engine LAND ROVER FRELANDER 2 2006 Repair Manual

18.
19.
Releas e t he harness and wit hdraw i nto engine bayarea.20.

48. NOTE: LHD il lus trati on s hown, RHD is s imil ar.48.
Unclip the harnes s t ray from t he vehi cl e bulkhead and rout e the RHSof t he harness around the brake pipes int o t he LHS of the enginebay.
49.
50. NOTE: RHD i llus t rati on s hown, LHD is s imil ar.50.
51. NOTE: RHD i llus t rati on s hown, LHD is s imil ar.51.

Inst all t he fus e cover and refi t the s ound deadening sheet.
47.
Inst all t he LH fender s pl ash s hi eld.
T orque: 6 Nm 48.
Inst all t he glove compartment l id.
Refer t o: Glove Compart ment (501-12 Ins trument Panel and
Consol e, Removal and Ins t al lat ion).
49.
Inst all t he engi ne upper s upport ins ulat or.
Refer t o: Engi ne Upper Support Ins ulat or (303-01A Engine - I6 3.2L
Petrol, Removal and Ins tall ati on).
50.
Inst all both headlamps .
Refer t o: Headl amp As sembl y (417-01 Ext eri or Li ght ing, Removal
and Inst all at ion).
51.
Inst all t he fuel fi red boos ter heater.
Refer t o: Fuel Fired Boos t er Heat er (412-02B Auxil iary Cli mate
Control, Removal and Ins tall ati on).
52.
Inst all t he ABS module.
Refer t o: Ant i-Lock Brake Sys t em (ABS) Modul e (206-09A Anti -Lock
Control, Removal and Ins tall ati on).
53.
Inst all t he brake boost er.
Refer t o: Brake Boost er (206-07 Power Brake Act uat ion, Removal
and Inst all at ion).
54.
Inst all t he s econdary bulkhead cent er panel.
Refer t o: Secondary Bulkhead Cent er Panel - TD4 2.2L Dies el (501-02 Front End Body Panel s, Removal and Ins tal lati on).
55.
Inst all t he air cleaner hous ing.
Refer t o: Air Cleaner (303-12A Intake Ai r Dis tribut ion and Fil tering -
I6 3.2L Pet rol, Removal and Ins t al lat ion).
56.
Inst all t he bumper armature.
Refer t o: Front Bumper (501-19 Bumpers , Removal and Ins tall ati on).
57.

Publi s hed: 11-May-2011
Module Communications Network - Battery Junction Box (BJB)I6 3.2L
Petrol
Removal and Inst all ati on
Removal
Remove t he bumper armature.
Refer t o: Front Bumper (501-19 Bumpers , Removal and Ins tall ati on).
1.
Remove t he air cleaner hous ing.
Refer t o: Air Cleaner (303-12A Intake Ai r Dis tribut ion and Fil tering -I6 3.2L Pet rol, Removal and Ins t al lat ion).
2.
Remove t he s econdary bulkhead cent er panel.
Refer t o: Secondary Bulkhead Cent er Panel - I6 3.2L Pet rol (501-02Front End Body Panel s, Removal and Ins t al lat ion).
3.
Remove t he brake boost er.
Refer t o: Brake Boost er (206-07 Power Brake Act uat ion, Removaland Inst all at ion).
4.
Remove t he ABS module.
Refer t o: Ant i-Lock Brake Sys t em (ABS) Modul e (206-09A Anti -LockControl, Removal and Ins tall ati on).
5.
Remove both headlamps .
Refer t o: Headl amp As sembl y (417-01 Ext eri or Li ght ing, Removaland Inst all at ion).
6.
Remove t he engi ne upper s upport ins ulat or.
Refer t o: Engi ne Upper Support Ins ulat or (303-01A Engine - I6 3.2LPetrol, Removal and Ins tall ati on).
7.
Remove t he glove compartment l id.
Refer t o: Glove Compart ment (501-12 Ins trument Panel andConsol e, Removal and Ins t al lat ion).
8.

17.
18.
Releas e t he harness and wit hdraw i nto engine bayarea.19.

Releas e t he harness cover and wit hdraw harnes s i nt oengine bay area.20.
21.
22.

Refer t o: Engi ne Upper Support Ins ulat or (303-01A Engine - I6 3.2LPetrol, Removal and Ins tall ati on).
Inst all both headlamps .
Refer t o: Headl amp As sembl y (417-01 Ext eri or Li ght ing, Removaland Inst all at ion).
49.
Inst all t he ABS module.
Refer t o: Ant i-Lock Brake Sys t em (ABS) Modul e (206-09A Anti -LockControl, Removal and Ins tall ati on).
50.
Inst all t he brake boost er.
Refer t o: Brake Boost er (206-07 Power Brake Act uat ion, Removaland Inst all at ion).
51.
Inst all t he s econdary bulkhead cent er panel.
Refer t o: Secondary Bulkhead Cent er Panel - I6 3.2L Pet rol (501-02Front End Body Panel s, Removal and Ins t al lat ion).
52.
Inst all t he air cleaner hous ing.
Refer t o: Air Cleaner (303-12A Intake Ai r Dis tribut ion and Fil tering -I6 3.2L Pet rol, Removal and Ins t al lat ion).
53.
Inst all t he bumper armature.
Refer t o: Front Bumper (501-19 Bumpers , Removal and Ins tall ati on).
54.

Publi s hed: 11-May-2011
Wiring Harnesses - Engine Wiring HarnessI6 3.2L Petrol
Removal and Inst all ati on
Removal
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
2. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
2.
Remove t he bat t ery t ray.
Refer t o: Bat t ery Tray (414-01 Bat tery, Mount ing and Cables ,Removal and Ins tall ati on).
3.
Remove t he plenum chamber.
Refer t o: Plenum Chamber (412-01 Cl imat e Control, Removal andInst all at ion).
4.
Remove t he int ake mani fol d as sembl y.
Refer t o: Int ake Mani fol d (303-01A Engi ne - I6 3.2L Petrol, Removaland Inst all at ion).
5.
Remove t he RH engine mount .
Refer t o: Engi ne Mount RH (303-01A Engi ne - I6 3.2L Petrol,Removal and Ins tall ati on).
6.
Di sconnect t he 2 engine control modul e electricalconnectors.7.

Publi s hed: 11-May-2011
Wiring Harnesses - Engine Wiring HarnessTD4 2.2L Diesel
Removal and Inst all ati on
Removal
• NOTE: Make s ure t he wi ri ng harness is rout ed correct ly. All vehicles
Remove t he air cleaner hous ing.
Refer t o: Air Cleaner (303-12B Intake Ai r Dis tribut ion and Fil tering -
TD4 2.2L Dies el, Removal and Inst all ati on).
1.
Remove t he fuel fi lt er.
Refer t o: Fuel Fil ter (310-01B Fuel Tank and Lines - TD4 2.2L Dies el ,
Removal and Ins tall ati on).
2.
Remove t he engi ne compartment clos ing panel.
Refer t o: Secondary Bulkhead Cent er Panel - TD4 2.2L Dies el (501-02 Front End Body Panel s, Removal and Ins tal lati on).
3.
Remove t he bat t ery carrier.
Refer t o: Bat t ery Tray (414-01 Bat tery, Mount ing and Cables ,
Removal and Ins tall ati on).
4.
Remove t he engi ne undershi eld.
Refer t o: Engi ne Unders hi eld (501-02 Front End Body Panel s ,
Removal and Ins tall ati on).
5.
Remove t he front RH s plas h s hi eld.
Refer t o: Fender Spl ash Shi eld (501-02 Front End Body Panel s ,
Removal and Ins tall ati on).
6.
7. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
7.
All vehicles

12-Liftgat e lat ch micros wi tch
13-Intrus i on det ecti on modul e
14-Batt ery backed s ounder and ti lt s ensor (certai n market s only) (if fi tt ed)15-Vehicle horns
16-Remot e hands et
17-RF recei ver18-St art cont rol module
19-Hood mi cros wit ch
20-Inst rument clus ter al arm LED
DOOR MODULES
The door modul es provide t he int erface bet ween the door lat ch mot ors , the door and lat ch swit ches and t he CJB. The doormodules provi de door mi cros wit ch st atus informati on and enabl e t he door mot ors on reques t from the CJB.
The rear door modul es are controll ed via t he front door modules on the Local Interconnect Net work (LIN) bus . Addit ionally,t he front door modules als o control the ext erior mi rror functi ons .
CENTRAL JUNCTION BOX
The CJB cont rol s the foll owing funct ions:
t he hornst he li ft gat e l at ch mot or and micros wit ches (i ncl udi ng the liftgat e external rel ease swi tch)t he li ft gat e ajar s wi tcht he turn s ignal indicatorsfuel fill er fl ap operati on.
The CJB als o has a connect ion t o t he Rest rai nts Cont rol Modul e (RCM) for automat ic operat ion of t he int eri or l ight s and thet urn s ignal indicators in the event of an accident.
• NOTE: If the CJB i s repl aced, the new modul e wi ll require confi guring t o t he mas ter car configurat ion us ing a Land Roverapproved diagnos t ic s yst em.
The CJB automat ically arms and di sarms t he acti ve ant i-theft sys t em when t he vehi cl e i s locked and unl ocked afters uccess ful confi rmat ion t hat a vali d remot e handset has been us ed.
INSTRUMENT CLUSTER
The ins t rument clus ter cont rol s the al arm indicat or whi ch is i ncorporated i n t he main dis play in the ins trument cl us t er.
The ins t rument clus ter als o controls , in conjuncti on wit h t he CJB, t he Engine Control Modul e (ECM) and t he Ant i-lock BrakeSyst em (ABS) module, the engine immobi lizat ion. The ECM cont rol s t he engi ne crank and fuel functi ons and the ABSmodule controls t he t il t funct ion. The EMS and ABS modul e communicate to each ot her after t he CJB proces s es the val idremot e handset i nformat ion.
Alarm Indicator
The alarm i ndi cat or is a Li ght Emit ti ng Diode (LED) locat ed in the ins trument cl us t er. W hen t he i gni ti on is off, t he i ndi cat orgives a vi sual indicati on of the act ive anti -t heft s ys tem to show if t he alarm s yst em is s et or uns et .
W hen t he i gni ti on is on, t he indicator provi des a vis ual i ndi cat ion of t he s tat us of the pas s ive anti -t heft (engi neimmobili zat ion) s yst em. If the i mmobil izati on s ys t em i s operati ng correct ly, the LED wil l be ill uminat ed for 3 s econds atignit ion on and then ext ingui s h.
If a fault exi st s i n the immobi lizat ion s yst em, t he LED wil l be eit her permanent ly ill uminated or flas hing for 60 s econds.This i ndi cat es t hat a fault exis t s and a faul t code has been recorded. After t he 60 s econd peri od, t he LED wi ll flas h atdifferent frequenci es which indicat e the nat ure of t he faul t.