Starter motor LAND ROVER FREELANDER 2001 User Guide

AUTOMATIC GEARBOX - JATCO
REPAIRS 44-27
21.Fit new circlip to LH drive shaft.
22.With assistance, fit LH drive shaft to gearbox,
keep shaft square to prevent damage to oil seal
in gearbox.
23.Fit IRD.

+ INTERMEDIATE REDUCTION
DRIVE, REPAIRS, Intermediate reduction
drive (IRD) unit - Td4.
24.Fit starter motor.

+ CHARGING AND STARTING,
REPAIRS, Starter motor - Td4.
25.Fit fluid cooler.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Fluid cooler - Td4.
26.Fit intake ducting assembly.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Ducting - intake assembly.
27.Connect battery earth lead.
28.Untie and close bonnet.
Fluid pan - reseal
$% 44.24.05
Remove
1.Drain gearbox fluid.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
2.Remove fluid cooler.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Fluid cooler - KV6.
3.Release multiplugs from clips attached to fluid
pan.
4.Remove 21 bolts securing fluid pan to gearbox.
5.Remove fluid pan.
Refit
1.Clean fluid pan and mating face on gearbox.
2.Apply sealant, Part No. STC 4600to contact
faces of fluid pan and gearbox.
3.Position fluid pan, fit bolts and tighten
progressively to 7 Nm (5 lbf.ft).
4.Secure multiplugs to clips.
5.Fit fluid cooler.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Fluid cooler - KV6.
6.Fill gearbox with fluid.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.

CHARGING AND STARTING
REPAIRS 86-1-15
Starter motor - Td4
$% 86.60.01
Remove
1.Disconnect battery earth lead.
2. Models with automatic transmission:
Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
3.Remove engine acoustic cover if fitted.

+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
4.Release terminal cover, remove nut and
disconnect 2 cables from starter motor
solenoid.
5.Remove 2 bolts and remove starter motor.Refit
1.Clean starter motor and mating face. Clean
dowel and dowel hole.
2.Fit starter motor and tighten bolts to 45 Nm (33
lbf.ft)
3.Fit cables to starter motor solenoid and tighten
nut to 13 Nm (9.5 lbf.ft). Secure terminal cover.
4.Connect Lucar to starter motor solenoid.
5.Fit engine acoustic cover if fitted.

+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
6. Models with automatic transmission: Fit
battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
7.Connect battery earth lead.
M86 5383

CHARGING AND STARTING
86-1-16 REPAIRS
Starter motor - KV6
$% 86.60.01
Remove
1.Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
2.Release starter motor solenoid terminal cover,
remove nut securing battery lead to solenoid
and disconnect battery lead.
3.Disconnect Lucar connector from starter
solenoid.
4.Remove 3 bolts securing starter motor to
gearbox noting that the LH bolt also secures
the mounting bracket for the CKP sensor
multiplug.
5.Manoeuvre and remove starter motor.Refit
1.Clean starter motor and mating face on
gearbox.
2.Position starter motor to gearbox, align CKP
sensor multiplug bracket, fit and tighten bolts to
45 Nm (33 lbf.ft).
3.Connect battery lead to solenoid terminal, fit
nut and tighten to 13 Nm (9.5 lbf.ft). Secure
terminal cover.
4.Connect Lucar connector to starter solenoid.
5.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.

CHARGING AND STARTING
REPAIRS 86-1-17
Starter motor - K1.8
$% 86.60.01
Remove
1.Disconnect battery earth lead.
2.Remove air cleaner assembly.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Air cleaner - K1.8.
3.Disconnect Lucar connector from starter motor.
4.Remove nut and disconnect battery lead from
starter solenoid.
5.Remove lower nut and bolt securing starter
motor.
6.Remove bolt securing steady bar to engine LH
mounting.
7.Remove upper nut and bolt securing starter
motor.
8.Remove engine steady bar.
9.Remove starter motor.Refit
1.Clean starter motor and mating face.
2.Ensure gearbox closing plate is in position.
3.Fit starter motor and fit lower bolt but do not
tighten bolt at this stage.
4.Fit engine steady bar, fit bolt securing steady
bar to engine mounting but do not tighten at this
stage.
5.Fit starter motor upper bolt.
6.Tighten starter motor upper and lower nuts and
bolts to 80 Nm (59 lbf.ft).
7.Tighten bolt securing engine steady bar to LH
engine mounting to 25 Nm (18 lbf.ft).
8.Connect battery cable to starter solenoid, fit nut
and tighten to 8 Nm (6 lbf.ft).
9.Connect Lucar to solenoid.
10.Fit air cleaner assembly.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Air cleaner - K1.8.
11.Connect battery earth lead.

HARNESSES
REPAIRS 86-7-3
18.With assistance feed harness through bulk
head into vehicle.
19.Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
20.Remove 3 cable ties and release bonnet
release cable from harness.
21.Disconnect multiplug from cooling fan pack and
2 multiplugs from cooling fans.
22.Release 4 clips securing harness to cooling
fans and release harness from cooling fans.
23.Disconnect 2 multiplugs from LH headlamp and
headlamp levelling motor.
24.Disconnect multiplug from harness.25.Remove nut securing LH earth header and
release header.
26.Disconnect multiplug from front LH ABS speed
sensor.
27.Disconnect Lucar connector from starter motor.
28. Models with cruise control:Disconnect
multiplug from cruise control vacuum pump.
29.Release 5 harness retaining clips.
30.Disconnect 2 engine harness to main harness
multiplugs.
31.Release 5 Allen screws securing 'E' box cover
to 'E' box.
32.Remove 'E' box cover

HARNESSES
REPAIRS 86-7-11
41.Position fuse box to body and connect
multiplugs.
42.Fit relays to fuse box bracket.
43.Connect coaxial cable.
44.Fit and connect multiplug to RH 'A' post.
45.Fit passenger compartment fuse box and
secure with bolts.
46.Position side repeater lamps, connect
multiplugs and fit to wings.
47.Secure rear edge of front wheel arch liners.
48.Fit front mud flaps and secure with screws.
49.With assistance feed harness through bulk
head into engine bay.
50.Position harness to wiper motor and connect
multiplug.
51.Fit air intake plenum.

+ HEATING AND VENTILATION,
REPAIRS, Plenum - air intake.
52.Secure harness to LH side of engine bay and
secure fixings.
53.Connect multiplug to inertia switch.
54.Connect multiplugs to underside of fuse box.
55.Fit nuts securing fuse box to brackets.
56.Fit battery connections and multiplug to fuse
box.
57.Fit fuse box cover.
58.Connect 'E' box cooling fan multiplug.
59.Connect 'E' box temperature sensor multiplug.
60.Connect engine harness multiplugs to main
harness.
61. Automatic gearbox only:Connect multiplug to
gearbox ECU.
62.Fit 'E' box cover and secure with Allen screws.
63.Connect engine harness multiplugs to main
harness.
64.Fit harness retaining clips.
65. Models with cruise control: Connect
multiplug to vacuum pump.
66.Connect Lucar connector to starter motor.
67.Connect multiplug to LH ABS speed sensor.
68.Fit LH earth header and secure with nut.
69.Connect multiplug to harness.
70.Connect multiplugs to LH headlamp and
headlamp levelling motor.
71.Secure harness to cooling fan clips.
72.Connect multiplugs to cooling fan pack and
cooling fans.
73.Position bonnet release cable to harness and
secure with cable ties.
74.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
75.With assistance feed harness through bulk
head into engine bay.
76.Fit earth header to bulk head and secure with
nut.
77.Fit front screen washer tube to harness.
78.Fit harness retaining clips.79.Fit PAS and coolant reservoir support bracket
and secure with bolt and nuts.
80.Connect multiplug to bonnet switch.
81.Connect multiplug to brake fluid low level
indicator switch.
82.Fit jack to holder in engine bay.
83.Connect multiplugs to horn, refrigerant
pressure sensor and compressor.
84.Connect multiplugs to RH headlamp and
headlamp levelling motor.
85.Connect multiplug to RH ABS speed sensor
and secure to clips.
86.Connect multiplug to ABS modulator.
87.Fit earth header to RH inner wing and secure
with nut.
88.Position harness to windscreen washer
reservoir.
89.Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
90.Fit engine acoustic cover.

+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
91.Fit carpet.