tube.
3.Position an axle stand under right hand axle
tube, carefully lower jack until axle sits securely
on both axle stands, remove trolley jack.
4.Before commencing work on underside of
vehicle re-check security of vehicle on stands.
5.Reverse procedure when removing vehicle from
stands.
Raise rear of vehicle
1.Position cup of hydraulic arm under differential
casing.
2.Raise vehicle to enable axle stands to be
installed under left and right hand axle tubes.
3.Lower jack until axle sits securely on axle
stands, remove trolley jack.
4.Before commencing work on underside of
vehicle re-check security of vehicle on stands.
5.Reverse procedure when removing vehicle from
stands.
HYDRAULIC VEHICLE RAMP (FOUR POST)
Use only a 'drive on' type ramp which supports vehicle
by its own road wheels. If a 'wheel-free' condition is
required, use a 'drive on' ramp incorporating a
'wheel-free' system that supports under axle casings.
Alternatively, place vehicle on a firm, flat floor and
support on axle stands.
TWO POST VEHICLE RAMPS
The manufacturer of LAND ROVER VEHICLES
DOES NOT recommend using 'Two Post' ramps
that employ four adjustable support arms. These
are NOT considered safe for Land Rover vehicles.
If vehicle is installed on a Two Post ramp
responsibility for safety of vehicle and personnel
performing service operations is in the hands of
the Service Provider.DYNAMOMETER TESTING - NON ANTI-LOCK
BRAKE VEHICLES
Viscous coupling
The front and rear axles cannot be driven
independently due to the viscous coupling. This
eliminates the need for differential lock by
progressively locking the centre differential
automatically if slip occurs at any wheel.
WARNING: DO NOT attempt to drive
individual wheels with vehicle supported
on floor jacks or stands.
Four wheel dynamometers
Provided that front and rear dynamometer rollers are
rotating at identical speeds and that normal workshop
safety standards are applied, there is no speed
restriction during testing except any that may apply to
the tyres.
Two wheel dynamometers
IMPORTANT: Use a four wheel dynamometer for
brake testing if possible.
If brake testing on a single axle rig is necessary it
must be carried out with propeller shaft to rear axle
removed, AND neutral selected in BOTH main
gearbox and transfer gearbox. When checking brakes,
run engine at idle speed to maintain servo vacuum.
If checking engine performance, the transfer box must
be in high range and propeller shaft to stationary axle
must be removed.

GENERAL SPECIFICATION DATA
9
INFORMATION TRANSMISSION 3.9 V8i
Manual gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward 1 reverse all synchromesh.............................................................................
Clutch
Make and type Borg and beck diaphram type..................................................................
Clutch plate diameter 266.5mm........................................................
Automatic gearbox
Type ZF4HP Four speed and reverse with fluid torque converter.....................................................................
Transfer box
Type LT230T Two speed reduction on main gearbox output, front....................................................................
and rear drive permanently engaged via a lockable
differential.
Propeller shafts
Type
Front Tubular 51mm diameter.................................................................................
Front - Catalyst vehicles Solid bar 28.6mm diameter...................................................
Rear Tubular 51mm diameter.................................................................................
Universal joints Open type Hookes O3EHD.................................................................
Rear axle
Type Spiral bevel, fully floating shafts.................................................................................
Ratio 3.54:1.................................................................................
Front axle
Type Spiral bevel, enclosed constant velocity joints, fully.................................................................................
floating shafts
Angularity of universal joint on full lock 32° ............................
Ratio 3.54:1.................................................................................

GENERAL SPECIFICATION DATA
15
INFORMATION BULBS
REPLACEMENT BULBS TYPE
Exterior lights
Headlamps 12V 60/55W (Halogen)
Headlamps - France amber 12V 60/55W (Halogen)
Auxiliary driving lamps 12V 55W H3 (Halogen)
Sidelamps 12V 5W bayonet
Tail lamps 12V 5/21W bayonet
Reverse lamps 12V 21W bayonet
Stop lamps 12V 21W bayonet
Direction indicator lamps 12V 21W bayonet
Rear side marker lamps 12V 5W capless
Number plate lamps 12V 5W capless
Interior lights
Instrument panel lamps and warning lamps 12V 1.2W bulb/holder unit
Ignition warning lamp (Instrument panel) 12V 2W capless
Interior roof lamps 12V 10W 'Festoon'
Clock illumination 12V 1.2 capless
Cigar lighter illumination 12V 1.2W capless
Door shut face/puddle lamps 12V 5W capless
Auxiliary switch panel illumination (green) 12V 1.2W capless
Heated rear screen warning lamp (amber) 12V 1.2W capless
Hazard warning lamp 12V 1.2W capless
Automatic graphics illumination 12V 5W capless
Heater/air conditioning graphics illumination 12V 1.2W bulb/holder unit
Differential lock warning lamp 12V 1.2W bulb/holder unit
Column switch illumination 12V 1.2W capless
CAUTION: The fitting of new bulbs with wattages in excess of those specified will result in damage
to vehicle wiring and switches.

GENERAL SPECIFICATION DATA
21
INFORMATION TRANSMISSION - 300 Tdi
Manual gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward 1 reverse all synchromesh.............................................................................
Automatic gearbox
Type ZF4HP Four speed and reverse with fluid torque converter.....................................................................
Transfer box
Type LT230T Two speed reduction on main gearbox output. Front....................................................................
and rear drive permanently engaged via a lockable
differential

04GENERAL SPECIFICATION DATA
24
INFORMATION FUEL SYSTEM - Mpi
Electronic fuel injection data
See ENGINE TUNING DATA, Information, Engine............................................
- Mpi - 2.0 Litre
Fuel Pump:
Make/Type A.C. Rochester/Electric immersible.......................................................................
Pump pressure 3.2 bar.................................................................
Delivery at 3 bar pressure & 12V (min) 64 litre/h............................
Regulated pressure range 3.0 ñ 0.2 bar................................................
Fuel pump delivery pressure 2.3 - 2.5 kgf/cm
2............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
COOLING SYSTEM - Mpi
Pressure cap 15lbf/in
2(1.03 bar) (system pressure) ....................................................................
Thermostat 88 ÊC.......................................................................
CLUTCH - Mpi
Type Diaphragm spring, hydraulically operated.................................................................................
Adjustment Self adjusting.......................................................................
Clutch plate diameter 215.13 mm.......................................................
TRANSMISSION - Mpi
Manual gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward 1 reverse all synchromesh.............................................................................
Transfer box
Type LT230T Two speed reduction on main gearbox output. Front....................................................................
and rear drive permanently engaged via a lockable
differential
Overall ratios (final drive): In high transfer In low transfer
Fifth 4.146:1.................................................................................. 9.761:1
Fourth 4.989:1............................................................................... 11.746:1
Third 7.518:1................................................................................. 17.701:1
Second 11.479:1............................................................................. 27.109:1
First 17.884:1.................................................................................. 42.109:1
Reverse 18.463:1............................................................................ 43.472:1

09LUBRICANTS, FLUIDS AND CAPACITIES
4
INFORMATION CAPACITIES
The following capacity figures are approximate and are provided as a guide only.
Capacities (approx.)* Litres Imp.Unit US unit
Engine sump oil
- 300Tdi models 5,8...................................................... 10.20 pt 12.30 pt
- V8i petrol models 3.9 6,1............................................ 10.70 pt 12.90 pt
- Mpi petrol models 4,90.................................................. 8.70 pt 10.40 pt
Extra when refilling after fitting new filter
- 300Tdi models 0,85...................................................... 1.50 pt 1.80 pt
- V8i petrol models 0,56.................................................. 1.00 pt 1.20 pt
- Mpi 0,4........................................................................ 0.70 pt 0.85 pt
Manual gearbox 2,67............................................................... 4.70 pt 5.70 pt
Automatic gearbox 9,1........................................................... 16.00 pt 19.20 pt
Transfer gearbox oil 2,30......................................................... 4.00 pt 4.90 pt
Front differential 1,70............................................................... 3.00 pt 3.60 pt
Rear differential 1,70................................................................ 3.00 pt 3.60 pt
Power steering box and reservoir LHD 2,90............................ 5.00 pt 6.00 pt
Power steering box and reservoir RHD 3,40............................ 6.00 pt 7.20 pt
Swivel pin housing oil (each) 0,35............................................ 0.60 pt 0.75 pt
Fuel tank usable fuel 89,0........................................................ 19.5 gall 23 gall
Cooling system
- 300Tdi models 11,50...................................................... 20.20 pt 24.30 pt
- V8i petrol models 11,30.................................................. 20.00 pt 23.90 pt
- Mpi 10,00........................................................................ 17.60 pt 21.00 pt
Washer bottle 7,0................................................................... 12.30 pt 14.80 pt
NOTE: * All levels must be checked by dipstick or level plugs as applicable. When draining oil
from the ZF automatic gearbox, oil will remain in the torque converter, refill to high level on
dipstick only.

37MANUAL GEARBOX
2
REPAIR 25.Remove nuts and bolts securing transmission
cross-member to chassis.
26.Remove nuts and bolts securing cross-member
mountings to transmission.
27.Remove cross-member.
28.Manufacture an adapter plate to dimensions
given in service tool section and attach it to a
transmission hoist. To achieve balance of the
transmission unit when mounted to hoist, it is
essential that pointA,is situated over lifting hoist
ram. Drill holesBto suit hoist table. Secure the
transmission unit cradle at pointCusing the
lower bolts retaining transfer gearbox rear cover.
Raise hoist just enough to take weight of
transmission.
29.Lower hoist sufficiently to allow transfer gearbox
selector lever to clear transmission tunnel
aperture.
30.Disconnect differential lock switch connectors.
31.Disconnect reverse lamp switch connectors.
32.Remove clips securing gearbox breather pipes
to harness.
33.Support engine under sump with a jack.
CAUTION: Use a wooden block to protect
sump.
34.Remove bell housing nuts.
35.Withdraw transmission whilst ensuring all
connections to engine and chassis are released.36.Remove transmission assembly from hoist
cradle and position safely on a bench.
37.Remove breather pipes. Discard pipe union
sealing washers.
38.Remove 'Nyloc' nut, and remove bolt, securing
lever to high/low shaft.
39.Collect spacer washer.
40.Remove 2 clips and remove differential lock
lever link.
41.Remove lower locknut from high/low operating
rod.
42.Place a sling round transfer box and attach to
hoist.
43.Remove nut and 5 bolts securing transfer
gearbox to extension housing.
44.Withdraw transfer gearbox.

R380
3
REPAIR Assembling transfer gearbox to main gearbox
45.Clean extension housing and transfer gearbox
mating faces.
46.Ensuring loose upper dowel is fitted, hoist
transfer gearbox into position.
47.Fit and tighten nut and bolts to
34Nm.
48.Connect high/low operating rod, fit and tighten
locknut.
49.Fit link to differential lock lever and secure with 2
clips
50.Align lever to high/low shaft, position washer, fit
bolt and new Nyloc nut. Tighten to
2Nm.
51.Position breather pipes, secure pipe unions
using new sealing washers. Tighten unions to
15Nm.
Fitting transfer gearbox and main gearbox
assembly to engine
52.Position transmission assembly to hoist cradle.
53.Clean bell housing and engine mating faces.
54.Temporarily fit gear lever and select any gear in
main gearbox to facilitate entry of gearbox input
shaft.
55.Position and raise hoist, and fit transmission to
engine whilst keeping wires and pipes clear to
prevent trapping.
56.Fit and tighten nuts securing transmission to
engine.
57.Connect reverse lamp switch connectors and
differential lock switch connectors.
58.Secure breather pipes to harness with clips.
59.Position temporary support.
60.Remove 2 bolts securing lifting cradle to
transmission and remove hoist. Apply Loctite
290 to bolts and refit bolts.
61.Position cross-member, loosely fit nuts and bolts
securing cross-member mountings to
transmission.62.Raise transmission, align cross-member and
loosely fit nuts and bolts securing cross-member
to chassis.
63.Tighten all securing nuts and bolts. Remove
supporting jack from under sump.
64.Remove temporary support.
65.Fit handbrake cable through transmission tunnel
and secure gaiter.
66.Connect speedometer cable to transfer gearbox.
67.Line up marks and connect front and rear
propeller shafts.
68.Clean spacer, clutch slave cylinder and gearbox
mating faces.
69.Position spacer and slave cylinder, fit bolts.
Tighten to
25Nm.
70.Untie intermediate exhaust pipe(s) and refit
exhaust front pipe(s).
See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust System
Complete
71.Refill main gearbox and transfer gearbox with oil.
See SECTION 10, Maintenance, Under
Vehicle Maintenance
72.Lower ramp [hoist].
73.Fit fan cowl, fit and tighten bolts.
74.Align breather pipe clip to cylinder block, fit and
tighten bolts.
75.Fit handbrake cable adjuster and secure with 'C'
clip.
76.Align cable trunnion to handbrake lever, fit clevis
pin and secure with clip.
77.Check handbrake adjustment.
See SECTION
10, Maintenance, Vehicle Interior
78.Fit upper gear lever, fit and tighten bolt.
79.Fit gear selector lever and high/low selector
lever draft excluders.
80.Position draft excluder clamp rings, fit and
tighten screws.
81.Refit sound insulation.
82.Refit centre console.
See CHASSIS AND
BODY, Repair, Centre Console
83.Connect battery earth lead.

TRANSFER GEARBOX
1
DESCRIPTION AND OPERATION LT230T TRANSFER BOX
The LT230T transfer box is a permanent 4 wheel
drive, two speed ratio reducing gearbox incorporating
high and low range outputs with mechanically lockable
centre differential (diff-lock). High/low range and
diff-lock selection are made via a single lever located
forward of the main gear lever.
A shiftlock device is fitted in some territories, it is used
as a park facility and prevents accidental gear
disengagement when the ignition is switched off. An
audible neutral alarm is also fitted. This alerts the
driver when parking to move the gear lever to the high
or low position.