width LAND ROVER FREELANDER 2001 Workshop Manual

INTRODUCTION
01-4
HRW Heated Rear Window
ht/HT High tension
HSLA High Strength Low Alloy
IACV Idle Air Control Valve
IAT Intake Air Temperature
ICE In-Car Entertainment
i.dia. Internal diameter
IDM Intelligent Driver Module
IF Intermediate Frequency
in Inch
in
2Square inch
in3Cubic inch
ILT Inlet Throttle
ISO International Organisation for
Standardisation
ITS Inflatable Tubular Structure
k Thousand
kg Kilogramme
kg/h Kilogrammes per hour
km Kilometre
km/h Kilometres per hour
kPa KiloPascal
KS Knock Sensor
lLitre
lb(s) Pounds
lbf Pounds force
lbf.in Pounds force inches
lbf/in
2Pounds per square inch
lbf.ft Pounds force feet
λLambda
lc Low compression
LCD Liquid Crystal Display
LED Light Emitting Diode
LEV Low Emission Vehicle
LH Left-Hand
LHD Left-Hand Drive
LSM Light Switch Module
LVS Liquid Vapour Separator
mMetre
µMicro
MAF Mass Air Flow
MAP Manifold Absolute Pressure
MFU Multi-Function Unit
MFL Multi-Function Logic
max. Maximum
MEMS Modular Engine Management
System
MIG Metal/Inert Gas
MIL Malfunction Indicator Lamp
MPa MegaPascal
MOSFET Metal Oxide Semiconductor Field
Effect Transistor
min. Minimum
- Minus (tolerance)
' Minute (angle)
mm Millimetre
mph Miles per hour MPi Multi-Point injection
MV Motorised Valve
MY Model Year
NAS North American Specification
(-) Negative (electrical)
Nm Newton metre
No. Number
NO
2Nitrogen Dioxide
NO
xOxides of Nitrogen
NTC Negative Temperature
Coefficient
NRV Non Return Valve
OBD On Board Diagnostics
OBM On Board Monitoring
o.dia. Outside diameter
OAT Organic Acid Technology
ORM Off-road Mode
ΩOhm
PAS Power Assisted Steering
PCB Printed Circuit Board
PCV Positive Crankcase Ventilation
PDC Parking Distance Control
PDOP Position Dilation Of Precision
PI Programme Information
PPS Pulse Per Second
PS Programme Service
psi Pounds per square inch
pts. Pints
% Percentage
+ Plus (tolerance) or Positive
(electrical)
±Plus or minus (tolerance)
PTC Positive Temperature Coefficient
PTFE Polytetrafluorethylene
PWM Pulse Width Modulation
RDS Radio Data Service
rRadius
:Ratio
ref Reference
REG Regionalisation
RES Rover Engineering Standards
rev/min Revolutions per minute
RF Radio Frequency
RGB Red / Green / Blue
RH Right-Hand
RHD Right-Hand Drive
ROM Read Only Memory
RON Research Octane Number
ROV Roll Over Valve
ROW Rest Of World
SAE Society of Automotive Engineers
SAI Secondary Air Injection
" Second (angle)
SLABS Self Levelling and Anti-Lock
Brake System
SLS Self Levelling Suspension
SOHC Single Overhead Camshaft
SPE Single Point Entry

GENERAL DATA
04-1
GENERAL DATA
Engine - Td4 Diesel
General
Type 2.0 litre in-line direct injection diesel, 16-valve, DOHC, turbocharged
and intercooled
Cylinder arrangement 4 in-line, transverse, No.1 cylinder at front of engine
Bore 84.00 mm (3.307 in.)
Stroke 88.00 mm (3.465 in.)
Capacity 1951 cm
3 (119.05 in3)
Firing order 1-3-4-2
Compression ratio 18:1 ± 0.5:1
Direction of rotation Clockwise, viewed from the front of the engine
Maximum power:
⇒ Up to 03 Model Year - Manual and automatic
gearbox
⇒ 03 Model Year onwards - Manual gearbox
⇒ 03 Model Year onwards - Automatic gearbox82 kW (112 bhp) @ 4000 rev/min.
82 kW (112 bhp) @ 4000 rev/min
80 kW (107 bhp) @ 4000 rev/min
Maximum torque 260 Nm (192 lbf.ft) @ 1750 rev/min.
Maximum governed speed 4800 rev/min.
Maximum overrun speed 5250 rev/min
Idle speed 780 ± 30 rev/min
Dimensions:
⇒ Length
⇒ Width
⇒ Height482 mm (19.0 in)
634 mm (25.0 in)
697 mm (27.4 in)
Glow plugs: 4 off, one per cylinder arranged centrally on inlet side between inlet
valves
Turbocharger Garrett GT2
Fuel injection system: Common rail, direct injection fed by Bosch high pressure delivery
pump
Injection timing Controlled by ECM
Emissions standard ECD3
Valve timing
Inlet valves:
⇒ Opens
⇒ Closes8° BTDC
28° ABDC
Exhaust valves:
⇒ Opens
⇒ Closes38° BBDC
4° ATDC

GENERAL DATA
04-5
Valves
Stem diameter:
⇒ Inlet 5.97 ± 0.01 mm (0.235 ± 0.0004 in.)
⇒ Exhaust 5.97 ± 0.01 mm (0.235 ± 0.0004 in.)
Valve stem to guide clearance 0.025 - 0.054 mm (0.0010 - 0.0021 in.)
Valve head stand down:
⇒ Inlet 0.73 ± 0.1 mm (0.029 ± 0.004 in.)
⇒ Exhaust 0.56 ± 0.1 mm (0.022 ± 0.004 in.)
Head diameter 25.9 ± 0.1 mm (1.02 ± 0.004 in.)
Valve seat angle: 45°
Valve seat width:
⇒ Inlet 1.20 ± 0.15 mm (0.047 ± 0.006 in)
⇒ Exhaust 1.45 ± 0.15 mm (0.057 ± 0.006 in)
Valve springs
Type Parallel, single coil
Free length 47.5 mm (1.87 in.)
Fitted length 32 mm (1.26 in.)

GENERAL DATA
04-6
Engine - K1.8 Petrol
General
Type 1.8 litre petrol, 16-valve DOHC
Cylinder arrangement 4 in-line, transverse, No.1 cylinder at front of engine
Bore 80.00 mm (3.150 in.)
Stroke 89.30 mm (3.516 in.)
Capacity 1796 cm
3 (109.59 in3)
Firing order 1-3-4-2
Compression ratio 10.5 :1 ± 0.5 :1
Direction of rotation Clockwise viewed from the front of the engine
Maximum power 88 kW (118 bhp) @ 5500 rev/min.
Maximum torque 165 Nm (223.7 lbf.ft) @ 2750 rev/min.
Idle speed 775 ± 50 rev/min.
Maximum intermittent engine speed 6750 rev/min.
Weight (fully dressed, wet) 108 kg (238 lb)
Dimensions:
⇒ Length (nominal) 654 mm (25.75 in.)
⇒ Width (nominal) 600 mm (23.62 in.)
⇒ Height (nominal) 615 mm (24.21 in.)
Spark plugs:
⇒ Type NLP 100290
⇒ Gap 1.0 mm ± 0.05 mm (0.039 in. ± 0.002 in.)
Ignition coils:
⇒ Make Nippon Denso - NEC 100730
⇒ Type 2 x twin output coils, plug top mounted; cylinders 1 & 4 and 2 & 3
⇒ Primary resistance (typical) 0.7 Ω
⇒ Secondary resistance (typical) 10 Ω
Fuel injection system:
Type Returnless fuel rail, multi-point fuel injection, electronically controlled
from ECM
Controller MEMS 3 breakerless, electronic, fully mapped engine management
system
Injectors:
⇒ Operating pressure 3.5 bar (50.8 lbf.in
2)
⇒ Fuel flow rate 117 g/min. @ 3.0 bar (4.13 fl.oz/min. @ 43.5 lbf. in
2)
Valve operation Self-adjusting, lightweight hydraulic tappets operated directly by
camshafts
Emissions standard ECD3
Cylinder block:
Material Aluminium alloy
Cylinder liner type Damp, bottom half stepped - sliding fit into lower part of cylinder block
Cylinder liner bore:
⇒ RED grade A 80.000 - 80.015 mm (3.1496 - 3.1501 in.)
⇒ BLUE grade B 80.016 - 80.030 mm (3.1502 - 3.1508 in.)

GENERAL DATA
04-8
Pistons
Type Aluminium alloy, tin plated, thermal expansion with offset gudgeon pin
Piston diameter:
⇒ Grade A 79.975 - 79.990 mm (3.1486 - 3.1492 in.)
⇒ Grade B 79.991 - 80.005 mm (3.1492 - 3.1498 in.)
Clearance in bore 0.01 - 0.04 mm (0.0004 - 0.0016 in.)
Maximum ovality 0.30 mm (0.012 in.)
Piston rings:
Type: 2 compression, 1 oil control
⇒ Top compression ring Barrel faced, granulite coated
⇒ 2nd compression ring Tapered, phosphate coated
⇒ Oil control ring Nitrided ring with radii and spring
New ring to groove clearance:
⇒ Top compression ring 0.040 - 0.072 mm (0.0016 - 0.0028 in.)
⇒ 2nd compression ring 0.030 - 0.062 mm (0.0012 - 0.0024 in.)
⇒ Oil control ring 0.010 - 0.180 mm (0.0004 - 0.0071 in.)
Ring fitted gap 20 mm (0.75 in) from top of bore:
⇒ Top compression ring 0.20 - 0.35 mm (0.008 - 0.014 in.)
⇒ 2nd compression ring 0.28 - 0.48 mm (0.011 - 0.019 in.)
⇒ Oil control ring 0.15 - 0.40 mm (0.006 - 0.016 in.)
Piston ring width:
⇒ Top compression ring 0.978 - 0.990 mm (0.0385 - 0.0390 in.)
⇒ 2nd compression ring 1.178 - 1.190 mm (0.0464 - 0.0469 in.)
⇒ Oil control ring 0.33 - 0.38 mm (0.0130 - 0.0150 in.)
Camshaft
Type DOHC acting directly on tappets, incorporates target/reluctor for
camshaft sensor
Bearings 6 per camshaft, direct line bored
Drive Toothed belt driven from crankshaft gear, automatically tensioned
Camshaft end-float 0.06 - 0.19 mm (0.002 - 0.007 in.)
⇒ Service limit 0.30 mm (0.012 in.)
Bearing clearance 0.060 - 0.094 mm (0.0024 - 0.0037 in.)
⇒ Service limit 0.15 mm (0.006 in.)
Tappets
Type Self-adjusting lightweight hydraulic tappets, operated directly from
camshafts
Tappet outside diameter 32.959 - 32.975 mm (1.2976 - 1.2982 in.)
Valve timing:
Inlet valves:
⇒ Opens
⇒ Closes
⇒ Maximum lift12° BTDC
52° ABDC
8.8 mm (0.35 in.)
Exhaust valves:
⇒ Opens
⇒ Closes
⇒ Maximum lift52° BBDC
12° ATDC
8.8 mm (0.35 in.) General

GENERAL DATA
04-9
Valves
Stem diameter:
⇒ Inlet valves 5.952 - 5.967 mm (0.2343 - 0.2349 in.)
⇒ Exhaust valves 5.947 - 5.962 mm (0.2341 - 0.2347 in.)
Stem to guide clearance:
⇒ Inlet valves 0.033 - 0.063 mm (0.0013 - 0.0025 in.)
⇒⇒ Service limit 0.07 mm (0.0028 in.)
⇒ Exhaust valves 0.038 - 0.078 mm (0.0015 - 0.0031 in.)
⇒⇒ Service limit 0.11 mm (0.0043 in.)
Valve stem fitted height:
⇒ New 38.93 - 39.84 mm (1.5327 - 1.5685 in.)
⇒ Service limit 40.10 mm (1.5787 in.)
Head diameter:
⇒ Inlet valves 27.6 - 27.8 mm (1.087 - 1.094 in.)
⇒ Exhaust valves 24.0 - 24.2 mm (0.945 - 0.953 in.)
Valve seat width:
⇒ Inlet 1.0 - 1.4 mm (0.039 - 0.055 in)
⇒ Exhaust 1.4 - 1.8 mm (0.055 - 0.071 in)
Seat face angle - Inlet and Exhaust 45°
Valve face angle - Inlet and Exhaust 45°
Valve springs
Free length 50.0 mm (1.97 in.)
Fitted length 37.0 mm (1.46 in.)
Load at fitted length 250 ± 12 N
Load at valve open length 450 ± 18 N
Lubrication
Type Cast aluminium wet sump
Pump type Crankshaft driven, eccentric rotor
⇒ Outer rotor to housing clearance 0.28 - 0.36 mm (0.011 - 0.014 in.)
⇒ Inner rotor tip clearance 0.05 - 0.13 mm (0.002 - 0.005 in.)
⇒ Rotor end-float 0.02 - 0.06 mm (0.001 - 0.002 in.)
Relief valve spring free length 38.90 mm (1.531 in.)
Oil filter Full flow disposable screw-on canister
Pressure at idle (min.)
Pressure at 2500 rev/min (hot)
Relief valve opening pressure
Low oil pressure switch opening pressure100 kPa (14.5 lbf/in
2)
375 kPa (3.75 bar, 54.4 lbf/in2)
410 kPa (59.5 lbf/in2)
20 - 58 kPa (3.0 - 8.5 lbf/in2) General

GENERAL DATA
04-11
Engine - KV6 Petrol
General
Type:
⇒ Up to 03 Model Year
⇒ From 03 Model Year2.5 litre V6, 24 valve, air assisted direct fuel injection petrol, water
cooled, transverse mounted
2.5 litre V6, 24 valve, direct fuel injection petrol, water cooled,
transverse mounted
Cylinder arrangement: 90° V6, numbered from the front of the engine
⇒ Left bank Cylinders 1, 3 and 5
⇒ Right bank Cylinders 2, 4 and 6
Bore (nominal) 80 mm (3.15 in.)
Stroke 82.8 mm (3.26 in.)
Capacity 2497 cm
3 (152.37 in3)
Firing order 1-6-5-4-3-2
Compression ratio 10.5 : 1 ± 0.5 : 1
Direction of rotation Clockwise viewed from front of engine
Maximum power 130 kW (177 bhp) @ 6500 rev/min.
Maximum torque 240.0 Nm (177 lbf.ft) @ 4000 rev/min.
Maximum engine speed:
⇒ Continuous 6500 rev/min.
⇒ Intermittent 6750 rev/min.
Idle speed 750 rev/min. ± 50 rev/min.
Weight (fully dressed, wet) 154 kg (340 lb)
Dimensions (dressed):
⇒ Length (nominal) 770 mm (30.3 in.)
⇒ Width (nominal) 750 mm (29.5 in.)
⇒ Height (nominal) 750 mm (29.5 in.)
Valve operation Self-adjusting lightweight hydraulic tappets operated directly by the
camshafts
Fuel injection system:
⇒ Make - Up to 03 Model Year
⇒ Make - From 03 Model YearSiemens engine management system
Siemens engine management system
⇒ Type - Up to 03 Model Year
⇒ Type - From 03 Model YearMulti-point, air assisted fuel injection controlled by ECM, electro-
mechanical injectors with twin sprays targeted on to back of inlet
valves
Multi-point fuel injection controlled by ECM, electro-mechanical
injectors with quadruple sprays targeted on to back of inlet valves
Inlet manifold Variable geometry
Spark plugs
⇒ Type
⇒ Plug gapNLP 100290
1.0 mm ± 0.05 mm (0.039 in. ± 0.002 in.)
Coils:
⇒ Make - Up to 03 Model Year
⇒ Make - From 03 Model Year
⇒ Type - Up to 03 Model Year
⇒ Type - From 03 Model YearBREMR
Champion BAE 403H
6 x coils (3 x plug top, 3 x remote mounted)
6 x coils (6 x plug top)
Emissions standard ECD3

GENERAL DATA
04-14
Clearance in bore 20 mm (0.75 in.) from bottom of
cylinder bore0.034 - 0.035 mm (0.0013 - 0.0014 in.)
Maximum ovality 0.3 mm (0.012 in.)
Piston rings
Type:
⇒ Top compression ring Chrome plated steel
⇒ 2nd compression ring Chrome plated cast iron
⇒ Oil control ring Stainless steel top and bottom rails with expander ring
New ring to groove clearance:
⇒ Top compression ring 0.05 - 0.08 mm (0.0020 - 0.0031 in.)
⇒ 2nd compression ring 0.04 - 0.07 mm (0.0012 - 0.0024 in.)
⇒ Oil control ring 0.010 - 0.180 mm (0.0004 - 0.0071 in.)
Ring fitted gap 20 mm (0.75 in) from top of bore:
⇒ Top compression ring 0.20 - 0.35 mm (0.008 - 0.014 in.)
⇒ 2nd compression ring 0.28 - 0.45 mm (0.011 - 0.018 in.)
⇒ Oil control ring 0.25 - 1.00 mm (0.010 - 0.039 in.)
Piston ring width:
⇒ Top compression ring 3.1 ± 0.15 mm (0.122 ± 0.006 in.)
⇒ 2nd compression ring 3.15 - 3.45 mm (0.124 - 0.136 in.)
⇒ Oil control ring 2.286 - 2.438 mm (0.090 - 0.096 in.)
Camshaft
Type Twin camshafts on each cylinder bank retained by camshaft carrier,
line bored with cylinder head. Reluctor for camshaft sensor mounted
on left hand inlet camshaft
Camshaft identification:
⇒ Inlet Orange paint mark
⇒ Exhaust Blue paint mark
Bearings 5 per camshaft
Drive Toothed belt driven from crankshaft to front of inlet camshafts, 2 x
short toothed belts from rear of inlet camshafts to exhaust camshafts
Camshaft end-float 0.06 - 0.19 mm (0.002 - 0.007 in.)
⇒ Service limit 0.3 mm (0.012 in.)
Bearing clearance 0.025 - 0.059 mm (0.0010 - 0.0023 in.)
⇒ Service limit 0.1 mm (0.004 in.)
Tappets
Type Hydraulic self-adjusting, directly operated from camshafts
Tappet outside diameter 32.959 - 32.975 mm (1.2976 - 1.2982 in.)
Valve timing
Inlet valves:
⇒ Opens
⇒ Closes2° BTDC
54° ABDC
Exhaust valves:
⇒ Opens
⇒ Closes50° BBDC
14° ATDC
Valve maximum lift:
Inlet valves 8.2 mm (0.32 in.)
Exhaust valves 8.8 mm (0.35 in.) General

GENERAL DATA
04-15
* New metal dowels supplied with gasket must be fitted
Valves
Stem diameter:
⇒ Inlet valves 5.952 - 5.967 mm (0.2343 - 0.2349 in.)
⇒ Exhaust valves 5.947 - 5.962 mm (0.2341 - 0.2347 in.)
Stem to guide clearance:
Inlet valves 0.033 - 0.063 mm (0.0013 - 0.0025 in.)
⇒ Service limit 0.07 mm (0.0028 in.)
Exhaust valves 0.038 - 0.078 mm (0.0015 - 0.0013 in.)
⇒ Service limit 0.11 mm (0.0043 in.)
Valve stem fitted height:
⇒ New 38.93 - 39.84 mm (1.533 - 1.569 in.)
⇒ Service limit 40.10 mm (1.579 in.)
Valve guide fitted height 6.0 mm (0.24 in.)
Valve guide inside diameter 6.000 - 6.025 mm (0.2362 - 0.2372 in.)
Head diameter:
⇒ Inlet valves 31.4 - 31.6 mm (1.236 - 1.244 in.)
⇒ Exhaust valves 27.3 - 27.5 mm (1.075 - 1.083 in.)
Valve seat width:
⇒ Inlet valves
⇒ Exhaust valves1.2 mm (0.05 in.)
1.6 mm (0.06 in)
Seat face angle:
⇒ Inlet valves
⇒ Exhaust valves45°
45°
Valve face angle:
⇒ Inlet valves
⇒ Exhaust valves45°
45°
Valve springs
Free length 47.6 mm (1.874 in.)
Fitted length 37.0 mm (1.457 in.)
Load at fitted length 210 ± 13 N
Load at top of lift 440 ± 22 N
Lubrication
Type Cast aluminium, wet sump with full flow filtration
Oil pump: Crankshaft driven, high pressure die cast body
⇒ Outer rotor end-float 0.04 - 0.09 mm (0.0016 - 0.0035 in.)
⇒ Inner rotor end-float 0.04 - 0.09 mm (0.0016 - 0.0035 in.)
⇒ Inner rotor tip 0.05 - 0.13 mm (0.002 - 0.005 in)
⇒ Outer rotor to body diameterical clearance
0.13 - 0.23 mm (0.0051 - 0.0091 in.)
⇒ Rotor body to drive gear clearance (pump not fitted)
0.15 - 0.25 mm (0.0059 - 0.0098 in.)
Relief valve spring free length 38.90 mm (1.531 in)
Oil filter Full-flow disposable cartridge
Oil cooler Partial flow type
Pressure at idle (min.) 1.0 bar (14.5 lbf.in
2)
Pressure at 3000 rev/min. 3.0 bar (43.5 lbf.in
2)
Relief valve opening pressure 4.1 bar (59.5 lbf.in
2)
Low oil pressure switch opening pressure 0.3 - 0.5 bar (4.4 - 7.3 lbf.in
2) General

GENERAL DATA
04-22
Manual Gearbox - PG1
Gear ratios:
⇒ First 3.250 : 1 (19.902 : 1 overall)
⇒ Second 1.894 : 1 (11.598 : 1 overall)
⇒ Third 1.222 : 1 (7.483 : 1 overall)
⇒ Fourth 0.848 : 1 (5.019 : 1 overall)
⇒ Fifth 0.649 : 1 (3.974 : 1 overall)
⇒ Reverse 3.000 : 1
Reverse idler gear to selector fork clearance 0.5 to 1.1 mm (0.020 - 0.043 in)
Selector fork prong width 13.0 to 13.3 mm (0.512 - 0.524 in)
Selector fork groove to pin clearance:
⇒ Standard 0.05 to 0.35 mm (0.002 - 0.014 in)
⇒ Service limit 0.50 mm (0.020 in)
Selector fork groove width 7.05 to 7.25 mm (0.278 - 0.285 in)
Gearshift arm to guide clearance:
⇒ Standard 0.20 to 0.30 mm (0.008 - 0.012 in)
⇒ Service limit 0.55 mm (0.022 in)
Interlock shift guide groove width 8.10 to 8.20 mm (0.319 - 0.323 in)
Synchro ring to gear clearance:
⇒ Standard 0.85 to 1.10 mm (0.033 - 0.043 in)
⇒ Service limit (minimum clearance) 0.40 mm (0.016 in)
Selector shaft forks in synchro sleeve grooves
clearance:
⇒ Standard 0.45 to 0.65 mm (0.018 - 0.026 in)
⇒ Service limit 1.00 mm (0.039 in)
Gearshift arm guide to selector fork clearance:
⇒ Standard 0.20 to 0.50 mm (0.008 - 0.020 in)
⇒ Service limit 0.80 mm (0.031 in)
Gearshift arm guide tongue width 11.90 to 12.00 mm (0.469 - 0.472 in)
Gearshift arm guide to interlock assembly clearance:
⇒ Standard 0.05 to 0.35 mm (0.002 - 0.014 in)
⇒ Service limit 0.60 mm (0.024 in)
Gearshift arm guide groove width 13.05 to 13.25 mm (0.514 - 0.522 in)
Interlock ball to gearshift arm guide clearance:
⇒ Standard 0.05 to 0.25 mm (0.002 - 0.010 in)
⇒ Service limit 0.50 mm (0.020 in)
Interlock ball outside diameter 12.05 to 12.15 mm (0.474 - 0.478 in)
2nd to 3rd gear clearance:
⇒ Standard 0.06 to 0.21 mm (0.002 - 0.008 in)
⇒ Service limit 0.30 mm (0.012 in)
3rd gear thickness:
⇒ Standard 35.42 to 35.47 mm (1.394 - 1.396 in)
⇒ Service limit 35.30 mm (1.390 in)