wheel bolts LAND ROVER FREELANDER 2001 Manual Online

BRAKES
REPAIRS 70-23
Carrier assembly - calliper - front
$% 70.55.28
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Remove 2 guide pins from calliper housing.
4.Release calliper housing from calliper carrier
and tie aside.
5.Remove 2 brake pads and retainers from
calliper carrier.6.Remove 2 bolts securing calliper carrier and
remove carrier.
7.Remove guide pins and seals from carrier.

BRAKES
70-24 REPAIRS
Refit
1.Clean guide pins and carrier mating faces.
2.Fit guide pins and seals to carrier.
3.Fit carrier, fit bolts and tighten to 100 Nm (74
lbf.ft).
4.Rotate disc by hand and scrape all scale and
rust from around edge of disc. Clean location
surfaces on calliper bracket.
5.Clean dust from brake parts using brake
cleaning fluid.
WARNING: Do not use an air line to blow
dust from brake assembly. Do not use
petroleum based fluid as damage will occur
to rubber components.
6.Clean mating faces of calliper and hub.
7.Fit pad retainers to calliper bracket.
8.Fit brake pads to calliper carrier.
The leading edge of the pads have chamfers
on them, the chamfers are asymmetric. It is
imperative that the pads are correctly fitted.
Pad 'A' in illustration must be fitted to the
inboard side of the calliper. Pad 'B' must be
fitted to the outboard side of the calliper.
9.Position calliper housing to carrier, align flats
on guide pins with calliper housing.
10.Ensure flats on guide pins locate with lugs on
calliper housing. Fit bolts and tighten to 27 Nm
(20 lbf.ft).
11.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
12.Remove stands and lower vehicle.
Wheel cylinder - rear
$% 70.60.19
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Remove rear brake shoes.

+ BRAKES, REPAIRS, Brake Shoes -
rear set.
4.Disconnect pipe union from wheel cylinder.
CAUTION: Always fit plugs to open
connections to prevent contamination.
5.Remove 2 bolts securing wheel cylinder and
remove wheel cylinder.
6.Use a wire brush to remove any corrosion.
7.Clean backplate and drum with brake cleaning
fluid.
WARNING: Do not use an air line to blow
dust from brake assembly. Do not use
petroleum based fluid as damage will occur
to rubber components.
Refit
1.Fit wheel cylinder to backplate, fit bolts and
tighten to 8 Nm (6 lbf.ft).
2.Connect brake pipe union to wheel cylinder and
tighten union to 17 Nm (12 lbf.ft).
3.Fit brake shoes.

+ BRAKES, REPAIRS, Brake Shoes -
rear set.
4.Bleed brakes.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
5.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
6.Remove stands and lower vehicle.
M70 1148
AB

RESTRAINT SYSTEMS
REPAIRS 75-13
Air bag - steering wheel
$% 76.74.01
Remove
WARNING: It is imperative that before any
work is undertaken on the SRS system the
appropriate information is read thoroughly.
WARNING: When removing, testing or
installing an airbag module, do not lean
directly over it.
1.Make the SRS system safe.

+ GENERAL INFORMATION,
Supplementary restraint system
precautions.
2.Remove 2 Torx bolts securing airbag module to
steering wheel.
3.Release airbag module from steering wheel.
CAUTION: Do not allow the airbag module
to hang by the airbag harness.
4.Disconnect SRS connector from air bag
module.
5.Remove airbag module.
WARNING: Store the airbag module with the
deployment side uppermost. If it is stored
deployment side down, accidental
deployment will propel the airbag module
with enough force to cause serious injury.Refit
1.Position airbag module and fit connector with
harness pointing upwards.
NOTE: If the airbag module is to be replaced,
the bar code of the new module must be
recorded.
2.Fit airbag module to steering wheel and tighten
Torx bolts to 9 Nm (7 lbf.ft).
3.Connect battery leads, earth lead last.

DOORS
REPAIRS 76-1-5
Door - tail assembly - remove for access
& refit
$% 76.28.19.99
Remove
1.Remove spare wheel from taildoor.
2.Remove RH rear quarter lower trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
3.Release and disconnect 3 multiplugs and rear
washer tube from lower 'E' post.
4.Remove 2 bolts from tail door check strap,
release strap and position aside.5.Release door harness sheath from 'E' post and
pull harness through 'E' post.
6.Mark position of hinges.
7.Support weight of tail door.
8.Remove 6 bolts securing tail door hinges to
body and with assistance, remove tail door.
Refit
1.With assistance position door. Fit securing
bolts but do not tighten at this stage.
2.Position check strap and secure with bolts.
3.Align hinges and tighten bolts to 30 Nm (22
lbf.ft).
4.Feed door harness through 'E' post and secure
harness sheath.
5.Connect and secure multiplugs and rear
washer tube at 'E' post.
6.Fit rear quarter lower casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
7.Fit spare wheel to tail door.

EXTERIOR FITTINGS
REPAIRS 76-2-1
EXTERIOR FITTINGS REPAIRS
Wing - front
$% 76.10.24
Remove
1.Remove front mud flap.

+ EXTERIOR FITTINGS, REPAIRS,
Mud flap - front.
2.Remove lower sill finisher.

+ EXTERIOR FITTINGS, REPAIRS,
Finisher - sill - lower.
3.Remove 4 bolts securing rear of front wing.
4.Release wheel arch liner from rear of front
wing.5.Remove 2 bolts securing wing bracket to 'A'
post.
6.Remove 4 bolts securing top of wing.
7.Remove bolt securing front of wing to bracket
on body.
8.Remove screw securing wheelarch liner to
under side of wing.
9.Release wing from body and disconnect
multiplug from repeater lamp.
10.Remove front wing from body.
11.Remove side repeater lamp from front wing.

EXTERIOR FITTINGS
76-2-2 REPAIRS
Refit
1.Fit side repeater lamp to front wing.
2.Position front wing to body.
3.Connect repeater lamp multiplug.
4.Align front wing to body.
5.Fit bolts securing rear wing to 'A' post, top of
wing and front of wing, but do not tighten at this
stage.
6.Align wing and tighten bolts in sequence shown
to 5 Nm (3.5 lbf.ft).
7.Align wheel arch liner to rear of wing.
8.Fit screw securing wheel arch liner to under
side of wing.
9.Fit lower sill finisher.

+ EXTERIOR FITTINGS, REPAIRS,
Finisher - sill - lower.
10.Fit front mud flap.

+ EXTERIOR FITTINGS, REPAIRS,
Mud flap - front.
Liner - front wheel arch
$% 76.10.48
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Remove front mud flap.

+ EXTERIOR FITTINGS, REPAIRS,
Mud flap - front.
4.Remove 3 screws securing wheel arch liner to
wing and bumper.
5.Remove 8 retaining studs securing wheel arch
liner to inner wing.
6.Release and remove wheel arch liner.
Refit
1.Fit wheel arch liner.
2.Fit retaining studs securing wheel arch liner to
inner wing.
3.Fit and tighten screws securing wheel arch liner
to wing and bumper.
4.Fit front mud flap.

+ EXTERIOR FITTINGS, REPAIRS,
Mud flap - front.
5.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
6.Remove stand and lower vehicle.

EXTERIOR FITTINGS
76-2-4 REPAIRS
Panel - underbelly
$% 76.10.50
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove 2 screws securing bumper valance to
underbelly panel brackets.
3.Remove 4 screws securing wheel arch liners to
bumper valance, if fitted.
4.Remove 2 bolts securing rear of underbelly
panel.
5.Remove 6 bolts securing underbelly panel
frame.
6.Remove underbelly panel.
Refit
1.Position underbelly panel.
2.Fit bolts securing underbelly panel frame and
tighten to 45 Nm (33 lbf.ft).
3.Fit bolts securing rear of underbelly panel and
tighten to 8 Nm (6 lbf.ft).
4.Fit and tighten screws securing wheel arch
liners to bumper valance, if fitted.
5.Fit and tighten screws securing bumper
valance to brackets.
6.Remove stands and lower vehicle.
Mirror - exterior - electric
$% 76.10.57
Remove
1.Remove cheater panel.
2. Up to 04MY:Disconnect 2 Lucars from tweeter
and place cheater panel aside.From 04MY:
Disconnect multiplug from tweeter and position
cheater panel aside.
3.Disconnect multiplug from mirror.
4.Support mirror and remove 2 Torx screws.
From 04MY: Remove additional Torx screw.
5.
6.Remove exterior mirror.
7.Collect clamping plate.
Refit
1.Position mirror, locate clamping plate, fit and
tighten Torx screws to 6 Nm (4.5 lbf.ft).
2.Connect multiplug to mirror.
3. 04MY: Connect multiplug to tweeter.
4.Connect Lucars to tweeter in cheater panel.
5.Fit cheater panel to door.

EXTERIOR FITTINGS
76-2-6 REPAIRS
Bracket - spare wheel mounting
$% 76.11.18
Remove
1.Lower tail door glass.
2.Remove 3 screws securing high mounted stop
lamp bracket to spare wheel carrier.
3.Disconnect multiplug and remove lamp.
4.Remove 3 nuts securing spare wheel to
mounting bracket.
5.Remove spare wheel from mounting bracket.6.Remove 6 Torx bolts and 2 nuts securing spare
wheel mounting bracket to tail door.
7.Remove mounting bracket.
Refit
1.Position spare wheel mounting bracket to tail
door and tighten bolts to 13 Nm (10 lbf.ft).
2.Tighten mounting bracket nuts to 25 Nm (18
lbf.ft).
3.Position stop lamp and connect multiplug.
4.Fit stop lamp and secure with screws.
5.Fit spare wheel and tighten nuts to 45 Nm (33
lbf.ft).
6.Raise tail door glass.

EXTERIOR FITTINGS
76-2-10 REPAIRS
Bumper - assembly - front - up to 04MY
$% 76.22.72
Remove
1.Open bonnet.
2.Remove 8 screws securing wheel arch liners to
bumper, release liners from wheelarch for
access.
3.Remove 2 screws securing bumper valance to
underbelly panel brackets.
4.Remove 3 scrivets securing bumper to
armature.
5.Remove 2 bolts securing rear edge of front
bumper to inner front wing.
6.Remove 4 screws securing bumper to bonnet
locking platform.
7. NAS Models: Release side repeater,
disconnect multiplug and remove repeater.
8.With assistance carefully lift and pull forward
each side of bumper to release bumper side
mounts and clips.
CAUTION: Always protect paintwork when
removing or refitting any body trims or
bumpers.
9.Remove front number plate.
10.Remove badge from grill and discard clips.Refit
1.Fit badge to grill.
2.Fit number plate.
3.With assistance, fit bumper assembly to body.
4. NAS Models: Feed side repeater harness
through bumper, connect multiplug and fit
repeater.
5.Ensure bumper locating pegs are correctly
aligned.
6.Fit and tighten bolts securing bumper to wings.
7.Fit screws securing bumper to bonnet locking
platform.
8.Fit scrivets to armature.
9.Fit screws securing bumper to underbelly
panel.
10.Fit and align wheelarch liners and tighten
screws.
11.Close bonnet.

EXTERIOR FITTINGS
REPAIRS 76-2-11
Bumper - assembly - front - from 04MY
$% 76.22.72
Remove
1.Open bonnet.
2.Remove 8 screws securing wheel arch liners to
bumper, release liners from wheel arch for
access.
3.Remove 4 screws securing bumper valance to
underbelly panel.
4.Remove 3 scrivets securing bumper to
armature.5.Disconnect multiplugs from fog/driving lamps.
6.Remove 2 bolts securing rear edge of front
bumper to inner front wing.
7.Remove 4 screws securing bumper to bonnet
locking platform.
M76 4674