wiper fluid LAND ROVER FREELANDER 2001 User Guide

PANEL REPAIRS
REPAIRS 77-2-37
Valance front
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
6.Remove engine bay shield.
7.Remove front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
8.Remove front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
9.Remove front bumper support bracket.
10.Remove radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
11.Remove headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
12.Release wiring to headlamp and position aside.
13. LH side: Remove air cleaner.
14. LH side: Remove air intake hose.
15. LH side: Remove ECM.
16. LH side: Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
17. LH side: Remove engine compartment fuse
box and related wiring.
18. LH side: Remove LH front brake pipe.
19. RH side: Remove PAS fluid reservoir.
20. RH side: Remove RH front brake pipe.
21. RH side: Remove windscreen washer
reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
22. RH side: Remove PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.

PANEL REPAIRS
77-2-38 REPAIRS
Refit
1. LH side: Fit LH front brake pipe. Bleed brake
system.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
2. LH side: Fit engine compartment fuse box and
related wiring.
3. LH side: Fit battery carrier. Do not connect
battery earth lead.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
4. LH side: Fit ECM.
5. LH side: Fit air intake hose.
6. LH side: Fit air cleaner.
7. RH side: Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
8. RH side: Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
9. RH side: Fit RH front brake pipe. Bleed brake
system.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
10. RH side: Fit PAS fluid reservoir.
11.Fit headlamp.

+ LIGHTING, REPAIRS, Headlamp
assembly - up to 04MY.
12.Secure headlamp wiring.
13.Fit PAS fluid cooler.

+ STEERING, REPAIRS, Oil cooler -
Td4 & K1.8 models.
14.Fit radiator.

+ COOLING SYSTEM - K SERIES KV6,
REPAIRS, Radiator assembly.
15.Fit front bumper support bracket.
16.Fit front bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
17.Fit front wing.

+ EXTERIOR FITTINGS, REPAIRS,
Wing - front.
18.Fit front wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - front wheel arch.
19.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
20.Connect all ECUs.
21.Connect alternator.
22.Connect battery earth lead.

WIPERS AND WASHERS
REPAIRS 84-1
WIPERS AND WASHERS REPAIRS
Reservoir - washer
$% 84.10.01
Remove
1.Remove front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
2.Position container to collect fluid loss.
3.Remove 2 nuts securing reservoir filler neck
and remove filler neck.
4.Release both washer pumps from reservoir.
5.Remove and discard pump sealing grommets.
6.Remove 3 bolts securing washer reservoir and
remove.Refit
1.Fit reservoir and secure with bolts.
2.Fit new pump sealing grommets to reservoir.
3.Fit pumps to reservoir.
4.Fit filler neck and secure with nuts.
5.Fit front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.

WIPERS AND WASHERS
84-2 REPAIRS
Jet - washer - each
$% 84.10.08
Remove
1.Disconnect tube from washer jet.
2.Depress plastic lugs and remove washer jet
from bonnet.
Refit
1.Fit washer jet to bonnet and connect tube.
2.Adjust jet so the inside spray is to centre of the
screen, and the outer spray is to the top of the
screen.
Pump - washer
$% 84.10.21
Remove
1.Remove front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
2.Position container to catch windscreen washer
fluid.
3.Disconnect multiplug and hose from
windscreen washer pump.
4.Release pump from reservoir.
5.Remove and discard pump sealing grommet.
Refit
1.Fit new pump sealing grommet to reservoir.
2.Fit pump to reservoir.
3.Connect hose and multiplug to pump.
4.Fit front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.

WIPERS AND WASHERS
REPAIRS 84-5
Pump - washer
$% 84.30.21
Remove
1.Remove front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
2.Position container to catch windscreen washer
fluid.
3.Disconnect multiplug from washer pump.
4.Release hose from pump.
5.Remove washer pump from reservoir and
remove and discard pump seal.
Refit
1.Fit new pump sealing grommet to reservoir.
2.Fit pump to reservoir.
3.Connect hose and multiplug to pump.
4.Fit front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
Arm - wiper
$% 84.35.01
Remove
1.Remove wiper blade.

+ WIPERS AND WASHERS, REPAIRS,
Blade - wiper.
2.Remove spare wheel mounting bracket.

+ EXTERIOR FITTINGS, REPAIRS,
Bracket - spare wheel mounting.
3.Raise nut cover on wiper arm and remove nut.
4.Release washer jet tube and remove wiper
arm.
NOTE: Do not carry out further dismantling if
component is removed for access only.
5.Release washer jet and washer jet tube from
wiper arm.
Refit
1.Position and secure washer tube and jet to
wiper arm.
2.Position wiper arm to tail door and connect
washer tube.
3.Set wiper arm with tip contacting joint line
between waist seal and rear door. Fit and
tighten wiper arm nut to 13 Nm (10 lbf.ft).
4.Fit wiper blade.

+ WIPERS AND WASHERS, REPAIRS,
Blade - wiper.
5.Fit spare wheel mounting bracket.

+ EXTERIOR FITTINGS, REPAIRS,
Bracket - spare wheel mounting.

HARNESSES
86-7-2 REPAIRS
Harness - main
$% 86.70.07
Remove
1.Make the SRS system safe.

+ GENERAL INFORMATION,
Supplementary restraint system
precautions.
2.Remove carpet.
3.Remove engine acoustic cover.

+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
4.Remove windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
5.Pull reservoir harness and washer tubes into
engine bay.
6.Remove nut and release earth header from RH
inner wing.
7.Disconnect multiplug from ABS modulator.
8.Disconnect multiplug from RH ABS speed
sensor and release harness from clips.
9.Disconnect 2 multiplugs from RH headlamp
and headlamp levelling motor.10.Disconnect multiplugs from horn, refrigerant
pressure sensor and compressor.
11.Remove jack from holder in engine bay.
12.Disconnect multiplug from brake fluid low level
indicator switch.
13.Disconnect multiplug from bonnet switch.
14.Remove bolt and 2 nuts securing PAS and
coolant reservoir support bracket and position
aside.
15.Release 5 harness retaining clips.
16.Release front screen wash tube from harness
and position aside.
17.Remove nut securing earth header to bulk head
and remove earth header.

HARNESSES
REPAIRS 86-7-11
41.Position fuse box to body and connect
multiplugs.
42.Fit relays to fuse box bracket.
43.Connect coaxial cable.
44.Fit and connect multiplug to RH 'A' post.
45.Fit passenger compartment fuse box and
secure with bolts.
46.Position side repeater lamps, connect
multiplugs and fit to wings.
47.Secure rear edge of front wheel arch liners.
48.Fit front mud flaps and secure with screws.
49.With assistance feed harness through bulk
head into engine bay.
50.Position harness to wiper motor and connect
multiplug.
51.Fit air intake plenum.

+ HEATING AND VENTILATION,
REPAIRS, Plenum - air intake.
52.Secure harness to LH side of engine bay and
secure fixings.
53.Connect multiplug to inertia switch.
54.Connect multiplugs to underside of fuse box.
55.Fit nuts securing fuse box to brackets.
56.Fit battery connections and multiplug to fuse
box.
57.Fit fuse box cover.
58.Connect 'E' box cooling fan multiplug.
59.Connect 'E' box temperature sensor multiplug.
60.Connect engine harness multiplugs to main
harness.
61. Automatic gearbox only:Connect multiplug to
gearbox ECU.
62.Fit 'E' box cover and secure with Allen screws.
63.Connect engine harness multiplugs to main
harness.
64.Fit harness retaining clips.
65. Models with cruise control: Connect
multiplug to vacuum pump.
66.Connect Lucar connector to starter motor.
67.Connect multiplug to LH ABS speed sensor.
68.Fit LH earth header and secure with nut.
69.Connect multiplug to harness.
70.Connect multiplugs to LH headlamp and
headlamp levelling motor.
71.Secure harness to cooling fan clips.
72.Connect multiplugs to cooling fan pack and
cooling fans.
73.Position bonnet release cable to harness and
secure with cable ties.
74.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
75.With assistance feed harness through bulk
head into engine bay.
76.Fit earth header to bulk head and secure with
nut.
77.Fit front screen washer tube to harness.
78.Fit harness retaining clips.79.Fit PAS and coolant reservoir support bracket
and secure with bolt and nuts.
80.Connect multiplug to bonnet switch.
81.Connect multiplug to brake fluid low level
indicator switch.
82.Fit jack to holder in engine bay.
83.Connect multiplugs to horn, refrigerant
pressure sensor and compressor.
84.Connect multiplugs to RH headlamp and
headlamp levelling motor.
85.Connect multiplug to RH ABS speed sensor
and secure to clips.
86.Connect multiplug to ABS modulator.
87.Fit earth header to RH inner wing and secure
with nut.
88.Position harness to windscreen washer
reservoir.
89.Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
90.Fit engine acoustic cover.

+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
91.Fit carpet.