engine LEXUS ES300 2005 Owner's Manual
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2005, Model line: ES300, Model: LEXUS ES300 2005Pages: 969, PDF Size: 24.08 MB
Page 215 of 969
D30464
D30466
D31338
C91731
40-16
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E)
2531 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
27. INSTALL STARTER ASSY
(a) Install the starter assy with the 2 bolts.
Torque: 37 NVm (377 kgfVcm, 27 ftVlbf)
(b) Connect the connecter.
(c) Install the starter wire and nut.
Torque: 9.8 NVm (100 kgfVcm, 87 inVlbf)
28. INSTALL WIRE HARNESS
(a) Install the wire harness and bolt.
Torque: 13 NVm (130 kgfVcm, 9 ftVlbf)
29. INSTALL WIRE HARNESS CLAMP
(a) Install the 2 clamps and 2 bolts.
Torque: 8.4 NVm (86 kgfVcm, 74 in.Vlbf)
(b) Connect the wire harnesses to the clamps.
30. INSTALL TRANSMISSION CONTROL CABLE
BRACKET NO.2
(a) Install the transmission control cable bracket No.2 with a
bolt.
Torque: 12 NVm (122 kgfVcm, 9 ftVlbf)
31. INSTALL FRONT DRIVE SHAFT ASSY LH (SEE PAGE 30-8)
32. INSTALL FRONT DRIVE SHAFT ASSY RH (SEE PAGE 30-8)
33. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE 14-29)
34. RESET MEMORY(SEE PAGE 05-604)
Page 220 of 969
4010V-04
C91925
D30865
AT0103
C91927
- AUTOMATIC TRANSMISSION / TRANSTRANSMISSION WIRE (U151E)
40-21
2536 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
TRANSMISSION WIRE (U151E)
REPLACEMENT
1. REMOVE ENGINE UNDER COVER NO.1
2. DRAIN AUTOMATIC TRANSAXLE FLUID
(a) Remove the drain plug, gasket, and drain ATF.
(b) Install a new gasket and drain plug.
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
3. REMOVE AUTOMATIC TRANSAXLE OIL PAN
SUB-ASSY
(a) Remove the 18 bolts, oil pan and gasket.
NOTICE:
Some fluid will remain in the oil pan. Remove all the pan
bolts, and carefully remove the oil pan assembly.
(b) Remove the 2 magnets from the oil pan.
(c) Examine particles in pan.
(1) Use the removed magnets to collect steel chips.
Look carefully at the chips and particles in the pan
and the magnet to anticipate the type of wear you
will find in the transaxle.
Steel (magnetic): bearing, gear and plate wear
Brass (non-magnetic): bearing wear
4. DISCONNECT TRANSMISSION WIRE
(a) Disconnect the 7 shift solenoid valve connectors.
(b) Remove the bolt and lock plate, and disconnect the ATF
temperature sensor.
Page 222 of 969
- AUTOMATIC TRANSMISSION / TRANSTRANSMISSION WIRE (U151E)
40-23
2538 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
9. ADD AUTOMATIC TRANSAXLE FLUID
10. INSPECT AUTOMATIC TRANSAXLE FLUID
(SEE PAGE 40-1)
11. INSTALL ENGINE UNDER COVER NO.1
12. RESET MEMORY (SEE PAGE 05-604)
Page 223 of 969
4010W-04
C91925
D30865
AT0103
C91927
40-24
- AUTOMATIC TRANSMISSION / TRANSTRANSMISSION VALVE BODY ASSY (U151E)
2539 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
TRANSMISSION VALVE BODY ASSY (U151E)
REPLACEMENT
1. REMOVE ENGINE UNDER COVER NO.1
2. DRAIN AUTOMATIC TRANSAXLE FLUID
(a) Remove the drain plug, gasket, and drain ATF.
(b) Install a new gasket and drain plug.
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
3. REMOVE AUTOMATIC TRANSAXLE OIL PAN
SUB-ASSY
(a) Remove the 18 bolts, oil pan and gasket.
NOTICE:
Some fluid will remain in the oil pan. Remove all the pan
bolts, and carefully remove the oil pan assembly.
(b) Remove the 2 magnets from the oil pan.
(c) Examine particles in pan.
(1) Use the removed magnets to collect steel chips.
Look carefully at the chips and particles in the pan
and the magnet to anticipate the type of wear you
will find in the transaxle.
Steel (magnetic): bearing, gear and plate wear
Brass (non-magnetic): bearing wear
4. DISCONNECT TRANSMISSION WIRE
(a) Disconnect the 7 shift solenoid valve connectors.
(b) Remove the bolt and lock plate, and disconnect the ATF
temperature sensor.
Page 227 of 969
D30865
C91925
40-28
- AUTOMATIC TRANSMISSION / TRANSTRANSMISSION VALVE BODY ASSY (U151E)
2543 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
10. I N S TA L L A U TO M AT I C T R A N S A X L E O I L PA N
SUB-ASSY
(a) Install the 2 magnets in the oil pan.
(b) Apply seal packing to 18 bolts.
Seal packing:
THREE BOND 2430 or equivalent
(c) Install a new gasket, oil pan and 18 bolts to the transaxle
case.
Torque: 7.8 NVm (80 kgfVcm, 69 in.Vlbf)
NOTICE:
Since the bolts should be seal bolts, apply seal packing to
the bolts and tighten them within 10 minutes after applying.
11. ADD AUTOMATIC TRANSAXLE FLUID
12. INSPECT AUTOMATIC TRANSAXLE FLUID (SEE PAGE 40-1)
13. INSTALL ENGINE UNDER COVER NO.1
14. RESET MEMORY (SEE PAGE 05-604)
Page 228 of 969
4010X-04
D25831
SST
D25832
SST
D25833
SST
- AUTOMATIC TRANSMISSION / TRANSFRONT DIFFERENTIAL OIL SEAL (U151E)
40-29
2544 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
FRONT DIFFERENTIAL OIL SEAL (U151E)
REPLACEMENT
1. REMOVE FRONT WHEELS
2. REMOVE ENGINE UNDER COVER NO.1
3. DRAIN AUTOMATIC TRANSAXLE FLUID
(a) Remove the drain plug, gasket and drain ATF.
(b) Install a new gasket and drain plug.
Torque: 49 NVm (500 kgfVcm, 36 ftVlbf)
4. REMOVE FRONT DRIVE SHAFT ASSY RH (SEE PAGE 30-8)
5. REMOVE FRONT DRIVE SHAFT ASSY LH (SEE PAGE 30-8)
6. REMOVE TRANSAXLE HOUSING OIL SEAL
(a) Using SST, pull out the oil seal.
SST 09308-00010
7. REMOVE DIFFERENTIAL SIDE BEARING RETAINER
OIL SEAL
(a) Using SST, pull out the oil seal.
SST 09308-00010
8. INSTALL DIFFERENTIAL SIDE BEARING RETAINER
OIL SEAL
(a) Using SST and a hammer, drive in a new oil seal.
SST 09316-6001 1 (09316-00011)
Oil seal drive in depth:
0 0.5 mm (0 0.020 in.)
(b) Coat the lip of the oil seal with MP grease.
SST 09316-6001 1 (09316-00011)
Page 239 of 969
400H6-03
D25118
D25119
40-40
- AUTOMATIC TRANSMISSION / TRANSFLOOR SHIFT ASSY
2555 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
ADJUSTMENT
1. INSPECT SHIFT LEVER POSITION
(a) When shifting from P to R position only with ignition switch ON and brake pedal, make sure that the
shifting lever moves smoothly and can be moderately operated.
(b) When starting engine, make sure that the vehicle moves forward when shifting from N to D position
and moves rearward when shifting to R position.
2. ADJUST SHIFT LEVER POSITION
(a) Loosen the nut on the control shaft lever.
(b) Push the control shaft fully downward.
(c) Return the control shaft lever 2 notches to N position.
(d) Set the shift lever to N position.
(e) While holding the shift lever lightly toward the R position
side, tighten the shift lever nut.
Torque: 14.7 N´m (150 kgf´cm, 10 ft´lbf)
(f) Start the engine and make sure that the vehicle moves
forward when shifting the lever from N to D position and
moves rearward when shifting it to R position.
Page 250 of 969
G23361DLC3
Hand-held Tester
C80826
- BRAKEBRAKE FLUID
32-5
2439 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(f) Repeat the above procedure to bleed the air out of the
brake line for each wheel.
4. BLEED BRAKE ACTUATOR ASSY (W/ VSC)
NOTICE:
After performing the usual air bleeding in the brake system,
if the height or feel of the brake pedal cannot be obtained,
perform air bleeding in the brake actuator assy with a
hand-held tester by following procedures below.
(a) Depress the brake pedal more than 20 times with the en-
gine off.
(b) Connect the hand-held tester to the DLC3, then turn the
ignition switch to the ON position.
NOTICE:
Do not start the engine.
(c) Select ºAIR BLEEDINGº on the hand-held tester.
HINT:
Please refer to the Hand-Held Tester Operator's Manual for fur-
ther details.
(d) Bleed the air out of the regular brake line in ºStep1: In-
creaseº on the hand-held tester display.
NOTICE:
Perform the air bleeding by following the steps dis-
played on the hand-held tester.
Make sure that the brake fluid in the master cylinder
reservoir tank does not become empty.
(1) Connect the vinyl tube to either one of the bleeder
plugs.
(2) Depress the brake pedal several times, then loosen
the bleeder plug of one of the above wheels with the
pedal depressed.
(3) When fluid stops coming out, tighten the bleeder
plug, then release the brake pedal.
(4) Repeat (2) and (3) until all air in the fluid is complete-
ly bled out.
(5) Tighten the bleeder plug certainly.
Torque: 8.3 NVm (85 kgfVcm, 73 in.Vlbf)
(6) Repeat the above procedure to bleed the air out of
the brake line for each wheel.
(e) Bleed the air out of the suction line in ºStep2: Inhalationº
on the hand-held tester display.
NOTICE:
Perform the air bleeding by following the steps dis-
played on the hand-held tester.
Make sure that the brake fluid in the master cylinder
reservoir tank does not become empty.
Page 254 of 969
F41698
Pedal Free play
R00934
Pedal Reserve
Distance
- BRAKEBRAKE PEDAL SUPPORT ASSY
32-9
2443 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
2. CHECK PEDAL FREE PLAY
(a) Stop the engine and depress the brake pedal several
times until there is no more vacuum left in the booster.
(b) Push in the pedal until the beginning of the resistance is
felt. Measure the distance, as shown.
Pedal free play: 1 - 6 mm (0.04 - 0.24 in.)
If incorrect, check the stop lamp switch clearance.
If the clearance is OK, then troubleshoot the brake system.
Stop lamp switch clearance:
0.5 - 2.5 mm (0.020 - 0.098 in.)
3. CHECK PEDAL RESERVE DISTANCE
(a) Release the parking brake pedal.
With engine running, depress the pedal and measure the
pedal reserve distance, as shown.
Pedal reserve distance from asphalt sheet at 490 N
(50 kgf, 110.2 lbf): More than 70 mm (2.76 in.)
If incorrect, troubleshoot the brake system.
Page 258 of 969
F42718
Pedal Free Play
R00934
Pedal Reserve
Distance
- BRAKEACCELERATOR & BRAKE PEDAL ASSY (From August,
2002)32-13
2447 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
2. CHECK PEDAL FREE PLAY
(a) Stop the engine and depress the brake pedal several
times until there is no more vacuum left in the booster.
(b) Push in the pedal until the beginning of the resistance is
felt. Measure the distance, as shown.
Pedal free play: 1 - 6 mm (0.04 - 0.24 in.)
If incorrect, check the stop lamp switch assy clearance.
If the clearance is OK, then troubleshoot the brake system.
Stop lamp switch clearance:
0.5 - 2.5 mm (0.020 - 0.098 in.)
3. CHECK PEDAL RESERVE DISTANCE
(a) Release the parking brake pedal.
With engine running, depress the pedal and measure the
pedal reserve distance, as shown.
Pedal reserve distance from asphalt sheet at 490 N
(50 kgf, 110.2 lbf): More than 63 mm (2.48 in.)
If incorrect, troubleshoot the brake system.