wheel LEXUS ES300 2005 Owners Manual
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2005, Model line: ES300, Model: LEXUS ES300 2005Pages: 969, PDF Size: 24.08 MB
Page 743 of 969
5106B-04
F40531
SST
C92274
- POWER STEERINGRACK & PINION POWER STEERING GEAR ASSY
51-21
2596 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
OVERHAUL
NOTICE:
When installing , coat the parts indicated by the arrow with power steering fluid or molybdenum disul-
fide lithium base grease (See page 51-18).
1. PRECAUTION(See page 60-1)
2. DISCONNECT BATTERY NEGATIVE TERMINAL
3. REMOVE HORN BUTTON ASSY
(See page 60-22)
4. REMOVE STEERING WHEEL ASSY
(See page 50-8)
SST 09950-50013 (09951-05010, 09952-05010, 09953-05020, 09954-05021)
5. REMOVE FRONT WHEEL
6. REMOVE SPIRAL CABLE SUB-ASSY
(See page 50-8)
7. DISCONNECT TIE ROD ASSY LH
(a) Remove the cotter pin and nut.
(b) Using SST, remove the tie rod assy LH from the steering
knuckle.
SST 09628-6201 1
8. DISCONNECT TIE ROD ASSY RH
SST 09628-6201 1
HINT:
Remove the RH side by the same procedures with LH side.
9. DISCONNECT STEERING INTERMEDIATE SHAFT
SUB-ASSY
(a) Loosen the bolt and remove the clamp from the steering
column hole cover No.1.
(b) Disconnect the steering column hole cover No.2 from the
steering column hole cover No.1.
(c) Loosen the bolt.
Page 758 of 969
ZX9390F41951
F40556
SST
51-36
- POWER STEERINGRACK & PINION POWER STEERING GEAR ASSY
2611 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
50. INSPECT STEERING RACK END SUB-ASSY
(a) Ensure that the steering rack end sub-assy hole is not
clogged with grease.
HINT:
If the hole is clogged, the pressure inside the boot will change
after it is assembled and steering wheel is turned.
51. INSTALL STEERING RACK BOOT NO.2
(a) Install the steering rack boot No.2.
52. INSTALL STEERING RACK BOOT NO.1
HINT:
Remove the steering rack boot No.1 by the same procedures with steering rack boot No.2.
53. INSTALL STEERING RACK BOOT NO.2 CLAMP
(a) Using SST, tighten the steering rack boot No.2 clamp, as
shown in the illustration.
SST 09521-24010
Clearance: 3.0 mm (0.118 in.) or less
NOTICE:
Be careful not to damage the steering rack boot No.2.
54. INSTALL STEERING RACK BOOT NO.1 CLAMP
SST 09521-24010
NOTICE:
Be careful not to damage the steering rack boot No.1.
HINT:
Install the steering rack boot No.1 clamp by the same proce-
dures with steering rack boot No.2 clamp.
55. INSTALL STEERING RACK BOOT CLIP
(a) Using pliers, install the 2 steering rack boot clips.
56. INSTALL TIE ROD ASSY LH
(a) Screw the lock nut and tie rod assy LH onto the steering rack end sub-assy until the matchmarks are
aligned.
HINT:
After adjusting toe-in, torque the lock nut.
57. INSTALL TIE ROD ASSY RH
HINT:
Install the RH side by the same procedures with LH side.
Page 762 of 969
51-40
- POWER STEERINGRACK & PINION POWER STEERING GEAR ASSY
2615 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
68. CONNECT TIE ROD ASSY LH
(a) Connect the tie rod assy LH with the nut.
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
(b) Install a new cotter pin.
NOTICE:
If the holes for a new cotter pin are not aligned, tighten the nut further up 60.
69. CONNECT TIE ROD ASSY RH
HINT:
Install the RH side by the same procedures with LH side.
70. INSTALL FRONT WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
71. BLEED POWER STEERING FLUID (See page 51-3)
72. CHECK POWERSTEERING FLUID LEAKAGE
73. INSTALL SPIRAL CABLE SUB-ASSY
(See page 50-8)
74. CENTER SPIRAL CABLE(See page 50-8)
75. INSTALL STEERING WHEEL ASSY
(See page 50-8)
76. INSTALL HORN BUTTON ASSY
(See page 60-22)
77. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT(See page 26-5)
78. INSPECT STEERING WHEEL CENTER POINT
79. INSPECT SRS WARNING LIGHT(See page 05-826)
Page 763 of 969
2701I-09
- REAR SUSPENSIONREAR SUSPENSION SYSTEM
27-1
2383 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REAR SUSPENSION SYSTEM
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
SymptomSuspect AreaSee page
Bottoming
1. Vehicle (Overloaded)
2. Spring (Weak)
3. Shock absorber (Worn)-
27-4
27-4
Sways/pitches
1. Tire (Worn or improperly inflated)
2. Stabilizer bar (Bent or broken)
3. Shock absorber (Worn)28-1
27-16
27-4
Rear wheel shimmy
1. Tire (Worn or improperly inflated)
2. Wheel (Out of balance)
3. Shock absorber (Worn)
4. Wheel alignment (Incorrect)
5. Hub bearing (Worn)28-1
28-1
27-4
26-5
27-3
30-2
Abnormal tire wear
1. Tire (Worn or improperly inflated)
2. Wheel alignment (Incorrect)
3. Shock absorber (Worn)
4. Suspension parts (Worn)28-1
26-5
27-3
27-4
-
Page 765 of 969
2704P-06
SA3213
A
DB
Front
C
C91810
C91811
- REAR SUSPENSIONREAR WHEEL ALIGNMENT
27-3
2385 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REAR WHEEL ALIGNMENT
ADJUSTMENT
1. INSPECT TIRE (See page 28-1)
2. MEASURE VEHICLE HEIGHT (See page 26-5)
NOTICE:
Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
3. INSPECT TOE-IN
Toe-in:
Toe-in
(total)A + B: 0°22' ± 11' (0.4° ± 0.2°)
C - D: 4 ± 2 mm (0.16 ± 0.08 in.)
If the toe-in is not within the specified value, inspect and re-
place the suspension parts if necessary.
4. ADJUST TOE-IN
(a) Measure the lengths of the right and left No. 2 lower sus-
pension arms.
No. 2 lower suspension arm length difference:
1.0 mm (0.039 in.) or less
If the left-right difference is larger than 1.0 mm (0.039 in.), ad-
just it by following the procedures below.
(b) Loosen the lock nuts.
(c) Turn the right and left adjusting tube by an equal amount
to adjust toe-in.
HINT:
Try to adjust the toe-in to the center value.
One turn of the each adjusting tube will adjust the toe-in
by approximately 67' (112', 10.8 mm, 0.425 in.).
(d) Torque the lock nut.
Torque: 56 NVm (570 kgfVcm, 41 ftVlbf)
5. INSPECT CAMBER
Camber
Right-left error-1°23' ± 45' (-1.38° ± 0.75°)
45' (0.75°) or less
HINT:
Camber is not adjustable. If the measurement is not within the specification, inspect the suspension parts
for damaged and/or worn-out parts and replace them if necessary.
Page 766 of 969
2706G-03
C66631
F41030
27-4
- REAR SUSPENSIONSHOCK ABSORBER ASSY REAR LH
2386 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
SHOCK ABSORBER ASSY REAR LH
REPLACEMENT
HINT:
COMPONENTS: See page 27-2
1. REMOVE REAR WHEEL
2. REMOVE REAR SEAT CUSHION ASSY (See page 72-39)
3. REMOVE REAR SEATBACK ASSY (See page 72-39)
4. REMOVE ROOF SIDE GARNISH INNER RH (See page 76-25)
5. REMOVE ROOF SIDE GARNISH INNER LH
HINT:
Remove the LH side by the same procedures with the RH side.
6. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH (See page 72-39)
7. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
HINT:
Remove the LH side by the same procedures with the RH side.
8. REMOVE CENTER STOP LAMP ASSY (W/O SUN SHADE) (See page 65-31)
9. REMOVE REAR SEAT SHOULDER BELT COVER (See page 61-15)
10. REMOVE PACKAGE TRAY TRIM PANEL ASSY (W/ SUN SHADE) (See page 61-15)
11. REMOVE PACKAGE TRAY TRIM PANEL ASSY (W/O SUN SHADE) (See page 61-15)
12. REMOVE REAR SEAT 3 POINT TYPE BELT ASSY OUTER (See page 61-15)
13. SEPARATE REAR STABILIZER LINK ASSY LH
(a) Remove the nut and disconnect the stabilizer bar link from
the shock absorber.
HINT:
If the ball joint turns together with the nut, use a hexagon (5 mm)
wrench to hold the stud.
14. REMOVE REAR SUSPENSION SUPOPORT NO.1 COVER LH (W/O H-TEMS SUSPENSION)
15. REMOVE REAR SHOCK ABSORBER WITH COIL
SPRING
(a) Remove the 2 bolts, disconnect the flexible hose and ABS
speed sensor wire harness from shock absorber.
Page 770 of 969
C92644
w/o TEMS
w/ TEMSSST
C66631
27-8
- REAR SUSPENSIONSHOCK ABSORBER ASSY REAR LH
2390 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(d) w/o TEMS:
Tighten the nut in the center of suspension support.
(e) w/ TEMS:
Tighten the nut in the center of suspension support.
SST 09817-33190
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
HINT:
If the shock absorber has not been disassembled, it is neces-
sary to tighten the nut.
21. INSTALL REAR SUSPENSION SUPOPORT NO.1 COVER LH (W/O H-TEMS SUSPENSION)
22. INSTALL REAR SEAT 3 POINT TYPE BELT ASSY OUTER (See page 61-15)
23. INSTALL REAR STABILIZER LINK ASSY LH
(a) Install the stabilizer bar link to the shock absorber with the
nut.
Torque: 39 NVm (400 kgfVcm, 29 ftVlbf)
HINT:
If the ball joint turns together with the nut, use a hexagon (5 mm)
wrench to hold the stud.
24. INSTALL REAR WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
25. INSPECT REAR WHEEL ALIGNMENT (See page 27-3)
Page 772 of 969
2706H-02
B53735
B53736
27-10
- REAR SUSPENSIONREAR SUSPENSION ARM ASSY NO.1 LH
2392 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REAR SUSPENSION ARM ASSY NO.1 LH
REPLACEMENT
HINT:
COMPONENTS: See page 27-2
1. REMOVE REAR WHEEL
2. REMOVE EXHAUST PIPE ASSY CENTER (See page 15-2)
3. REMOVE STABILIZER BAR REAR (See page 27-16)
4. SEPARATE STRUT ROD ASSY REAR (See page 27-18)
5. SEPARATE HEIGHT CONTROL SENSOR SUB-ASSY REAR RH (See page 65-33)
6. SEPARATE REAR SUSPENSION ARM ASSY NO.2 LH
(a) Remove the bolt, nut and rear suspension arm No. 2 (out-
er side) from the rear carrier.
HINT:
Keep the nut fixed while loosening and removing the bolt.
7. SEPARATE REAR SUSPENSION ARM ASSY NO.2 RH
HINT:
Separate the RH side by the procedures with the LH side.
8. SEPARATE REAR SUSPENSION ARM ASSY NO.1 LH
(a) Remove the bolt, nut and rear suspension arm No. 1 (out-
er side) from rear axle carrier.
HINT:
Keep the nut fixed while loosening and removing the bolt.
9. SEPARATE REAR SUSPENSION ARM ASSY NO.1 RH
HINT:
Separate the RH side by the procedures with the LH side.
Page 775 of 969
C91813
C82996
C82997
- REAR SUSPENSIONREAR SUSPENSION ARM ASSY NO.1 LH
27-13
2395 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
20. STABILIZE SUSPENSION
(a) Jack up the rear axle carrier, placing a wooden block be-
tween them. Apply load to the suspension so that the
installed bolt of the suspension arm assy No. 1 (vehicle
side) is horizontally aligned with the center of the rear axle
hub.
21. FULLY TIGHTEN REAR SUSPENSION ARM ASSY
NO.1 LH
(a) Fully tighten the bolt.
Torque: 100 NVm (1,020 kgfVcm, 74 ftVlbf)
HINT:
While fixing the nut, turn the bolt.
22. FULLY TIGHTEN REAR SUSPENSION ARM ASSY NO.1 RH
HINT:
Fully tighten the RH side by the procedures with the LH side.
23. FULLY TIGHTEN REAR SUSPENSION ARM ASSY
NO.2 LH
(a) Fully tighten the bolt.
Torque: 100 NVm (1,020 kgfVcm, 74 ftVlbf)
HINT:
While fixing the nut, turn the bolt.
24. FULLY TIGHTEN REAR SUSPENSION ARM ASSY NO.2 RH
HINT:
Fully tighten the RH side by the procedures with the LH side.
25. FULLY TIGHTEN STRUT ROD ASSY REAR (See page 27-18)
26. INSTALL STABILIZER BAR REAR (See page 27-16)
27. INSTALL EXHAUST PIPE ASSY CENTER (See page 15-2)
28. INSTALL REAR WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
29. INSPECT REAR WHEEL ALIGNMENT (See page 27-3)
30. HEADLIGHT AIM ONLY (See page 65-15)
Page 776 of 969
2706I-02
C82992
C82993
C82992
27-14
- REAR SUSPENSIONREAR SUSPENSION ARM ASSY NO.2 LH
2396 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REAR SUSPENSION ARM ASSY NO.2 LH
REPLACEMENT
HINT:
COMPONENTS: See page 27-2
1. REMOVE REAR WHEEL
2. REMOVE EXHAUST PIPE ASSY CENTER (See page 15-2)
3. REMOVE STABILIZER BAR REAR (See page 27-16)
4. SEPARATE STRUT ROD ASSY REAR (See page 27-18)
5. SEPARATE HEIGHT CONTROL SENSOR SUB-ASSY REAR RH (See page 65-33)
6. SEPARATE REAR SUSPENSION ARM ASSY NO.2 LH (See page 27-10)
7. SEPARATE REAR SUSPENSION ARM ASSY NO.2 RH
HINT:
Separate the RH side by the procedures with the LH side.
8. SEPARATE REAR SUSPENSION ARM ASSY NO.1 LH (See page 27-10)
9. SEPARATE REAR SUSPENSION ARM ASSY NO.1 RH
HINT:
Separate the RH side by the procedures with the LH side.
10. REMOVE REAR SUSPENSION MEMBER SUB-ASSY (See page 27-10)
11. REMOVE REAR SUSPENSION ARM ASSY NO.2 LH
(a) Remove the bolt and rear suspension arm No. 2 (inner
side).
(b) Remove the bolt, nut and disconnect the rear suspension
arm No. 2 (outer side) from rear axle carrier.
HINT:
Keep the nut fixed while loosening and removing the bolt.
12. INSTALL REAR SUSPENSION ARM ASSY NO.2 LH
(a) Install the rear suspension arm No. 2 (inner side) with the
bolt and temporarily tighten the bolt.