turn signal LAND ROVER FRELANDER 2 2006 User Guide

Publi s hed: 11-May-2011
Exterior Lighting - Side Turn Signal Lamp
Removal and Inst all ati on
Removal 1.
Installation To i nst all , revers e t he removal procedure.
1.

DT C
Description Possible Cause Action
B117E72 Front Power W i ndow
up Act uator s tuck open Cl ear DTC and re-tes t. If DTC returns , ins t al l a new
DDM/PDM, refer to the new modul e i ns t allat ion not e
at t he t op of the DTC Index
B117E73 Front Power W i ndow
up Act uator s tuck clos ed Cl ear DTC and re-tes t. If DTC returns , ins t al l a new
DDM/PDM, refer to the new modul e i ns t allat ion not e
at t he t op of the DTC Index
B117F72 Front Power W i ndow
down Act uator s tuck open Cl ear DTC and re-tes t. If DTC returns , ins t al l a new
DDM/PDM, refer to the new modul e i ns t allat ion not e
at t he t op of the DTC Index
B117F73 Front Power W i ndow
down Act uator s tuck clos ed Cl ear DTC and re-tes t. If DTC returns , ins t al l a new
DDM/PDM, refer to the new modul e i ns t allat ion not e
at t he t op of the DTC Index
B118929 Front W indow
Pos it ion Sens or Signal i nval id Carry out pinpoint t est s as s oci at ed wi th this DTC
us ing the manufact urer approved di agnos t ic s yst em
B118A29 Rear W i ndow
Pos it ion Sens or Signal i nval id Carry out pinpoint t est s as s oci at ed wi th this DTC
us ing the manufact urer approved di agnos t ic s yst em
B11D183 LIN Bus Ci rcuit "C" Value of s ignal protecti on
cal cul at ion incorrect Refer to t he elect rical circuit di agrams and t est LIN
ci rcuit between driver swit ch pack and DDM for
s hort /open circui ts , clear DTC and re-t est . If DTC
remains i nst all a new swit ch pack.
REFER t o: Dri ver Door W i ndow Cont rol Swi tch (501-11 Gl ass , Frames and Mechanis ms , Removal
and Ins tall ati on).
B11D186 LIN Bus Ci rcuit "C" Signal Inval id Refer to t he elect rical circuit di agrams and t est LIN
ci rcuit between driver swit ch pack and DDM for
s hort /open circui ts , clear DTC and re-t est . If DTC
remains i nst all a new swit ch pack.
REFER t o: Dri ver Door W i ndow Cont rol Swi tch (501-11 Gl ass , Frames and Mechanis ms , Removal
and Ins tall ati on).
B11D187 LIN Bus Ci rcuit "C" Mis s ing Mes s age Refer to t he elect rical circuit di agrams and t est LIN
ci rcuit between driver swit ch pack and DDM for
s hort /open circui ts , clear DTC and re-t est . If DTC
remains i nst all a new swit ch pack.
REFER t o: Dri ver Door W i ndow Cont rol Swi tch (501-11 Gl ass , Frames and Mechanis ms , Removal
and Ins tall ati on).
B11F611 Driver Fol ding Mi rror
Mot or Short To Ground Refer to el ect ri cal circui t diagrams and check driver
folding mirror mot or for s hort t o ground
B11F615 Driver Fol ding Mi rror
Mot or Short to power or open Refer to el ect ri cal circui t diagrams and check driver
folding mirror mot or for s hort t o power, open ci rcuit
B11F711 Pas s enger Fol ding
Mi rror Motor Short To Ground Refer to el ect ri cal circui t diagrams and check
pas s enger fol ding mi rror motor for s hort t o ground
B11F715 Pas s enger Fol ding
Mi rror Motor Short to power or open Refer to el ect ri cal circui t diagrams and check
pas s enger fol ding mi rror motor for s hort t o power,
open circui t
B1A9411 Driver Mirror Short to ground Refer to t he elect rical circuit di agrams and t est
driver mirror fold mot or circuit for s hort to ground
B1A9415 Driver Mirror Short to power or open circui t Refer to t he elect rical circuit di agrams and t est
driver mirror fold mot or circuit for s hort to power or
open circui t
B1A9511 Pas s enger Mirror Short to ground Refer to t he elect rical circuit di agrams and t est
pas s enger mi rror fold motor circui t for s hort t o
ground
B1A9515 Pas s enger Mirror Short to power or open circui t Refer to t he elect rical circuit di agrams and t est
pas s enger mi rror fold motor circui t for s hort t o power
or open circui t
B1A9883 LIN Bus Ci rcuit #1 Value of s ignal protecti on
cal cul at ion incorrect Carry out t he pinpoint t es t as s oci at ed wi th this DTC
us ing the manufact urer approved di agnos t ic s yst em.
Refer to t he elect rical circuit di agrams and t est LIN
ci rcuit between driver si de rear door modul e and
DDM for s hort /open circui ts , clear DTC and re-t es t . If
DTC remai ns ins tall a new s wit ch pack.
REFER t o: Dri ver Door W i ndow Cont rol Swi tch (501-11 Gl ass , Frames and Mechanis ms , Removal
and Ins tall ati on).
B1A9886 LIN Bus Ci rcuit #1 Signal Inval id Refer to t he elect rical circuit di agrams and t est LIN
ci rcuit between driver si de rear door modul e and
DDM for s hort /open circui ts , clear DTC and re-t es t . If
DTC remai ns ins tall a new s wit ch pack.
REFER t o: Dri ver Door W i ndow Cont rol Swi tch (501-11 Gl ass , Frames and Mechanis ms , Removal
and Ins tall ati on).
B1A9887 LIN Bus Ci rcuit #1 Mis s ing Mes s age Refer to t he elect rical circuit di agrams and t est LIN
ci rcuit between driver si de rear door modul e and
DDM for s hort /open circui ts , clear DTC and re-t es t . If
DTC remai ns ins tall a new s wit ch pack.
REFER t o: Dri ver Door W i ndow Cont rol Swi tch (501-11 Gl ass , Frames and Mechanis ms , Removal
and Ins tall ati on).

12-BJB
PRINCIPLES OF OPERATION
The wiper and was her s ys tem can operate i n a number of different ways when t he vehi cle i s in power mode 4 through 8.Reques t s from t he RH st eering col umn mult i-functi on s wit ch are trans mi tt ed over t he LIN bus t o the CJB, which i s t he maincont rol ler for t he s ys t em.
Windshield Wiper Slow Wipe
On recei vi ng a reques t for s low winds hield wiper operati on the CJB will energi ze relay 11 in t he BJB. W hen energized, relay11 provides a feed t o t he s wit ch cont act s of rel ay 8, whi ch is al so located i n t he CJB. Relay 8 is t he fast /s l ow wi pe relay.W hen s l ow wipe has been reques t ed relay 8 remai ns de-energized, allowi ng a feed to fl ow acros s the relay s wi tch contactst o the winds hi eld wi per motor s low speed brus h contacts .
Windshield Wiper Fast Wipe
On recei vi ng a reques t for fast windshi el d wi per operat ion t he CJB wi ll energize relay 11 and relay 8 i n t he BJB. W henenergized, relay 11 provides a feed to the s wi tch contacts of relay 8. The energized rel ay 8 provi des a feed t o t hewinds hield wiper mot or fast speed brus h contacts .
Windshield Wiper Intermittent Wipe
On recei vi ng a reques t for i ntermit tent wi nds hield wiper operati on, t he CJB wi ll energize relay 11 i n t he BJB to operat e t hewipers at s low s peed. Software cont ained wi thin the CJB i nterprets the t ime delay reques ted and controls operat ion ofrel ay 11 accordi ngl y.
The int ermi tt ent wiper s et t ing broadcast on the LIN bus t o t he CJB equat es to the followi ng t ime del ays .
LIN Bus SignalT ime Delay (seconds)
122
215.539.5
46
53.561
In the event of a LIN bus fai lure bet ween t he CJB and the RH s teeri ng col umn mul ti -funct ion s wi tch, the CJB wi ll default to'Limp Home' mode (see bel ow).
Windshield Wiper Automatic Wipe
On recei vi ng a reques t for aut omat ic winds hi eld wi per operat ion, t he CJB int erpret s LIN bus mess ages received from therai n s ens or. The rain sens or provides LIN bus mess ages wit h values rangi ng from 0 to 7. A s ignal val ue of 0 is interpretedby t he CJB as there being no wat er on the windshi eld.
A s i gnal value from 1 t o 5 i s int erpret ed by t he CJB as there being a smal l amount of wat er hi tt ing the wi nds hiel d. In t hisins t ance, the CJB i nit iates a s low wipe rout ine as det ailed in t he 'W inds hield W iper Slow W i pe' s ect ion above.
A s i gnal value from 6 t o 7 i s int erpret ed by t he CJB as there being a large amount of water hi tt ing t he wi nds hield. In t hisins t ance, the CJB i nit iates a fas t wi pe routi ne as detai led i n t he 'W i ndshi el d W iper Fas t W i pe' s ecti on above.
Rain s ens or s ens it ivit y can be adjus ted by turni ng t he rot ary control on the RH st eeri ng col umn mul ti -funct ion s wit ch t ot he required pos i ti on. Si x different s ensi ti vi ty set ti ngs are avail abl e, which are broadcas t over t he LIN bus to the CJB.
• NOTE: The CJB wil l onl y change a fas t wipe routi ne t o a s low wipe routi ne if t he rai n s ens or value i s lower t han 4.
Windshield Wiper Flick Wipe
On recei vi ng a reques t for fli ck wipe operat ion t he CJB wil l operate t he wi nds hiel d wipers as described in the 'Slow W ipe's ect ion above unti l the reques t is removed.
Windshield Wiper Park
The winds hield wiper park s wi tch i s int egral wit h t he winds hi eld wiper motor. The park s wit ch ensures the windshi el dwipers ret urn t o t he park pos it ion if t he winds hi eld wiper reques t i s cancell ed mid-s troke.
The CJB is connect ed t o one s ide of t he park s wit ch. The park s wit ch cont act s are open when the wi pers are in any pos it ionexcept t he park pos it ion. W hil e t he s wit ch cont act s are open, the CJB conti nues to energi ze rel ays 11 and 8 in the BJB,even if a LIN bus s ignal has been recei ved from t he RH s t eering column mult i-functi on s wit ch request ed t he wipers ares topped.
W hen t he wi pers reach t he park pos it ion, the park s wit ch cont act s clos e and a ground pat h i s created. W hen t he CJBregi st ers t his ground pat h i ts software logic det ermi nes the wipers are i n the park posi ti on and de-energi zes relays 11 and8 i n t he BJB.
Windshield Wiper Limp Home Mode
In the event of a LIN bus fai lure bet ween t he CJB and the RH s teeri ng col umn mul ti -funct ion s wi tch when t he wi nds hieldwipers are act ive, the CJB wi ll enter l imp home mode. In limp home mode, t he CJB will onl y power t he wi nds hiel d wipersat s low s peed.
Windshield Wiper Service Position
The winds hield wipers can be parked on the winds hi eld t o ai d the fi tment of new wi per bl ades . For more i nformati on, refer

61
Supplementary restraints system
R
Airbag deployment effectsAIRBAG WARNING LAMP
The airbag warning indicator is
mounted in the instrument pack,
and will illuminate as a bulb check
when the ignition is turned on.
If any of the following warning indicator
conditions occur, the vehicle should be
checked by your Land Ro ver Dealer/Authorised
repairer immediately.
• The warning indicator fails to illuminate
when the ignition is turned on.
• The warning indicator fails to extinguish
within six seconds of the ignition being
turned on.
• The warning indicator illuminates at any
time other than the bulb check, when the
ignition is turned on.WARNINGS
When an airbag inflates a fine powder
is released. This is normal, and not an
indication of a malf unction. However,
the powder may cause irritation to the skin,
and should be throughly flushed from eyes,
and any cuts or abrasions.
After inflation some airbag
components are at high temperatures.
To prevent injury, do no touch the
airbag components until they have cooled.
In order to react with sufficient speed,
airbags are deployed by an explosive
charge. Consequently airbag
deployment is accompan ied by a very loud
noise which may cause discomfort and
temporary loss of hearing.
WARNING
If the warning indicator signals that a
fault is present in the system, do not
use a child restraint on the front
passenger seat. Doing so will increase the risk
of death or serious injury to the child.

Digital audio broadcasting
238
L
Press and hold an ensemble search button to
display a list of all available ensembles. Rotate
the menu control to scroll through the
ensemble list and press it to select one and
display a list of channels in that ensemble.
Scanning channels
You can use the scan function to listen to a
short broadcast of each available channel in
turn before selecting the one you prefer.
Press and release the SCAN button to start the
channel scan and play the first channel. After
eight seconds, the scan moves to the next
channel and so on. After the last channel in an
ensemble, the first channel in the next
ensemble is played. To stop the scan and play
the current channel, press the SCAN button
again or press the Exit button.
Note: Subchannels are not included in
scanning.
Signal availability
If the digital radio signal is lost or the system
takes time to tune in to a channel, then the
display screen will show the message No
reception .
The problem may be caused by a temporary
problem, such as buildings or trees blocking
the signal, or it might be a problem with the
broadcast service operator. Try tuning to an
alternative channel and return later to see if the
problem has been resolved. If you are unable to
tune to any other channe ls, switch off the audio
unit and then try again.
PRESET BUTTONS
Storing channels as presets
You can store up to twenty digital channels (ten
each on DAB1 and DAB2 ) using the numbered
preset buttons.
1. Search for and start playing the channel
you want to preset.
EXIT
SELECT
Digital1 Network
MXR
BBC National DAB
E88123
E88126
No reception
E88127
14 : 54
1234
14 : 54
1234DAB1 [8]
BBC 5LIVE
E88128

417-01 EXTERIOR LIGHTINGFREELANDER 2 - LR2 - VIN: 000201 onwards (LHD) (02 / 04) 73
BK-VT,1.5BK-VT,1.5BK-VT,1.5BK-YE,1.5BK-VT,1.5BK-YE,1.5BK-VT,0.75
BK-VT,0.75
GY,0.5VT-GN,0.5BU-GY,1.5
BK-VT,0.75
YE-OG,1.5BN-YE,0.75
YE-VT,0.75VT-GN,1.0GY,0.5
BN-BU,1.5YE-OG,1.5GN-OG,0.75
BU-GN,0.75
BK-YE,0.75GY,0.5VT-GN,0.5
YE-VT,0.75YE-VT,0.75
BU-GN,0.75BU-GN,0.75
BK-VT,6.0
BK-YE,6.0BK-YE,2.5
BK-VT,2.5
BK-VT,2.5
BK-YE,1.5
BK-YE,1.0BK-YE,0.75
C11K-3 C11J-3
Headlamp-RH (A100)
RH (Y133)
Dipped beam-55.0 Watts
N
Sheet3C
Sheet1
C21C-19 C21D-19
levelling-RH (M129) Motor-Headlamp-Comparator
5.0 Watts
Front RH (A116)
hazard warning lamp- Turn signal indicator/21.0 WattsFront LH (A117)
hazard warning lamp- Turn signal indicator/21.0 Watts
M
Sheet3L
Sheet3K
Sheet3B
Sheet1D
Sheet1J
Sheet3H
Sheet3G
Sheet3F
Sheet3E
Sheet3
Headlamp-LH (A101)
RH (Y134) Side light-5.0 WattsRH (Y132)
Main beam-55.0 WattsComparator
Front-RH (A120)
Lamp-Side repeater-
LH (Y137) Side light-5.0 Wattslevelling-LH (M130) Motor-Headlamp-LH (Y136)
Dipped beam-55.0 WattsLH (Y135)
Main beam-55.0 Watts
5.0 WattsFront-LH (A121)
Lamp-Side repeater-
C1LS13-1
S1D132A
C1LF09A-15C1LF09A-16C1LF09A-5
C1LF09A-14C1LF09A-1
C1LS14-1C1LF09A-4C1LF09A-2C1LF09A-7C1LF08A-15C1LF08A-16
S1LS25
S1LF22
S1BB43
C1LF09A-3
C1LS14-2
C1LF08A-14
C1LF08A-4C1LF08A-2C1LF08A-7C1LF08A-5
S1LS21
C1LF08A-1C1LF08A-3
S1D130B
S1D132C
S1D132B
C1LS13-2
S1D130C
S1D130A
G1D132A-1G1D130A-1

417-01 EXTERIOR LIGHTINGFREELANDER 2 - LR2 - VIN: 000201 onwards (LHD) (04 / 04) 75
BK-GY,0.75
BK-BU,2.5BK-GY,2.5BK,0.5
BN-GN,0.75GY-OG,0.75VT-GN,0.75GY-BN,0.75GN-WH,1.0
YE-VT,0.5
BK,0.5WH-OG,0.75
BN-GN,0.75
GN-OG,0.75GN-WH,1.0VT-BN,0.75BN-GN,0.75
BK-GY,1.5
BK-GY,6.0
BK-GY,2.5
BK-BU,2.5BK-GY,1.5
Rear-LH (A135)
Lamp-Side marker-5.0 Watts
C44N-8 C44M-8
P
Sheet3W
Sheet3R
Sheet3Y
Sheet3AA
Sheet3
lamp (A125) LH stop21.0 Watts
Tail lamp unit-LH (A139)
hazard flasher lamp-Rear-LH (A119) Turn signal indicator/
21.0 WattsLH (A130)
Lamp-Reverse-21.0 WattsLH (A115)
Lamp-Tail-5.0 WattsRear-LH (A111)
Lamp-Fog guard-21.0 Watts
tail door switch (A155)
Lamp-Number plate and-
plate-RH (A127)
Lamp-Rear number5.0 Wattsplate-LH (A128)
Lamp-Rear number5.0 WattsRH (A114)
Lamp-Tail-5.0 Watts
BB
Sheet3T
Sheet3Z
Sheet3V
Sheet3S
Sheet3X
Sheet3
Tail lamp unit-RH (A140)
RH (A129)
Lamp-Reverse-21.0 WattsRear-RH (A134)
Lamp-Side marker-5.0 Watts
hazard flasher lamp-Rear-RH (A118)
Turn signal indicator/
21.0 Wattslamp (A124) RH stop21.0 WattsRear-RH (A110)
Lamp-Fog guard-21.0 Watts
C44M-5 C44N-5
C4LS35A-3C4LS35A-1C4LS04A-3C4LS35A-2C4LS35A-6C4LS35A-4
C4LS35A-5C4LS04A-2
C4LS36A-2C4LS36A-6C4LS36A-1C4LS36A-3C4LS36A-4
S4LS45A
C4LS36A-5
S4D149A
S4D149B
G4D149-1
S4D149DS4D152C
G4D151B-1

417-01 EXTERIOR LIGHTING
Headlamps - high intensity discharge
FREELANDER 2 - LR2 - VIN: 000201 onwards (LHD) (03 / 04) 78
BK-VT,0.75BK-VT,0.75BK-YE,1.0GY,0.5YE-VT,0.5GY,0.5YE-VT,0.5BU-GY,1.5YE-OG,1.5BN-YE,0.75BN-BU,1.5YE-OG,1.5GN-OG,0.75YE-VT,0.75YE-VT,0.75BU-GN,0.75BU-GN,0.75
BK-VT,0.75YE-VT,0.75BK-YE,0.75BU-GN,0.75
BK-VT,1.5BK-VT,1.5
BK-VT,2.5
BK-VT,1.5BK-VT,1.5
BK-VT,0.75
BK-VT,2.5
BK-VT,6.0
BK-YE,1.5
BK-YE,1.5BK-YE,1.5
BK-YE,0.75
BK-YE,6.0
BK-YE,2.5
5.0 Watts5.0 Watts
Front RH (A116)
hazard warning lamp- Turn signal indicator/21.0 WattsFront LH (A117)
hazard warning lamp- Turn signal indicator/21.0 Watts
E
Sheet1G
Sheet1B
Sheet1D
Sheet1
C21C-19 C21D-19
P
Sheet2R
Sheet2DD
Sheet2M
Sheet2C
Sheet1EE
Sheet2
C11K-3 C11J-3
CC
Sheet2L
Sheet2K
Sheet2F
Sheet1H
Sheet2
levelling-LH (M130)
Motor-Headlamp-Headlamp-LH (A101)levelling-RH (M129)
Motor-Headlamp-Headlamp-RH (A100)Front-RH (A120)
Lamp-Side repeater-
RH (Y132)
Main beam-55.0 WattsRH (Y134)
Side light-5.0 WattsRH (Y133)
Dipped beam-55.0 Watts
Front-LH (A121)
Lamp-Side repeater-
LH (Y135)
Main beam-55.0 WattsLH (Y137) Side light-5.0 WattsLH (Y136)
Dipped beam-55.0 Watts
S1LS25S1LS21
C1LF09A-14
C1LF09A-15
GND
C1LF09A-16
DCMIGN
C1LS14-2
C1LF09A-4C1LF09A-2C1LF09A-7C1LF09A-5C1LF08A-16C1LS14-1
IGN
C1LF09A-1C1LF09A-3
S1D132A
S1D132C
S1D132B
G1D132A-1
S1D130C
GNDC1LS13-2
C1LF08A-15C1LF08A-2C1LF08A-7C1LF08A-5
DCM
C1LF08A-4C1LS13-1
C1LF08A-14C1LF08A-1C1LF08A-3
G1D130A-1
S1D130B
S1D130A

417-01 EXTERIOR LIGHTING
Headlamps - high intensity discharge
FREELANDER 2 - LR2 - VIN: 000201 onwards (LHD) (04 / 04) 79
BK-BU,2.5BK-GY,2.5BK-GY,0.75BK,0.5
YE-GY,0.5
BN-GN,0.75YE-GY,0.75
YE-VT,0.5
GY-OG,0.75VT-GN,0.75GY-BN,0.75GN-WH,1.0BK,0.5GN-WH,1.0WH-OG,0.75
BN-GN,0.75
GN-OG,0.75VT-BN,0.75BN-GN,0.75
BK-GY,2.5BK-GY,1.5
BK-GY,1.5
BK-GY,6.0
BK-BU,2.5
Rear-LH (A135)
Lamp-Side marker-5.0 WattsRH (A114)
Lamp-Tail-5.0 Watts
V
Sheet2
C44N-1 C44M-1
stop lamp (A126)
High mounted16.0 Watts
T
Sheet2J
Sheet2W
Sheet2Z
Sheet2BB
Sheet2
Rear-LH (A111)
Lamp-Fog guard-21.0 Watts
Tail lamp unit-LH (A139)
hazard flasher lamp-Rear-LH (A119) Turn signal indicator/
21.0 Wattslamp (A125)LH stop21.0 Watts
C44N-8 C44M-8
LH (A130)
Lamp-Reverse-21.0 WattsLH (A115)
Lamp-Tail-5.0 Watts
tail door switch (A155)
Lamp-Number plate and-
plate-LH (A128)
Lamp-Rear number5.0 Wattsplate-RH (A127)
Lamp-Rear number5.0 Watts
S
Sheet2X
Sheet2Y
Sheet2AA
Sheet2N
Sheet2
Tail lamp unit-RH (A140)
RH (A129)
Lamp-Reverse-21.0 WattsRear-RH (A134)
Lamp-Side marker-5.0 WattsRear-RH (A110)
Lamp-Fog guard-21.0 Watts
hazard flasher lamp-Rear-RH (A118) Turn signal indicator/
21.0 Wattslamp (A124)RH stop21.0 Watts
C44M-5 C44N-5
C4LS50A-2
C4LS50A-1C4LS35A-6C4LS35A-3C4LS35A-1C4LS04A-3C4LS35A-2C4LS35A-4
C4LS35A-5C4LS04A-2
C4LS36A-2C4LS36A-6C4LS36A-1C4LS36A-3C4LS36A-4
S4LS45A
C4LS36A-5
S4D149A
S4D149DS4D152C
S4D149B
G4D149-1G4D151B-1

501-14 HANDLES, LOCKS, LATCHES AND ENTRY SYSTEMS
Central locking system
FREELANDER 2 - LR2 - VIN: 000201 onwards (LHD) (04 / 04) 105
GY-OG,0.75
BU-GN,0.75
BK-GY,1.5
YE-VT,0.75YE-VT,0.75
GY-RD,0.5
BU-GN,0.75
GN-OG,0.75GY-BN,0.5BU-GN,0.75YE-VT,0.75
BK-YE,2.5BK-GY,2.5
BK-BU,2.5
BK-GY,2.5BK-YE,0.75
BK-YE,1.5
BK-BU,2.5
BK-VT,1.5
BK-YE,1.5
BK-YE,6.0BK-GY,6.0
BK-VT,2.5
BK-YE,1.5
BK-VT,0.75BK-YE,0.5
BK-VT,2.5BK-YE,1.5
BK-YE,2.5BK-YE,6.0BK-VT,6.0
FS21
5.0 Amps
FET-Indicator-RH
Module (CEM) (D316)
Central ElectronicsCentral junction-box (P101)P
Sheet3
FET-Indicator-LHBATTA-1
Sheet1
Front-RH (A120)
Lamp-Side repeater-
Front LH (A117)
hazard warning lamp- Turn signal indicator/21.0 WattsFront RH (A116)
hazard warning lamp- Turn signal indicator/21.0 Watts
Headlamp-LH (A101)Tail lamp unit-LH (A139)Front-LH (A121)
Lamp-Side repeater-Tail lamp unit-RH (A140)Headlamp-RH (A100)frequency (RF) (T203)
Receiver-Radio-
C22D-7 C22C-7
C1BP02A-1
S1LS25
DI LEFT SUPPLY
C1BP02B-36C1BP02A-19
S1LS21
C1BP02B-18
DI RIGHT SUPPLY
C1BP02H-5C1BP02H-15
LIN 0
C1LS14-2
C1LS14-1
S1D132B
S1D132A
S1D132C
C1LS13-1C4LS35A-3C1LF08A-4
C1LS13-2C4LS35A-5
C1LF08A-3
C1LF09A-4C4LS36A-3
C1LF09A-3
C4LS36A-5
S1D130C
S4D149AS1D130A
S4D152C
S4D149BS1D130B
G4D149-1G1D130A-1G4D151B-1
C3PL56-3C3PL56-1
C3PL56-2
S9D139B
S2D139AS2D139B
G6D139-1G1D132A-1