glove box LAND ROVER FREELANDER 2001 User Guide

INTERIOR TRIM COMPONENTS
76-3-22 REPAIRS
29.Noting fitted position remove fascia harness
assembly.Refit
1.Fit and secure fascia harness.
2.Fit striker plate, secure with screws and adjust
if necessary.
3.Fit passenger side glove box assembly.
4.Fit face level air vents.
5.Fit and secure cruise switch carrier assembly to
fascia.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Switch - engagement
(on/off) - from 04MY.
6.Fit glove box lids and secure hinge pins.
7.Connect mirror switch multiplug and fit switch
assembly to fascia.
8.Fit switches to fascia carrier and connect
multiplugs.
9.With assistance fit fascia to vehicle and secure
bolts to 10 Nm (7 lbf.ft).
10.Connect fascia harness multiplugs to main
harness.
11.Fit passenger airbag.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - fascia - passenger - from 04MY.
12.Fit 'A' post upper trim finishers.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
13.Fit hazard warning switch.

+ DRIVER CONTROLS, REPAIRS,
Switch - hazard warning - from 04MY.
14.Fit clock.

+ INSTRUMENTS, REPAIRS, Clock.
15.Open drivers side glove box.
16.Fit Radio/CD module.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio/CD - from 04MY.
17.Fit fuse box cover and close glove box lid.
18.Fit steering column lower cover and secure with
screws.
19.Fit wiper/indicator switch and tighten clamping
screw.
20.Connect multiplugs to wiper/indicator switch.
21.Fit rotary coupler.

+ RESTRAINT SYSTEMS, REPAIRS,
Rotary coupler - (SRS) air bag system.
22.Fit heater control to fascia and secure with
screws.
23.Fit instrument pack.

+ INSTRUMENTS, REPAIRS,
Instrument panel - from 04MY.
M76 4721

INTERIOR TRIM COMPONENTS
REPAIRS 76-3-25
Glove box
$% 76.52.03
Remove
1.Open glove box and remove glove box mat.
2.Release illumination lamp from glove box.
3.Remove 4 screws from glove box and remove
glove box.
Refit
1.Fit glove box and secure with screws.
2.Fit illumination lamp.
3.Fit glove box mat.
4.Close glove box.
Headlining - 3 door
$% 76.64.15
Remove
1.Fold front seat squabs forward.
2.Remove both sun visors.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.
3.Remove both 'A' post upper trim finishers.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
4.Remove 2 screws securing headlining to front
end of roof panel.

PANEL REPAIRS
WELDING PROCEDURES 77-2-15
WE LDING PROCEDURE S
ECU locations (3 door model shown, 5
door model similar)
1Central control unit (on forward side of
passenger compartment fusebox, behind
driver's glove box)
2RF Receiver (on top of instrument pack)
3Immobiliser ECU (rear of fascia)
4DCU (SRS on transmission tunnel below
heater)
5EAT ECU (inside Environmental 'E' box)
6ECM (inside 'E' box)
7Fuel Burning Heater (behind wheelarch liner)
'Diesel only'8Cooling Fan Ecu (rear of radiator housing) all
models except 1.8
9ABS ECU (RH side front of engine
compartment)
10Folding door mirror ECU (on transmission
tunnel under centre console)
11Window lift ECU (on driver `A` post)
12Cruise Control Interface ECU (under R/H seat)
13Cruise control ECU (under R/H seat)

HEATING AND VENTILATION
REPAIRS 80-3
Servo - air recirculation
$% 80.10.18
Remove
1.Remove glove box.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Glove box.
2.Disconnect multiplug from servo.
3.Remove screw securing servo to evaporator
and remove servo.
Refit
1.Fit servo to evaporator and secure with screw.
2.Connect multiplug to servo.
3.Fit glove box.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Glove box.
Switch - recirculation control
$% 80.10.21
Remove
1.Remove 3 heater control knobs.
2.Remove 2 screws securing heater control
finisher to heater controls and remove finisher.
3.Release switch and disconnect multiplug.
4.Remove switch.
Refit
1.Fit recirculation switch to heater control panel
and connect multiplug.
2.Fit heater control finisher to heater controls and
secure with screws.
3.Fit heater control knobs.

LIGHTING
86-2-8 REPAIRS
Lamp assembly - glove compartment
$% 86.45.08
Remove
1.Open glove box.
2.Release illumination lamp from glove box.
3.Disconnect 2 Lucars and remove glove box
lamp.
Refit
1.Position lamp and connect Lucars.
2.Fit lamp and close glove box.
Lamp assembly - load space
$% 86.45.16
Remove
1.Release load space lamp from trim casing.
2.Disconnect 2 Lucars and remove load space
lamp.
Refit
1.Position lamp and connect Lucars.
2.Fit load space lamp to trim casing.

LIGHTING
REPAIRS 86-2-9
Switch - headlamp levelling
$% 86.65.16
Remove
1.Release headlamp levelling switch from fascia
and disconnect multiplug.
Refit
1.Position switch, connect multiplug and secure
switch to fascia.
Switch - glove compartment
$% 86.65.24
Remove
1.Remove glove box.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Glove box.
2.Disconnect 2 Lucars from glove box lamp
switch.
3.Release clips and remove switch from glove
box latch.
Refit
1.Fit switch to glove box latch and connect
Lucars.
2.Fit glove box.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Glove box.

CONTROL UNITS
86-3-2 REPAIRS
Central Control Unit (CCU)
$% 86.55.75
Remove
1.Disconnect battery earth lead.
2.Open drivers glove box lid and remove fuse box
cover.
3.Remove bolt securing fuse box mounting plate
to steering column bracket.
4.Remove 2 bolts securing mounting plate to
body.
5.Remove 2 bolts securing fuse box to mounting
plate.
6.Disconnect 3 multiplugs from CCU in rear of
fuse box.

CONTROL UNITS
REPAIRS 86-3-3
7.Manoeuvre fuse box to gain access to CCU.
8.Release retaining clips and remove CCU.
Refit
1.Position CCU and secure in clips.
2.Align fuse box to mounting plate.
3.Connect multiplugs to CCU.
4.Fit bolts securing fuse box to mounting bracket
and tighten to 8 Nm (6 lbf.ft).
5.Position mounting plate and tighten bolts to 8
Nm (6 lbf.ft).
6.Fit fuse box cover.
7.Close glove box.
8.Connect battery earth lead.
Control Unit - power fold mirrors - up to
02MY
$% 86.54.30
CAUTION: If the power fold mirrors are operated
consecutively more than three times, then they
will cease to function for a period of one minute.
This is to prevent damage to the power fold
mirror motors.
Remove
1.Remove the front console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - front - up to 04MY.
2.Release the two clips securing the power fold
mirror control unit.
3.Release the control unit from its mounting and
disconnect the multiplug.
4.Remove the control unit.
Refit
1.Locate the control unit in its mounting and
ensure the clips are fully engaged.
2.Connect the multiplug to the control unit.
3.Fit the front console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - front - up to 04MY.
M86 5689

HARNESSES
REPAIRS 86-7-1
HARNESSES REPAIRS
Fuse box - passenger compartment
$% 86.70.01
Remove
1.Disconnect battery earth lead.
2.Open glove box.
3.Remove hinge pins and lid.
4.Remove fuse box cover.
5.Remove relays from fuse box mounting plate.
6.Remove bolt securing fuse box mounting plate
to steering column bracket.
7.Remove 2 bolts securing mounting plate to
body.
8.Remove 2 bolts securing fuse box to mounting
plate.
9.Disconnect 3 multiplugs from CCU in rear of
fuse box.
10.Release fusebox and disconnect 8 multiplugs.
11.Remove fusebox.
12.Remove fuses and relays from fuse box.Refit
1.Identify and fit fuses.
2.Fit relays.
3.Fit fuse box.
4.Connect multiplugs to fusebox.
5.Connect multiplugs to CCU.
6.Fit bolts securing fuse box to mounting plate
and tighten to 8 Nm (6 lbf.ft).
7.Fit bolts securing fuse box mounting plate to
body and tighten to 8 Nm (6 lbf.ft).
8.Fit relays to mounting plate.
9.Fit fuse box cover.
10.Fit glove box lid and hinge pins.
11.Close lid.
12.Connect battery earth lead.