door lock LAND ROVER FREELANDER 2001 Owner's Guide

CORROSION PREVENTION AND SEALING
77-4-28 INTERNAL SEALING
5 Door shown
Expanding foam acoustic seals
Expanding foam acoustic seals are used in various closed sections of the body to improve vehicle refinement. The
seals expand during the factory paint process, thus locking them into position. The seals are used in various locations
throughout the vehicle.
The main function of the seals is to insulate the cabin from noise and vibrations, particularly road noise. They are
located such that they prevent noise accentuation along a section and also reflect air borne noise away from the cabin.
A secondary function of the seals is that the internal sections are sealed from the infiltration of water, air, dust and
gases.
Another advantage of the seals is that they marginally increase the overall stiffness of the body and its structural
performance in case of a crash.
The seals are manufactured from an expandable synthetic rubber, `Betacore 4300`.
All the seals are fitted in the body-in-white areas, and after going through the paint baking process expand up to eight
times original size.
M77 2057

WINDOWS
86-5-2 REPAIRS
Motor & control unit - front door - 5 door
$% 86.25.01
Remove
1.Remove front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.
2.Disconnect multiplug from door glass motor.
3.Loosen 2 screws clamping control unit to glass.
4.Release cable from door clip.
5.Remove 5 screws securing control unit to door.
6.Release cable from door clip and manoeuvre
motor and control unit out from door aperture.
Refit
1.Position motor and control unit in door aperture
and locate to glass.
CAUTION: It is very important when fitting
the control unit that the cable with the anti-
rattle sleeve is next to the trim casing and
the motor cable next to the glass.
2.Fit and tighten screws securing control unit to
door.
3.Secure cable in door clip.
4.Tighten clamps securing control unit to glass, to
9 Nm (7 lbf.ft).
5.Connect multiplug to door glass motor.
6.Fit front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.
Switch - master window - 5 door - from
04MY
$% 86.25.08
The procedure to remove the window lift and door
panic lock switches is similar to the one shown
below.
Remove
1.Carefully release window lift switch pack from
door trim casing.
2.Disconnect 3 multiplugs from window lift switch
pack and remove switch pack.
NOTE: Do not carry out further dismantling if
component is removed for access only.
3.Carefully release and remove window lift switch
pack from bezel.
Refit
1.Fit window lift switch pack to bezel.
2.Position switch pack, connect multiplugs and
secure switch pack to trim casing.
M76 4698

HARNESSES
REPAIRS 86-7-13
11.Disconnect 2 Lucars from rear screen element.
12.Remove 4 screws from door latch, release door
latch to access multiplugs and harness clips.
13.Disconnect 2 multiplugs from door lock.14.Disconnect multiplug from rear wiper motor.
15.Disconnect multiplug from rear window motor.
16.Release and disconnect 3 multiplugs and
washer tube from main harness at 'E' post.

HARNESSES
86-7-14 REPAIRS
17.Release tail door harness from 13 retaining
clips.
18.Release harness sheath from tail door and 'E'
post.
19.Remove harness from vehicle.Refit
1.Position harness to vehicle and secure in
retaining clips.
2.Secure harness sheath to tail door and 'E' post.
3.Connect multiplugs and washer tube to main
harness, secure multiplugs to body.
4.Connect multiplugs to window motor, wiper
motor and door lock.
5.Position door latch, fit and tighten screws.
6.Connect Lucars to heated rear screen.
7.Position number plate lamp housing, locate
seal and fit spacers.
8.Connect multiplug and Lucars to housing.
9.Fit housing and secure with nuts.
10.Connect washer tube behind spare wheel
carrier.
11.Secure harness clips to spare wheel carrier,
connect multiplug to CHMSL, fit CHMSL and
secure with screws.
12.Fit spare wheel and secure with nuts.
13.Fit tail door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
tail door.
14.Fit rear lower trim casing .

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.

HARNESSES
REPAIRS 86-7-15
Harness - interior lights - 5 door
$% 86.70.44
Remove
1.Remove fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
2.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
3.Disconnect aerial connection and interior light
harness from main harness.
4.Disconnect multiplug from volumetric sensor.
5.Release 10 harness clips.
6.Remove harness.
Refit
1.Position harness and secure harness clips.
2.Connect multiplug to volumetric sensor.
3.Connect multiplug and aerial connection to
main harness.
4.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
5.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
Harness - front door - 5 door
$% 86.70.65
Remove
1.Remove front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.
2.Disconnect multiplugs from door lock, door
mirror and window motor.
3.Release 8 clips securing door harness to door.
4.Release 2 multiplugs from location at base of
'A' post and disconnect multiplugs.
5.Release sheath from front edge of door, and
pull harness from door.
6.Release sheath from 'A' post and pull harness
from 'A' post.
7.Remove door harness.
Refit
1.Position harness to 'A' post and feed harness
partly into 'A' post.
2.Feed sheath onto harness and locate sheath to
'A' post.
3.Feed harness through front edge of door and
secure sheath to door.
4.Connect and secure multiplugs at base of 'A'
post.
5.Position harness to door and secure with clips.
6.Connect multiplugs to door mirror, door lock
and window motor.
7.Fit front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.

INSTRUMENTS
88-8 REPAIRS
Refit
1.Clean fuel tank sender assembly and mating
face.
2.Fit new fuel tank sender assembly seal to fuel
tank.
3.Fit fuel tank sender assembly to fuel tank.
4.Using LRT-19-009 fit and secure fuel tank
sender assembly locking ring to fuel tank.
5. Models with FBH: Connect FBH hose to fuel
tank sender assembly and secure with clip.
6.Fit and secure pressure relief, fuel feed and
return hoses to fuel tank sender assembly.
7.Remove container from beneath fuel tank.
8.Connect multiplug to fuel tank sender
assembly.
9.Fit fuel tank sender assembly access panel and
secure with screws.
10.Position carpet to floor and secure with
fasteners.
11.Reposition rear seat.
12.Close rear and tail doors.
13.Connect battery earth lead.