wipers LAND ROVER FREELANDER 2001 Owner's Manual

WIPERS AND WASHERS
84-4 REPAIRS
Motor & linkage - wiper
$% 84.15.11
Remove
1.Remove air intake moulding.

+ HEATING AND VENTILATION,
REPAIRS, Plenum - air intake.
2.Disconnect multiplug from windscreen wiper
motor.
3.Remove 3 bolts securing wiper motor and
linkage to body and remove wiper motor and
linkage.
Refit
1.Fit motor and linkage to body, fit bolts and
tighten to 5 Nm (3.5 lbf.ft).
2.Connect multiplug to windscreen wiper motor.
3.Fit air intake moulding.

+ HEATING AND VENTILATION,
REPAIRS, Plenum - air intake.
Switch - wiper/washer
$% 84.15.34
Remove
1.Remove rotary coupler.

+ RESTRAINT SYSTEMS, REPAIRS,
Rotary coupler - (SRS) air bag system.
2.Disconnect multiplug from washer and wiper
switch.
3.Release multiplug connector from switch base
on steering column.
4.Disconnect multiplug from connector.
5.Remove 2 screws from wiper switch.
6.Depress retaining tag and remove switch.
Refit
1.Fit washer and wiper switch assembly and
secure with screws.
2.Connect multiplugs to switch.
3.Secure multiplug to steering column.
4.Fit rotary coupler.

+ RESTRAINT SYSTEMS, REPAIRS,
Rotary coupler - (SRS) air bag system.

WIPERS AND WASHERS
REPAIRS 84-5
Pump - washer
$% 84.30.21
Remove
1.Remove front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
2.Position container to catch windscreen washer
fluid.
3.Disconnect multiplug from washer pump.
4.Release hose from pump.
5.Remove washer pump from reservoir and
remove and discard pump seal.
Refit
1.Fit new pump sealing grommet to reservoir.
2.Fit pump to reservoir.
3.Connect hose and multiplug to pump.
4.Fit front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
Arm - wiper
$% 84.35.01
Remove
1.Remove wiper blade.

+ WIPERS AND WASHERS, REPAIRS,
Blade - wiper.
2.Remove spare wheel mounting bracket.

+ EXTERIOR FITTINGS, REPAIRS,
Bracket - spare wheel mounting.
3.Raise nut cover on wiper arm and remove nut.
4.Release washer jet tube and remove wiper
arm.
NOTE: Do not carry out further dismantling if
component is removed for access only.
5.Release washer jet and washer jet tube from
wiper arm.
Refit
1.Position and secure washer tube and jet to
wiper arm.
2.Position wiper arm to tail door and connect
washer tube.
3.Set wiper arm with tip contacting joint line
between waist seal and rear door. Fit and
tighten wiper arm nut to 13 Nm (10 lbf.ft).
4.Fit wiper blade.

+ WIPERS AND WASHERS, REPAIRS,
Blade - wiper.
5.Fit spare wheel mounting bracket.

+ EXTERIOR FITTINGS, REPAIRS,
Bracket - spare wheel mounting.

WIPERS AND WASHERS
84-6 REPAIRS
Blade - wiper
$% 84.35.02
Remove
1.Lift wiper arm from tail door glass.
2.Remove wiper blade from arm.Refit
1.Position new blade to wiper arm.
2.Secure blade in retainer.
3.Position blade to glass.

WIPERS AND WASHERS
REPAIRS 84-7
Motor - wiper
$% 84.35.12
Remove
1.Remove rear wiper arm.

+ WIPERS AND WASHERS, REPAIRS,
Arm - wiper.
2.Remove tail door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
tail door.
3.Remove spindle nut and flat washer and
discard rubber seal.
4.Disconnect multiplug from rear wiper motor.
5.Remove 2 bolts securing wiper motor to tail
door.
6.Remove wiper motor.
NOTE: Do not carry out further dismantling if
component is removed for access only.7.Remove and discard spindle sealing washer.
8.Remove motor water shield.
9.Remove 3 bolts securing mounting plate to
wiper motor.
10.Release multiplug and remove mounting plate.
Refit
1.Position mounting plate, tighten bolts and
secure multiplug.
2.Fit motor water shield and new sealing washer
to spindle.
3.Fit wiper motor and tighten bolts to 5 Nm (3.5
lbf.ft).
4.Connect multiplug to rear wiper motor.
5.Fit NEW rubber seal to wiper motor spindle.
6.Fit flat washer and tighten spindle nut to 5 Nm
(3.5 lbf.ft).
7.Fit tail door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
tail door.
8.Fit wiper arm.

+ WIPERS AND WASHERS, REPAIRS,
Arm - wiper.

WIPERS AND WASHERS
84-8 REPAIRS
Switch - combined wiper/washer
$% 84.35.34
Remove
1.Remove instrument cowl.

+ INSTRUMENTS, REPAIRS, Cowl -
instrument - up to 04MY.
2.Remove rear wiper switch from instrument
cowl.
Refit
1.Fit switch to instrument cowl.
2.Fit instrument cowl.

+ INSTRUMENTS, REPAIRS, Cowl -
instrument - up to 04MY.
Relay - tailgate wipe - 5 door
$% 84.35.38
Remove
1.Remove RH rear quarter lower trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
2.Remove rear wiper motor relay.
Refit
1.Fit rear wiper motor relay.
2.Fit RH rear quarter lower casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.

HARNESSES
86-7-2 REPAIRS
Harness - main
$% 86.70.07
Remove
1.Make the SRS system safe.

+ GENERAL INFORMATION,
Supplementary restraint system
precautions.
2.Remove carpet.
3.Remove engine acoustic cover.

+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
4.Remove windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
5.Pull reservoir harness and washer tubes into
engine bay.
6.Remove nut and release earth header from RH
inner wing.
7.Disconnect multiplug from ABS modulator.
8.Disconnect multiplug from RH ABS speed
sensor and release harness from clips.
9.Disconnect 2 multiplugs from RH headlamp
and headlamp levelling motor.10.Disconnect multiplugs from horn, refrigerant
pressure sensor and compressor.
11.Remove jack from holder in engine bay.
12.Disconnect multiplug from brake fluid low level
indicator switch.
13.Disconnect multiplug from bonnet switch.
14.Remove bolt and 2 nuts securing PAS and
coolant reservoir support bracket and position
aside.
15.Release 5 harness retaining clips.
16.Release front screen wash tube from harness
and position aside.
17.Remove nut securing earth header to bulk head
and remove earth header.

HARNESSES
REPAIRS 86-7-11
41.Position fuse box to body and connect
multiplugs.
42.Fit relays to fuse box bracket.
43.Connect coaxial cable.
44.Fit and connect multiplug to RH 'A' post.
45.Fit passenger compartment fuse box and
secure with bolts.
46.Position side repeater lamps, connect
multiplugs and fit to wings.
47.Secure rear edge of front wheel arch liners.
48.Fit front mud flaps and secure with screws.
49.With assistance feed harness through bulk
head into engine bay.
50.Position harness to wiper motor and connect
multiplug.
51.Fit air intake plenum.

+ HEATING AND VENTILATION,
REPAIRS, Plenum - air intake.
52.Secure harness to LH side of engine bay and
secure fixings.
53.Connect multiplug to inertia switch.
54.Connect multiplugs to underside of fuse box.
55.Fit nuts securing fuse box to brackets.
56.Fit battery connections and multiplug to fuse
box.
57.Fit fuse box cover.
58.Connect 'E' box cooling fan multiplug.
59.Connect 'E' box temperature sensor multiplug.
60.Connect engine harness multiplugs to main
harness.
61. Automatic gearbox only:Connect multiplug to
gearbox ECU.
62.Fit 'E' box cover and secure with Allen screws.
63.Connect engine harness multiplugs to main
harness.
64.Fit harness retaining clips.
65. Models with cruise control: Connect
multiplug to vacuum pump.
66.Connect Lucar connector to starter motor.
67.Connect multiplug to LH ABS speed sensor.
68.Fit LH earth header and secure with nut.
69.Connect multiplug to harness.
70.Connect multiplugs to LH headlamp and
headlamp levelling motor.
71.Secure harness to cooling fan clips.
72.Connect multiplugs to cooling fan pack and
cooling fans.
73.Position bonnet release cable to harness and
secure with cable ties.
74.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
75.With assistance feed harness through bulk
head into engine bay.
76.Fit earth header to bulk head and secure with
nut.
77.Fit front screen washer tube to harness.
78.Fit harness retaining clips.79.Fit PAS and coolant reservoir support bracket
and secure with bolt and nuts.
80.Connect multiplug to bonnet switch.
81.Connect multiplug to brake fluid low level
indicator switch.
82.Fit jack to holder in engine bay.
83.Connect multiplugs to horn, refrigerant
pressure sensor and compressor.
84.Connect multiplugs to RH headlamp and
headlamp levelling motor.
85.Connect multiplug to RH ABS speed sensor
and secure to clips.
86.Connect multiplug to ABS modulator.
87.Fit earth header to RH inner wing and secure
with nut.
88.Position harness to windscreen washer
reservoir.
89.Fit windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
90.Fit engine acoustic cover.

+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
91.Fit carpet.