navigation system Lexus ES300h 2014 Navigation Manual

129
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “Detailed Navi. Settings” on the
“Navigation Settings” screen.
4Select “Favorite POI Categories” .
5Select the category to be changed.
6Select the desired group.
zIf the desired POI category is not on the
screen, select “List All Categories” to list
all POI categories.
7Select the desired category.
z The screen returns to the “Favorite POI
Categories” screen.
8Select “OK”.
POI CATEGORY CHANGE
(SELECT POI ICONS)
Select up to 6 POI icons to be displayed
on the map screen.

130
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “Detailed Navi. Settings” on the
“Navigation Settings” screen.
4Select ““WW Off” Function” .
5Select the screen buttons to be turned
off. The selected screen buttons will be
dimmed.
zTo set the setting as a default, select
“Default”.
6Select “OK”.
zThe previous screen will be displayed.
7Select “Save” .
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “Detailed Navi. Settings” on the
“Navigation Settings” screen.
4Select “Calibration” .
5Select the desired screen button.
SCREEN LAYOUT FUNCTION
(“WW Off” Function)
Each screen button and current street
name on the map screen can be dis-
played or hidden.CURRENT POSITION/TIRE
CHANGE CALIBRATION
The current position mark can be adjust-
ed manually. Miscalculation of the dis-
tance caused by tire replacement can
also be adjusted.
z For additional information on the accu-
racy of a current position, see “LIMITA-
TIONS OF THE NAVIGATION
SYSTEM” on page 139.

131
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
■POSITION/DIRECTION CALI-
BRATION
1Select “Position / Direction” .
2Select one of the 8 directional screen
buttons to move the cursor to the de-
sired point on the map.
3Select “OK”.
4Select either or to adjust the di-
rection of the current position mark.
5Select “OK”.
zThe map will be displayed.
■ TIRE CHANGE CALIBRATION
1To perform the distance calibration pro-
cedure, select “Tire Change” .
zThe message appears and the quick dis-
tance calibration is automatically started. A
few seconds later, a map will be displayed.
When driving, the cu rrent position mark
will be automatically corrected by GPS
signals. If GPS reception is poor due to
location, the current position mark can
be adjusted manually.
The tire change calibration function will
be used when replacing the tires. This
function will adjust miscalculation
caused by the circumference difference
between the old and new tires.

133
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
2. VEHICLE SETTINGS
1Press the “MENU” button on the
Remote Touch.
2Select “Setup” .
3Select “Vehicle” .
4Select “Maintenance” .
5Select the desired screen button.
zSetting maintenance information. (See
page 133.)
z Setting dealer. (See page 135.)
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Vehicle” on the “Setup” screen.
3Select “Maintenance” on the “Vehicle
Settings” screen.
MAINTENANCE
When the navigation system is turned
on, the “Maintenance Reminder” screen
displays when it is time to replace a part
or certain components. (See page 32.)
MAINTENANCE
INFORMATION SETTING

135
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
5Input the conditions.
6Select “OK”.
zThe screen then returns to the “Mainte-
nance” screen.
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Vehicle” on the “Setup” screen.
3Select “Maintenance” on the “Vehicle
Settings” screen.
4Select “Set Dealer”.
5If a dealer has not been registered, enter
the location of a dealer in the same way
as for a destination search. (See “DES-
TINATION SEARCH” on page 68.)
No.Function
Select to input the next maintenance
date.
Select to input the driving distance
until the next maintenance check.
Select to cancel the date and distance
conditions.
Select to reset the date and distance
conditions.
INFORMATION
●
For scheduled mainte nance information,
refer to “Warranty and Services Guide/
Owner’s Manual Supplement/Scheduled
Maintenance”.
●Depending on driving or road conditions,
the actual date and distance maintenance
should be performed may differ from the
stored date and distance in the system.
DEALER SETTING
Dealer information can be registered in
the system. With dealer information reg-
istered, route guidance to the dealer is
available.

137
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
■TO EDIT “Location”
1Select “Edit” next to “Location”.
2Select one of the 8 directional screen
buttons to move the cursor to the de-
sired point on the map screen.
3Select “OK”.
zThe previous screen will be displayed.
■ TO EDIT “Phone #”
(PHONE NUMBER)
1Select “Edit” next to “Phone #”.
2Enter the number using number keys.
3Select “OK”.
zThe previous screen will be displayed.

139
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
5. GPS (GLOBAL POSITIONING SYSTEM)
1. LIMITATIONS OF THE NAVIGATION SYSTEM
The Global Positioning System (GPS) de-
veloped and operated by the U.S. Depart-
ment of Defense provides an accurate
current position, normally using 4 or more
satellites, and in some case 3 satellites. The
GPS system has a certain level of inaccura-
cy. While the navigation system will com-
pensate for this most of the time, occasional
positioning errors of up to 300 ft. (100 m)
can and should be expected. Generally, po-
sition errors will be corrected within a few
seconds. When the vehicle is receiving signals from
satellites, the “GPS” mark appears at the
top left of the screen.
The GPS signal may be physically obstruct-
ed, leading to inaccurate vehicle position on
the map screen. Tunnel
s, tall buildings,
trucks, or even the pl acement of objects on
the instrument panel may obstruct the GPS
signals.
The GPS satellites may not send signals due
to repairs or improvements being made to
them.
Even when the navigation system is receiv-
ing clear GPS signals, the vehicle position
may not be shown accurately or inappropri-
ate route guidance may occur in some cas-
es.
This navigation system calculates the
current position using satellite signals,
various vehicle signals, map data, etc.
However, an accurate position may not
be shown depending on satellite condi-
tions, road configuration, vehicle condi-
tion or other circumstances.
NOTICE
●The installation of window tinting may
obstruct the GPS signals. Most window
tinting contains some metallic content
that will interfere with GPS signal recep-
tion of the antenna in the instrument
panel. We advise against the use of win-
dow tinting on vehicles equipped with
navigation systems.

141
5. GPS (GLOBAL POSITIONING SYSTEM)
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
zAfter replacing a tire, implement the
operation described in “TIRE CHANGE
CALIBRATION”. (See page 131.)
INFORMATION
●
This navigation system uses tire turning
data and is designed to work with factory-
specified tires for the vehicle. Installing
tires that are larger or smaller than the
originally equipped diameter may cause
inaccurate display of the current position.
The tire pressure also affects the diame-
ter of the tires, so make sure that the tire
pressure of all 4 tires is correct.

144
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
1. PHONE OPERATION
1. QUICK REFERENCE
Bluetooth® phones can be operated via the navigation system’s screen. To displa\
y the
hands-free operation screen, press the “MENU” button on the Remote Touch and
then select “Phone” , or the switch on the steering wheel.

152
1. PHONE OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3. REGISTER A Bluetooth® PHONE
1Press the “MENU” button on the
Remote Touch.
2Select “Phone” .
zThe “Phone” screen can be displayed by
pressing
on the steering wheel.
3Select “Yes” to register a phone.
zIf 5 Bluetooth® devices have already been
registered, a registered device needs to be
deleted. See “When 5 Bluetooth
® devices
have already been registered” on page
153.
4When this screen is displayed, operate
the Bluetooth
® device.
z Search for the navigation system displayed
on the system’s screen using your
Bluetooth
® device, and register the
Bluetooth® device.
For details about operating the Bluetooth®
device, see the manual that comes with it.
z A passcode is not required for SSP (Secure
Simple Pairing) compatible Bluetooth
®
phones. Depending on the type of
Bluetooth® phone being connected, a
message confirming registration may be
displayed on the Bluetooth
® phone’s
screen. Respond and operate the
Bluetooth
® phone according to the confir-
mation message.
To use the hands-free system, it is neces-
sary to register a phone with the system.
Once the phone has been registered, it
is possible to make a hands-free call.
If a Bluetooth
® phone has not been reg-
istered yet, it is necessary to register it
first according to the following proce-
dure. A Bluetooth
® phone cannot be
registered while driving.
z See “REGISTERING A Bluetooth®
DEVICE” on page 195 of additional reg-
istration when registering.