coil LAND ROVER FREELANDER 2001 User Guide

TORQUE WRENCH SETTINGS
06-7
† Tighten in sequence
*New bolts must be fitted
+ Apply sealant, Part No. STC50552 to threads
++ Apply sealant, Part No. STC 4600 to threads
+++ Apply sealant, Part No. STC 50550 to threads
Ignition coils to LH inlet manifold nut and bolts 9 Nm 7 lbf.ft
Ignition plug top coils to spark plug bolts 9 Nm 7 lbf.ft
Inlet manifold to cylinder head nuts and bolts 25 Nm 18 lbf.ft
IRD support bracket to front mounting plate bolts 45 Nm 33 lbf.ft
IRD support bracket to sump bolts 45 Nm 33 lbf.ft
LH mounting to body bolts 48 Nm 35 lbf.ft
LH mounting bracket to gearbox bolts 85 Nm 63 lbf.ft
LH mounting to gearbox bracket through bolt 100 Nm 74 lbf.ft
Oil cooler to sump mounting bracket nuts 25 Nm 18 lbf.ft
Oil cooler pipes to oil filter and oil cooler unions 26 Nm 19 lbf.ft
Oil dipstick tube bracket to cylinder block bolt 9 Nm 7 lbf.ft
Oil pick-up strainer to bearing ladder bolts
+8 Nm 6 lbf.ft
Oil pressure relief valve plug nut
+25 Nm 18 lbf.ft
Oil pressure switch 14 Nm 10 lbf.ft
Oil pump to cylinder block bolts
†
⇒ Stage 1
⇒ Stage 25 Nm
9 Nm4 lbf.ft
7 lbf.ft
PAS pipe to engine front mounting plate bolt 25 Nm 18 lbf.ft
PAS pipe support bracket to RH hydramount nut 85 Nm 63 lbf.ft
Sump to lower crankcase bolts
†++35 Nm 26 lbf.ft
Timing belt cover (front LH and RH) bolts 4 Nm 3 lbf.ft
Timing belt cover (lower) to cylinder block bolts 9 Nm 7 lbf.ft
Timing belt cover (rear LH and RH) bolts 4 Nm 3 lbf.ft
Rear timing belt cover backplate bolts 9 Nm 7.5 lbf.ft
Top arm to RH hydramount nut 85 Nm 63 lbf.ft
Top arm bracket to engine front plate and RH mounting bolts 100 Nm 74 lbf.ft

TORQUE WRENCH SETTINGS
06-10
Engine Management System – MEMS
+ Apply sealant, Part No. STC 50552 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
Camshaft position (CMP) sensor bolt 8 Nm 6 lbf.ft
Crankshaft position sensor (CKP) to housing bolt 8 Nm 6 lbf.ft
'E' box retaining clip nut 9 Nm 7 lbf.ft
Engine coolant temperature (ECT) sensor to housing bolt
*15 Nm 11 lbf.ft
Fuel cut-off (inertia) switch nuts 2 Nm 1.5 lbf.ft
Idle air control (IAC) valve to manifold Torx screws 1.5 Nm 1.1 lbf.ft
Ignition coil and ht lead cover bolts 10 Nm 7.5 lbf.ft
Ignition coil mounting bolts 8 Nm 6 lbf.ft
Spark plugs to cylinder head 27 Nm 20 lbf.ft
Throttle body to inlet manifold chamber Torx screws (KV6) 7 Nm 5 lbf.ft
Throttle actuator support bracket to throttle body Torx screws
(vehicles with cruise control only)9 Nm 7 lbf.ft
Throttle position sensor to housing Torx screws 1.5 Nm 1.1 lbf.ft

TORQUE WRENCH SETTINGS
06-11
Engine Management System – Siemens
TORQUE DESCRIPTION METRIC IMPERIAL
Camshaft position (CMP) sensor 8 Nm 6 lbf.ft
CMP sensor mounting bracket bolt 8 Nm 6 lbf.ft
Crankshaft position (CKP) sensor bolt 9 Nm 6.5 lbf.ft
Engine Coolant temperature (ECT) sensor 17 Nm 12.5 lbf.ft
'E' box cover Allen screws 2 Nm 1.5 lbf.ft
'E' box mounting nut 9 Nm 7 lbf.ft
Plug top coils to LH inlet manifold nut and bolt 9 Nm 6.5 lbf.ft
Plug top coils to RH camshaft cover bolts 9 Nm 6.5 lbf.ft
Spark plugs25 Nm 18 lbf.ft
Throttle body to inlet manifold chamber Torx screws (KV6) 7 Nm 5 lbf.ft
Throttle pedal assembly to bulkhead nuts 25 Nm 18 lbf.ft
Throttle position (TP) sensor screws 1.5 Nm 1.1 lbf.ft

TORQUE WRENCH SETTINGS
06-13
Fuel delivery system – Petrol
1 Tighten in sequence using the procedure defined in 'Repairs' section.

+ ENGINE MANAGEMENT SYSTEM - SIEMENS, REPAIRS, Sensor - combined - manifold absolute
pressure/Intake air temperature (MAP/IAT).
TORQUE DESCRIPTION METRIC IMPERIAL
Air cleaner to battery tray bolts 9 Nm 7 lbf.ft
Fuel filler neck to body nuts and bolt 9 Nm 7 lbf.ft
Fuel pump/sender unit to tank locking ring 35 Nm 26 lbf.ft
Fuel rail to inlet manifold bolt 8 Nm 6 lbf.ft
Fuel tank to body bolts 40 Nm 29 lbf.ft
Heated Oxygen (HO
2S) Sensor 40 Nm 29 lbf.ft
Ignition coils to LH inlet manifold nuts and bolts - KV6 - Up to 03 Model Year 9 Nm 7 lbf.ft
Inertia (fuel cut-off) switch 2 Nm 1.5 lbf.ft
Intake Air Control Valve (IACV) to throttle body Allen screws 6 Nm 4.5 lbf.ft
Subframe to body bolts 190 Nm 140 lbf.ft
Throttle housing to inlet manifold bolts
1 (K1.8)
⇒1st. stage4 Nm 3 lbf.ft
⇒2nd. stage9 Nm 7 lbf.ft
Throttle body to inlet manifold chamber Torx screws (KV6) 8 Nm 6 lbf.ft
Throttle actuator support bracket to throttle body Torx screws (vehicles with cruise
control only)9 Nm 7 lbf.ft
Throttle position sensor to housing Torx screws 1.5 Nm 1.1 lbf.ft
VIS motor to inlet manifold chamber screws (KV6 only) 8 Nm 6 lbf.ft

TORQUE WRENCH SETTINGS
06-16
Manifolds and Exhaust Systems – K1.8
†Tighten in sequence.
TORQUE DESCRIPTION METRIC IMPERIAL
Alternator bolts45 Nm 33 lbf.ft
Alternator mounting bracket bolts 25 Nm 18 lbf.ft
Coil cover bolts10 Nm 7.5 lbf.ft
Exhaust heatshield to manifold bolts 10 Nm 7.5 lbf.ft
Exhaust heatshield to manifold nut 25 Nm 18 lbf.ft
Exhaust front pipe to intermediate pipe nuts 60 Nm 44 lbf.ft
Exhaust front pipe to manifold nuts 60 Nm 44 lbf.ft
Exhaust manifold to cylinder head nuts
†45 Nm 33 lbf.ft
Exhaust manifold heatshield to front pipe bolts 9 Nm 7 lbf.ft
Heated Oxygen (HO
2S) Sensor 55 Nm 41 lbf.ft
Heatshield to alternator bracket:
⇒ Nut25 Nm 18 lbf.ft
⇒ Bolts10 Nm 7.5 lbf.ft
Inlet manifold to cylinder head nuts
†17 Nm 12.5 lbf.ft
Intermediate pipe to tail pipe flange nuts 60 Nm 44 lbf.ft
RH coil bolts10 Nm 7.5 lbf.ft
Tail pipe clamp nut 55 Nm 41 lbf.ft

MAINTENANCE
10-4 MAINTENANCE
Seats and Seat Belts
Check
1.Check seat frames are secured to floor and
show no signs of movement.
2.Check operation of seat slide and tilt
mechanisms, ensuring there is no excessive
play between seat cushion and seat back.
3.Check tightness of accessible seat fixings.
4.Fully extract seat belt and allow it to return
under its own recoil mechanism.
5.Check entire length of seat belt webbing for
signs of fraying or damage. Repeat for all belts.
6.Check security of seat belt upper mountings.
7.Check for correct operation of seat belt height
adjusters.
8.Check security of seat belt buckle mountings.
9.Connect each belt to the correct buckle, check
seat belt buckle and tongue are secure.
Release seat belt buckle and check for correct
operation.
10.Check tightness of accessible seat belt
mountings.
Lamps, Horns and Warning Indicators
Check
1.Switch on side, head and tail lights and check
operation.
2.Check headlamp dim/dip operation.
3.Check headlamp levelling operation.
4.Check turn signals and hazard warning lights
operation.
5.Press brake pedal and check operation of
brake lights.
6.Check all exterior lamp lenses for clarity and
condition. Pay particular attention to head lamp
lenses for signs of stone chips or damage.
7.Check horn for loud clear sound.
8.Check operation of all instrument pack warning
and indicator lights.
9.Check for correct operation of interior courtesy
lights.
10.Switch on headlamps (with ignition switch at 'O'
position) and check light reminder warning
operates when door is opened.

ENGINE - K SERIES KV6
REPAIRS 12-3-13
Cylinder head gasket - LH
$% 12.29.02
Remove
1.Disconnect battery earth lead.
2.Drain cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
3.Remove inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
4.Remove LH exhaust manifold gasket.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket - exhaust
manifold - LH - Non NAS.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket(s) -
exhaust manifold - LH - NAS.
5.Remove camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
6.Remove 4 bolts securing LH front camshaft
timing belt cover backplate to cylinder head;
remove backplate.
7.Remove LH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.8.Remove 3 nuts and 3 bolts securing ignition
coils to LH inlet manifold and release coil earth
lead, if fitted.
9.Remove ignition coils and position aside, if
fitted.
10.Release clip and disconnect coolant bleed
hose from inlet manifold and move hose aside.
11.Depress locking collar and release breather
hose from LH inlet manifold.

ENGINE - K SERIES KV6
REPAIRS 12-3-15
Refit
1.Clean cylinder head mating face.
CAUTION: Use suitable gasket removal
spray and a plastic scraper.
2.Remove bolts securing cylinder liner clamps
LRT-12-144 to cylinder block and remove
clamps.
CAUTION: Do not rotate crankshaft.
3.Clean cylinder block face and dowel holes.
4.Clean cylinder head bolts and wipe dry.
5.Lightly lubricate threads and beneath heads of
cylinder head bolts with clean engine oil.
6.Check that fitted height of dowels is between 10
to 11 mm (0.40 to 0.43 in) above cylinder block
top face. Replace dowels if fitted height is
incorrect.
7.Fit new cylinder head gasket onto cylinder
block with the word 'TOP' uppermost.
8.With assistance, fit cylinder head and carefully
position LH inlet to RH inlet manifold.
9.Carefully enter cylinder head bolts, DO NOT
DROP. Screw bolts into place by hand.10.Tighten cylinder head bolts progressively in the
sequence shown to :
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 3 -Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 4 - Using an angle torque gauge,
tighten bolts in the same sequence a further
180°
11.Fit LH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.
12.Remove and discard 'O' rings from injectors.
13.Clean injectors and injector locations in fuel rail.
14.Lubricate new 'O' rings with castor oil and fit to
injectors.
15.Position fuel rail assembly and secure injectors
to inlet manifolds.
16.Position injector protection cover - if fitted to RH
fuel rail and secure injector harness to
protection cover or fuel rail with clips.
17.Fit bolts securing fuel rail to inlet manifolds and
tighten to 9 Nm (7 lbf.ft).
18.Position CMP sensor bracket, fit and tighten
bolt to 9 Nm (7 lbf.ft).
19.Connect CMP sensor multiplug and secure to
bracket.
20.Connect breather hose to LH inlet manifold.
21.Connect coolant bleed hose to inlet manifold
and secure with clip.
22.Position ignition coils to LH inlet manifold.
23.Position earth lead, fit nuts and bolts securing
ignition coils to LH inlet manifold and tighten to
9 Nm (7 lbf.ft).
24.Position ht lead guide bracket, fit and tighten
special bolt.
25.Connect ht leads to spark plugs and secure ht
leads in guide clips.
26.Clean camshaft timing belt cover backplate
bolts and apply sealant, Part No. STC 50552 to
the first 3 threads.

ENGINE - K SERIES KV6
REPAIRS 12-3-19
10.Tighten cylinder head bolts progressively in the
sequence illustrated to:
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 3 -Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 4 - Using an angle torque gauge,
tighten bolts in the same sequence a further
180°
11.Fit RH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - RH.
12.Remove and discard lower 'O' rings from
injectors.
13.Clean injectors and injector locations in fuel rail.
14.Lubricate new 'O' rings with castor oil and fit to
injectors.
15.Position fuel rail assembly and secure injectors
to inlet manifolds.
16.Position injector protection cover - if fitted to RH
fuel rail; secure injector harness to protection
cover or fuel rail with clips.
17.Fit bolts securing fuel rail to inlet manifolds and
tighten to 9 Nm (7 lbf.ft).
18.Connect coolant bleed hose to inlet manifold
and secure with clip.
19.Connect breather hoses to RH camshaft cover
and inlet manifold.
20.Position ignition coils to LH inlet manifold.
21.Position earth lead, fit nuts and bolts securing
ignition coils to LH inlet manifold and tighten to
9 Nm (7 lbf.ft).
22.Connect multiplugs to plug top coils and secure
with locking clips.
23.Clean camshaft timing belt cover backplate
bolts and apply sealant, Part No. STC 50552 to
the first 3 threads.
24.Position backplate, fit and tighten bolts to 9 Nm
(7 lbf.ft).25.Fit camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
26.Fit RH exhaust manifold gasket.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket - exhaust
manifold - RH - Non NAS.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket(s) -
exhaust manifold - RH - KV6 - NAS.
27.Fit inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
28.Fill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
29.Check engine oil level and top-up if necessary.

+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.

ENGINE - K SERIES KV6
REPAIRS 12-3-21
Refit
1.Clean mating surfaces of camshaft cover and
carrier.
2.Clean inside of camshaft cover. If necessary,
wash oil separator elements in solvent and
blow dry.
3.Position new gasket to camshaft carrier with
arrows on gasket pointing towards inlet
manifold.
4.Position camshaft cover, fit and tighten bolts
progressively in the sequence shown to 9 Nm
(7 lbf.ft).
5.Position multiplug bracket, fit and tighten bolt to
9 Nm (7 lbf.ft).
6.Secure male end of CMP sensor multiplug to
bracket and connect multiplug.
7.Connect ht leads to spark plugs in their correct
fitted order.
8.Position ht lead guide bracket, fit and tighten
special bolt.
9.Connect breather hoses to LH camshaft cover.
10.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
11.Check engine oil, top-up if necessary.

+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.
Camshaft cover gasket - LH - from 03MY
$% 12.29.40
Remove
1.Remove the engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2.Depress locking collars and release 2 breather
hoses from LH camshaft cover.
3.Remove acoustic cover retainer and remove
plug top coil harness clip.
4.Disconnect CMP sensor multiplug and release
male end of multiplug from bracket.