lock LEXUS ES300 2005 Manual PDF
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2005, Model line: ES300, Model: LEXUS ES300 2005Pages: 969, PDF Size: 24.08 MB
Page 265 of 969
F16914
F16911
32-20- BRAKEACCELERATOR & BRAKE PEDAL ASSY (From August,
2002)
2454 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
34. INSTALL BRAKE PEDAL RETURN SPRING
35. INSTALL DRIVER SIDE JUNCTION BLOCK ASSY
(a) Install the junction block assy with the 3 nuts, then con-
nect the each connector.
36. INSTALL STEERING COLUMN ASSY (SEE PAGE 50-8)
37. CONNECT STEERING SLIDING YOKE SUB-ASSY (SEE PAGE 50-8)
38. CONNECT FLOOR SHIFT PARKING LOCK CABLE ASSY (SEE PAGE 50-8)
39. INSPECT CHECK KEY INTERLOCK OPERATION (SEE PAGE 50-8)
40. INSTALL TURN SIGNAL SWITCH ASSY (SEE PAGE 50-8)
41. INSPECT SPIRAL CABLE SUB-ASSY (SEE PAGE 60-31)
42. INSTALL STEERING COLUMN COVER (SEE PAGE 50-8)
43. INSTALL STEERING COLUMN COVER LWR NO.2 (SEE PAGE 50-8)
44. INSTALL HEATER TO FOOT DUCT NO.3 (SEE PAGE 32-14)
45. INSTALL INSTRUMENT PANEL INSERT SUB-ASSY LOWER LH (SEE PAGE 71-1 1)
46. INSTALL INSTRUMENT PANEL SUB-ASSY UPPER (SEE PAGE 71-1 1)
47. INSTALL FRONT DOOR SCUFF PLATE LH (SEE PAGE 71-1 1)
48. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
49. INSTALL STEERING WHEEL ASSY (SEE PAGE 50-8)
50. INSPECT HORN BUTTON ASSY (SEE PAGE 60-22)
51. INSTALL HORN BUTTON ASSY (SEE PAGE 60-22)
52. INSTALL STEERING PAD SWITCH (SEE PAGE 82-1)
53. INSTALL CONNECTOR COVER (SEE PAGE 82-1)
54. INSTALL STEERING WHEEL COVER LOWER NO.2
55. INSPECT SRS WARNING LIGHT (SEE PAGE 05-818)
Page 267 of 969
C69097
R12236
(A)
F41707
F09717
R12236
(A) 32-22
- BRAKEBRAKE MASTER CYLINDER SUB-ASSY
2456 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(d) Push in the piston and remove the piston stopper bolt and
gasket.
(e) Remove the No.1 piston sub-assy, pulling straight out not
at an angle.
NOTICE:
If pulled out at an angle, there is a possibility that the cylin-
der bore could be damaged.
(f) Place a waste cloth and 2 wooden blocks on the work
table and lightly edges until the No.2 piston sub-assy
drops out of the cylinder.
HINT:
Make sure the distance (A) from the rag the top of the blocks
is at least 100 mm (3.94 in.).
NOTICE:
If pulled out at an angle, there is a possibility that the cylin-
der bore could be damaged.
9. REMOVE BRAKE MASTER CYLINDER KIT (W/ VSC)
(a) Place master cylinder in vise.
(b) Remove the O-ring.
(c) Push in the piston and remove the snap ring with snap
ring pliers.
NOTICE:
If pulled out at an angle, there is a possibility that the cylin-
der bore could be damaged.
(d) Push in the piston with a screwdriver, and remove the
straight pin by turning over the cylinder body.
HINT:
Tape the screwdriver tip before use.
(e) Remove the No.1 piston sub-assy, pulling straight out not
at an angle.
NOTICE:
If pulled out at an angle, there is a possibility that the cylin-
der bore could be damaged.
(f) Place a waste cloth and 2 wooden blocks on the work
table and lightly edges until the No.2 piston sub-assy
drops out of the cylinder.
HINT:
Make sure the distance (A) from the rag the top of the blocks
is at least 100 mm (3.94 in.).
NOTICE:
If pulled out at an angle, there is a possibility that the cylin-
der bore could be damaged.
Page 273 of 969
3211X-04
F40995
F40996
BR3753
32-28
- BRAKEBRAKE BOOSTER ASSY
2462 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
REPLACEMENT
1. REMOVE AIR CLEANER ASSY
2. DRAIN BRAKE FLUID
NOTICE:
Wash off the brake fluid immediately if it comes into contact with a painted surface.
3. REMOVE BRAKE MASTER CYLINDER SUB-ASSY (SEE PAGE 32-21)
SST 09023-00101
4. REMOVE VACUUM HOSE ASSY
(a) Remove the bolt and separate the vacuum hose from the
vacuum hose bracket.
(b) Slide the clip and disconnect the vacuum hose from the
brake booster.
5. REMOVE FRONT DOOR SCUFF PLATE LH (SEE PAGE 71-1 1)
6. REMOVE INSTRUMENT PANEL SUB-ASSY UPPER (SEE PAGE 71-1 1)
7. REMOVE INSTRUMENT PANEL INSERT SUB-ASSY LOWER LH (SEE PAGE 71-1 1)
8. REMOVE BRAKE PEDAL RETURN SPRING
9. REMOVE PUSH ROD PIN
(a) Remove the clip and push rod pin.
10. REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS
(a) Loosen the lock nut and remove the push rod clevis.
11. REMOVE FRONT BRAKE TUBE NO.5
(a) Using SST and remove the front brake tube No.5.
SST 09023-00101
12. REMOVE BRAKE BOOSTER ASSY
(a) Remove the 4 nuts.
(b) Pull out the brake booster assy.
Page 274 of 969
BR3753
F40996
F40995
- BRAKEBRAKE BOOSTER ASSY
32-29
2463 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
13. REMOVE BRAKE BOOSTER GASKET
14. INSTALL BRAKE BOOSTER GASKET
(a) Install a new brake booster gasket to the brake booster.
15. INSTALL BRAKE BOOSTER ASSY
(a) Install the brake booster with the 4 nuts.
Torque: 13 NVm (130 kgfVcm, 9 ftVlbf)
16. INSTALL FRONT BRAKE TUBE NO.5
(a) Using SST and install the front brake tube No.5.
Torque: 15 NVm (155 kgfVcm, 11 ftVlbf)
SST 09023-00101
17. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
(a) Install the push rod clevis and lock nut.
18. INSTALL PUSH ROD PIN
(a) Install the push rod pin and clip.
HINT:
Apply the lithium soap base glycol grease to the part indicate by arrow (see page 32-27).
19. INSTALL BRAKE PEDAL RETURN SPRING
20. INSTALL INSTRUMENT PANEL INSERT SUB-ASSY LOWER LH (SEE PAGE 71-1 1)
21. INSTALL INSTRUMENT PANEL SUB-ASSY UPPER (SEE PAGE 71-1 1)
22. INSTALL FRONT DOOR SCUFF PLATE LH (SEE PAGE 71-1 1)
23. INSTALL VACUUM HOSE ASSY
(a) Install the vacuum hose and vacuum hose bracket to the
body with a bolt.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
(b) Connect the vacuum hose to the brake booster with the
clip.
24. INSPECT AND ADJUST BRAKE BOOSTER PUSH ROD (SEE PAGE 32-21)
SST 09737-00013, 09737-00020
25. INSTALL BRAKE MASTER CYLINDER SUB-ASSY (SEE PAGE 32-21)
SST 09023-00101
26. FILL RESERVOIR WITH BRAKE FLUID
Page 284 of 969
F41866
Anti Squeal
Shim
Wear Indicator
- BRAKEFRONT BRAKE
32-39
2473 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
(2) Install the wear indicator to the 2 brake pads.
NOTICE:
When replacing worn pads, the anti squeal shims
must be replaced together with the pads.
Install the shims and pad wear indicator correctly of
which positions and directions.
(b) Install the anti squeal shim kit front (Twin piston Type).
(1) Apply the anti squeal shim with pad grease, and
install the anti squeal shim to each pad.
(2) Install the wear indicator to the 2 brake pads.
NOTICE:
When replacing worn pads, the anti squeal shims
must be replaced together with the pads.
Install the shims and pad wear indicator correctly of
which positions and directions.
38. INSTALL DISC BRAKE PAD KIT FRONT (PAD ONLY)
(a) Install the 2 disc brake pads with the pad wear indicator facing upward.
NOTICE:
There should be no oil or grease on the friction surface of the pads and the disc.
39. INSTALL DISC BRAKE CYLINDER ASSY LH
(a) Install the disc brake cylinder with the 2 bolts.
Torque: 34.3 NVm (350 kgfVcm, 25 ftVlbf)
40. CONNECT FRONT FLEXIBLE HOSE
(a) Connect a new gasket and flexible hose with the union bolt.
Torque: 29.4 NVm (300 kgfVcm, 22 ftVlbf)
HINT:
Install the flexible hose lock securely in the lock hold of the disc brake cylinder.
41. FILL RESERVOIR WITH BRAKE FLUID
42. BLEED MASTER CYLINDER (SEE PAGE 32-4)
SST 09023-00101
43. BLEED BRAKE LINE (SEE PAGE 32-4)
44. CHECK FLUID LEVEL IN RESERVOIR (SEE PAGE 32-4)
45. CHECK BRAKE FLUID LEAKAGE
46. INSTALL FRONT WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
Page 291 of 969
F41551
F41562
Cylinder Slide Pin
Cylinder Mounting
Lithium soap base glycol grease
F41558Lithium soap base glycol grease
32-46
- BRAKEREAR BRAKE
2480 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
40. INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN
(a) Using a hexagon wrench (8 mm), install the cylinder slide
pin.
Torque: 39.2 NVm (400 kgfVcm, 29 ftVlbf)
41. INSTALL REAR DISC BRAKE BUSH DUST BOOT
(a) Apply the lithium soap base glycol grease to seal surface
of a new bush dust boot.
(b) Install the bush dust boot to the cylinder slide pin.
42. INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSH
(a) Apply the lithium soap base glycol grease to a new cylin-
der slide bush.
(b) Install the cylinder slide bush to the disc brake cylinder.
43. INSTALL DISC BRAKE CYLINDER ASSY REAR LH
(a) Apply the lithium soap base glycol grease to the cylinder slide pin.
(b) Install the disc brake cylinder to the cylinder slide pin.
44. INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN
(a) Apply the lithium soap base glycol grease to the cylinder slide pin.
(b) Install the cylinder slide pin to the disc brake cylinder.
Torque: 34.3 NVm (350 kgfVcm, 25 ftVlbf)
45. CONNECT REAR LH FLEXIBLE HOSE
(a) Connect a new gasket and flexible hose with the union bolt.
Torque: 29.4 NVm (300 kgfVcm, 22 ftVlbf)
HINT:
Install the flexible hose lock securely in the lock hole of the disc brake cylinder.
46. FILL RESERVOIR WITH BRAKE FLUID
47. BLEED MASTER CYLINDER (SEE PAGE 32-4)
SST 09023-00101
48. BLEED BRAKE LINE (SEE PAGE 32-4)
49. CHECK FLUID LEVEL IN RESERVOIR (SEE PAGE 32-4)
50. CHECK BRAKE FLUID LEAKAGE
51. INSTALL REAR WHEEL
Torque: 103 NVm (1050 kgfVcm, 76 ftVlbf)
Page 309 of 969
3305G-02
F41011
Adjusting Nut
Lock Nut 33-2
- PARKING BRAKEPARKING BRAKE SYSTEM
2498 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
ADJUSTMENT
1. REMOVE REAR WHEEL
2. ADJUST PARKING BRAKE SHOE CLEARANCE(See page 33-16)
3. INSTALL REAR WHEEL
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf)
4. INSPECT PARKING BRAKE PEDAL TRAVEL
(a) Slowly depress the parking brake pedal all the way, and count the number of clicks.
Parking brake pedal travel: 3 - 6 clicks at 300 N (31 kgf, 68.3 lbf)
5. ADJUST PARKING BRAKE PEDAL TRAVEL
(a) Depress the parking brake pedal 3 notches to make a
room for the procedure, and loosen the lock nut.
(b) Return the parking brake pedal to the original position.
(c) Turn the adjusting nut until the parking brake pedal travel
is correct.
(d) Depress the parking brake pedal 3 notches to make a
room for the procedure, and tighten the lock nut.
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
(e) Return the parking brake pedal to the original position.
(f) Check whether parking brake drags or not.
(g) When operating the parking brake pedal, check that the
parking brake pedal indicator light lights up.
Page 310 of 969
3305H-02
F41008NVm (kgfVcm, ftVlbf) : Specified torque
39 (398, 29)
5.4 (55, 48 in.Vlbf)
Lock NutAdjusting NutParking Brake Control Pedal Assy
Parking Brake Switch Assy
Tension Spring
Parking Brake Cable Assy No.1
Clip
39 (398, 29)39 (398, 29)
Parking Brake Control Pedal Assy:
Parking Pedal PadReturn Spring Damper
- PARKING BRAKEPARKING BRAKE
33-3
2499 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
PARKING BRAKE
COMPONENTS
Page 313 of 969
3305I-02
F41009
F41010
33-6
- PARKING BRAKEPARKING BRAKE CONTROL PEDAL ASSY
2502 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
PARKING BRAKE CONTROL PEDAL ASSY
OVERHAUL
HINT:
COMPONENTS: See page 71-8 and 33-3
1. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSY(See page 71-1 1)
2. REMOVE COMBINATION METER ASSY(See page 71-1 1)
3. REMOVE FRONT DOOR SCUFF PLATE LH(See page 71-1 1)
4. REMOVE INSTRUMENT PANEL SUB-ASSY UPPER(See page 71-1 1)
5. REMOVE INSTRUMENT PANEL INSERT SUB-ASSY LOWER LH(See page 71-1 1)
6. REMOVE PARKING BRAKE CONTROL PEDAL ASSY
(a) Disconnect the parking brake switch connector.
(b) Remove the 2 bolts, nut and parking brake control pedal
assy.
7. DISCONNECT PARKING BRAKE CABLE ASSY NO.1
(a) Remove the lock nut, adjusting nut and clip, then discon-
nect the parking brake cable assy No.1 from the parking
brake control pedal assy.
8. REMOVE PARKING BRAKE SWITCH ASSY
(a) Remove the screw and parking brake switch assy.
9. REMOVE TENSION SPRING
10. REMOVE RETURN SPRING DAMPER
11. REMOVE PARKING PEDAL PAD
Page 314 of 969
F41010
F41009
- PARKING BRAKEPARKING BRAKE CONTROL PEDAL ASSY
33-7
2503 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
12. INSTALL PARKING PEDAL PAD
13. INSTALL RETURN SPRING DAMPER
14. INSTALL TENSION SPRING
15. INSTALL PARKING BRAKE SWITCH ASSY
(a) Install the parking brake switch assy with the screw.
16. CONNECT PARKING BRAKE CABLE ASSY NO.1
(a) Connect the parking brake cable assy No.1 with the clip,
adjusting nut and lock nut.
17. INSTALL PARKING BRAKE CONTROL PEDAL ASSY
(a) Install the parking brake control pedal assy with the 2
bolts and nut.
Torque: 39 NVm (398 kgfVcm, 29 ftVlbf)
(b) Connect the parking brake switch connector.
18. INSTALL INSTRUMENT PANEL INSERT SUB-ASSY LOWER LH
19. INSTALL INSTRUMENT PANEL SUB-ASSY UPPER
20. INSTALL FRONT DOOR SCUFF PLATE LH
21. INSTALL COMBINATION METER ASSY
22. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSY
23. INSPECT AND ADJUST PARKING BRAKE PEDAL TRAVEL(See page 33-2)