fuel LAND ROVER FREELANDER 2001 Workshop Manual

HEATING AND VENTILATION
REPAIRS 80-19
11.Release clip securing air intake hose to FBH,
release clamp from exhaust manifold.
12.Remove 2 bolts securing air intake and exhaust
assembly to FBH and move aside.
Refit
1.Fit exhaust pipe, air intake hose and bracket
assembly to FBH.
2.Fit and tighten bolts to 10 Nm (7.5 lbf.ft).
3.Tighten exhaust pipe clamp to 5 Nm (3.5 lbf.ft).
4.Align air intake hose with mark on casing and
secure with clip.
5.Fit mounting bracket to FBH and tighten bolts to
10 Nm (7.5 lbf.ft).
6.Connect multiplugs to FBH.
7.Fit FBH to body, tighten bolts to 10 Nm (7.5
lbf.ft).
8.Fit coolant hoses to FBH and secure with clips.
9.Fit fuel feed hose to FBH and secure with clip.
10.Refill cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.
11.Fit front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
12.Connect battery earth lead.
Sensor - outside temperature (OT)
$% 80.40.31
Remove
1.Remove front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
2.Disconnect multiplug from OT sensor.
3.Remove OT sensor from mounting bracket,
collect rubber washer and spacer.
Refit
1.Clean OT mounting bracket and sensor.
2.Fit OT sensor to mounting bracket, fit rubber
washer and spacer, connect multiplug.
3.Fit front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.

HEATING AND VENTILATION
80-20REPAIRS
Fuel pump - fuel burning heater - up to
03MY
$% 80.40.40
Remove
1.Disconnect battery earth lead.
2.Remove RH rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
3.Disconnect multiplug from fuel pump.
4.Release clips and remove fuel pipes from fuel
pump.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
5.Release fuel pump from rubber mountings and
remove pump.Refit
1.Clean fuel hose connections.
2.Position fuel pump and secure in rubber
mountings.
3.Position fuel pipes to pump and secure with
clips.
4.Connect multiplug to fuel pump.
5.Fit rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
6.Connect battery earth lead.
M80 0495

HEATING AND VENTILATION
REPAIRS 80-21
Fuel pump - fuel burning heater - from
03MY
$% 80.40.40
Remove
1.Disconnect battery earth lead.
WARNING: Fuel vapour is highly flammable
and in confined spaces is also explosive
and toxic. Always have a fire extinguisher
containing foam, CO
2, gas or powder close
at hand when handling or draining fuel.
2.Raise vehicle on lift.
3.Remove 2 bolts securing fuel pump and filter
assembly to body.
4.Lower fuel pump and filter assembly.
5.Disconnect multiplug from fuel burning heater
pump.
6.Position container below fuel pipes to collect
fuel spillage.7.Disconnect fuel pipes from fuel burning heater
pump.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
8.Release and remove fuel burning heater pump
from fuel pump and filter assembly.
Refit
1.Clean fuel pipe connections.
2.Fit and secure fuel burning heater pump to fuel
pump and filter assembly.
3.Connect fuel pipes to fuel burning heater pump.
4.Remove container from below fuel pipes.
5.Connect multiplug to fuel burning heater pump.
6.Position fuel pump and filter assembly to body,
fit bolts and tighten to 10 Nm (7 lbf.ft).
7.Lower vehicle on lift.
8.Connect battery earth lead.
M19 3624

AIR CONDITIONING
82-10REPAIRS
Condenser
$% 82.15.07
Remove
1.Disconnect battery earth lead.
2.Recover refrigerant from A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
3. Td4 models: Remove intercooler.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Intercooler.
4. Remove bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
5. KV6 models: Remove 2 bolts securing PAS
fluid cooler to armature.
6. Up to 04MY: Remove 4 nuts and 4 bolts
securing armature to body, remove armature.
7. 04MY on: Remove 4 bolts securing armature to
crash cans and remove armature.8.If fitted, remove 4 scrivets securing LH and RH
air deflectors, remove both deflectors.
9.Remove 2 bolts securing condenser to radiator.
10.Remove 2 bolts securing receiver drier
mounting brackets to radiator.

M76 4176

AIR CONDITIONING
REPAIRS 82-11
11.Remove 2 bolts securing A/C pipes to
condenser and release pipes from condenser.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
12.Remove and discard 'O' rings from A/C pipes.
13.Remove condenser.
14.Remove 8 screws, securing 4 mounting
brackets to condenser and move aside.
15.Remove and discard receiver drier, plug
connections.Refit
1.Fit condenser mounting brackets, fully tighten
LH screws. Leave RH screws loose until
receiver drier is fitted.
CAUTION: Ensure that bolts of the correct
length are used on refit.
2.Lubricate new 'O' rings with clean refrigerant
oil, fit one seal to each condenser pipe.
3.Position A/C pipes to condenser, fit bolts and
tighten to 8 Nm (6 lbf.ft).
4.Fit bolts securing condenser to radiator and
tighten to 8 Nm (6 lbf.ft).
5.Fit receiver drier assembly to condenser.

+ AIR CONDITIONING, REPAIRS,
Receiver drier.
6.Fit air deflectors and secure with scrivets.
7. Up to 04MY: Position armature, fit and tighten
4 nuts and bolts securing armature to body to
25 Nm (18 lbf.ft).
8. 04MY on: Position armature, fit bolts securing
armature to crash cans and tighten to 25 Nm
(18 lbf.ft).
9. KV6 models:Align PAS fluid cooler and tighten
bolts to 8 Nm (6 lbf.ft).
10.Fit bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
11. Td4 models: Fit intercooler.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Intercooler.
12.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
13.Connect battery earth lead.
M82 0706

AIR CONDITIONING
82-12REPAIRS
Receiver drier
$% 82.17.03
Remove
1.Disconnect battery earth lead.
2.Recover refrigerant from A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
3. Remove bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
4. KV6 models: Remove 2 bolts securing PAS
fluid cooler to armature.
5. Up to 04MY: Remove 4 nuts and 4 bolts
securing armature to body and remove
armature.
6. 04MY on: Remove 4 bolts securing armature to
crash cans and remove armature.
7.If fitted, remove 2 scrivets securing LH air
deflector and remove air deflector.8. Td4 models: Remove intercooler.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Intercooler.
9.Remove 4 screws from clamps securing
receiver drier to condenser.
10.Remove receiver drier from condenser.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
11.Discard dust shield and 'O' ring seals.

M76 4176

AIR CONDITIONING
REPAIRS 82-13
Refit
1.Lubricate new 'O' rings, dust shield and
condenser thread with refrigerant oil.
2.Fit 'O' rings and dust shield to receiver drier.
CAUTION: Do not remove receiver/dryer
from packaging until immediately before
installation.
3.Fit receiver drier to condenser and tighten to 12
Nm (9 lbf.ft).
4.Tighten clamps securing receiver drier to
condenser.
5.If fitted, fit air deflector and secure with scrivets.
6. Td4 models: Fit intercooler.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Intercooler.
7. Up to 04MY: Position armature, fit and tighten
4 nuts and bolts securing armature to body to
25 Nm (18 lbf.ft).
8. 04MY on: Position armature, fit bolts securing
armature to crash cans and tighten bolts to 25
Nm (18 lbf.ft).
9. KV6 models: Align PAS fluid cooler and
tighten bolts to 8 Nm (6 lbf.ft).
10.Fit bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
11.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
12.Connect battery earth lead.
Switch - control
$% 82.20.07
Remove
1.Remove radio.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio - up to 04MY.
2.Remove 3 heater control knobs.
3.Remove 2 screws securing heater control
finisher to heater controls and remove finisher.
4.Disconnect multiplug from A/C control switch.
5.Remove switch from heater controls.
Refit
1.Fit A/C control switch and connect multiplug.
2.Fit heater control finisher and secure with
screws.
3.Fit heater control knobs.
4.Fit radio.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio - up to 04MY.

CHARGING AND STARTING
REPAIRS 86-1-17
Starter motor - K1.8
$% 86.60.01
Remove
1.Disconnect battery earth lead.
2.Remove air cleaner assembly.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Air cleaner - K1.8.
3.Disconnect Lucar connector from starter motor.
4.Remove nut and disconnect battery lead from
starter solenoid.
5.Remove lower nut and bolt securing starter
motor.
6.Remove bolt securing steady bar to engine LH
mounting.
7.Remove upper nut and bolt securing starter
motor.
8.Remove engine steady bar.
9.Remove starter motor.Refit
1.Clean starter motor and mating face.
2.Ensure gearbox closing plate is in position.
3.Fit starter motor and fit lower bolt but do not
tighten bolt at this stage.
4.Fit engine steady bar, fit bolt securing steady
bar to engine mounting but do not tighten at this
stage.
5.Fit starter motor upper bolt.
6.Tighten starter motor upper and lower nuts and
bolts to 80 Nm (59 lbf.ft).
7.Tighten bolt securing engine steady bar to LH
engine mounting to 25 Nm (18 lbf.ft).
8.Connect battery cable to starter solenoid, fit nut
and tighten to 8 Nm (6 lbf.ft).
9.Connect Lucar to solenoid.
10.Fit air cleaner assembly.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Air cleaner - K1.8.
11.Connect battery earth lead.

HARNESSES
86-7-8 REPAIRS
74.Release all harness clips from interior of
vehicle.
75.Release and disconnect multiplugs from base
of 'B/C' posts.
76.Remove luggage compartment carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.77.Remove 6 screws from fuel pump access cover
and remove cover.
78.Disconnect multiplug from fuel pump.
79.Release both rear ABS speed sensor
harnesses and disconnect multiplugs.
80.Pull harness into vehicle interior.

HARNESSES
86-7-10 REPAIRS
90.Remove 4 screws from rear bumper lamps,
release lamps and disconnect multiplugs.
91.Release harness clips and pull harness into
luggage compartment.
92.Release main harness retaining clips and pull
harness into vehicle interior.
93.Remove main harness.Refit
1.Lay main harness in vehicle.
2.Locate rear section and secure in retaining
clips.
3.Feed harness to rear bumper lamps, secure in
clips and grommets.
4.Connect multiplugs to rear bumper lamps, fit
rear lamps and secure with screws.
5.Fit LH rear earth header and secure with nut.
6.Connect multiplugs to LH tail lamp.
7.Position RH tail lamp and connect multiplugs.
8.Fit RH tail lamp and secure with Torx screws.
9.Fit RH rear earth header and secure with nut.
10.Connect multiplug to towing electrics.
11.Connect rear screen washer tube.
12.Connect tail door harness multiplugs.
13.Connect and fit rear window lift and wash/wipe
relays.
14.Position harness into luggage compartment.
15.Connect both rear ABS speed sensor
multiplugs and secure harness grommets.
16.Connect multiplug to fuel pump.
17.Fit fuel pump access cover and secure with
screws.
18.Fit luggage compartment carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
19.Connect multiplugs at the base of 'B/C' Posts.
20.Fit all harness clips to interior of vehicle.
21.Fit multiplugs and earth header to LH lower 'A'
post.
22.Fit earth header to RH lower 'A' post.
23.Connect multiplug to window lift ECU.
24.Fit face level vent ducting.
25.Fit steering column to bracket and secure with
nuts.
26.Fit rear heater ducting and secure with nut.
27.Secure harness to rear heater ducting with
clips.
28.Position mounting bracket and secure relays.
29.Connect Lucar to handbrake switch.
30. Manual gearbox only: Connect multiplug to
gear lever hill descent switch.
31.Connect multiplug to accelerometer.
32. Automatic gearbox only: Connect multiplugs
to gear selector.
33.Connect heated oxygen sensor multiplug.
34.Fit earth header to floor tunnel and secure with
nut.
35.Fit earth lead to airbag ECU and secure with
bolt.
36.Connect multiplug to airbag ECU.
37.Connect multiplugs to brake light switch and
brake pedal position switch.
38.Connect multiplug to throttle position sensor.
39.Fit harness clip to steering column.
40.Connect multiplug to steering column switch.