torque LEXUS GS400 2000 Service Owners Manual

A11128
Accelerator Pedal Position Sensor Connector
Throttle Control Motor Connector
Throttle Body and Intake Air Connector Assembly
Water Bypass HoseVSV Connector
for EVAP
EVAP Hose
 Gasket Air Assist Hose Engine Wire
Oil Filler Cap
No.3 Timing Belt Cover
Gasket
No.2 Timing Belt Cover
GasketThrottle
Position
Sensor
Connector
Vacuum Hose
(from Actuator for ACIS)
Water Bypass Hose
Engine Wire Protector
High±Tension
Cord w/ Clamp
No.1 Cylinder
Head Cover
Gasket
Timing Belt
x 6
Timing Belt Guide
Gasket
x 5 No.1 Timing Belt Cover
Crankshaft
Pulley
21 (210, 15)
Drive Belt Tensioner
330 (3,300, 243)
Camshaft
Timing Pulley
(VVT±i Pulley)81 (810, 60)
Straight
Screw Plug
15 (150, 11)Seal Washer
Camshaft
Timing Oil
Control Valve
Camshaft Timing
Oil Control
Valve Connector Gasket
Oil Control Valve Filter
 O±Ring
No.1 Oil PipeUnion Bolt
55 (550, 41)
Idler Pulley
Crankshaft Timing Pulley
Timing Belt Plate
Timing Belt Tensioner
N´m (kgf´cm, ft´lbf) : Specified torque
35 (350, 26)

8.0 (80, 71 in.´lbf)
27 (270, 20)
 Non±reusable part

Precoated part
Dust Boot
Engine Wire ClampPCV Hose
Vacuum Hose
(from No.2
Vacuum Pipe)
± ENGINE MECHANICAL (2JZ±GE)TIMING BELT
EM±15
1369 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

EM0D8±04
A02644
Inward
A02720
A0264110 mm Hexagon Wrench
Adhesive
A02658
Timing
Mark
Dot Mark
A02642
± ENGINE MECHANICAL (2JZ±GE)TIMING BELT
EM±23
1377 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
1. INSTALL CRANKSHAFT TIMING PULLEY
(a) Align the pulley set key with the key groove of the pulley.
(b) Slide on the timing pulley facing the flange side inward.
NOTICE:
Do not scratch the sensor part of the crankshaft timing
pulley.
(c) Install the timing belt plate with the bolt.
Torque: 8.0 N´m (80 kgf´cm, 71 in.´lbf)
2. INSTALL IDLER PULLEY
(a) Apply adhesive to 2 or 3 threads of the pivot bolt.
Adhesive:
Part No. 08833±00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(b) Using a 10 mm hexagon wrench, install the plate washer
and pulley with the pivot bolt.
Torque: 35 N´m (350 kgf´cm, 26 ft´lbf)
(c) Check that the pulley bracket moves smoothly.
3. TEMPORARILY INSTALL TIMING BELT
NOTICE:
The engine should be cold.
(a) Use the crankshaft pulley bolt to turn the crankshaft, and
align the dot mark on the crankshaft timing pulley and the
timing mark on the oil pump body.
(b) Remove any oil or water on the crankshaft timing pulley
and idler pulley, and keep them clean.
(c) Install the timing belt on the crankshaft timing pulley and
idler pulley.
HINT:
When re±using timing belt:
Align the matchmarks of the crankshaft timing pulley and timing
belt, and install the belt with the arrow pointing in the direction
of engine revolution.

A02643
A02657
60°45°
15° (Set Key Groove Angle)
Timing Mark
Sub
Timing
Mark
A02648
Align
A02659
30° EM±24
± ENGINE MECHANICAL (2JZ±GE)TIMING BELT
1378 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
4. INSTALL TIMING BELT GUIDE
Install the guide, facing the cup side outward.
5. INSTALL NO.1 TIMING BELT COVER
(a) Install the gasket to the timing belt cover.
(b) Install the timing belt cover with the 5 bolts.
Torque: 8.0 N´m (80 kgf´cm, 71 in.´lbf)
6. INSTALL CRANKSHAFT PULLEY
(a) Align the pulley set key with the key groove of the pulley,
and slide on the pulley.
(b) Check that the sub timing mark (60° mark BTDC) of the
crankshaft pulley is aligned with the timing mark º0º of the
No.1 timing belt cover.
HINT:
At this time, the crankshaft pulley set key groove and the timing
mark (TDC mark) of the crankshaft pulley are as shown the il-
lustration.
(c) Temporarily install the pulley bolt.
7. INSTALL VVT±i (INTAKE CAMSHAFT TIMING)
PULLEY
(a) Align the camshaft knock pin with the VVT±i pulley, and
push the VVT±i pulley by hand until you feel it touch the
bottom.
(b) Check that the outer circumference of the VVT±i pulley
easily rotates through 30°.

A02726
Seal WasherSet BoltHold
Straight
Screw
Plug
A02722
Mesh Part
Frame Part
A11126
5 mm
Hexagon
Wrench
A02661
Front MarkSST
± ENGINE MECHANICAL (2JZ±GE)TIMING BELT
EM±25
1379 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(c) Holding the hexagon portion of the camshaft with a
wrench.
(d) Using a 10 mm hexagon wrench, and the set bolt.
Torque: 81 N´m (810 kgf´cm, 60 ft´lbf)
(e) Using a 14 mm hexagon wrench, install the straight screw
plug with the seal washer to the set bolt.
Torque: 15 N´m (150 kgf´cm, 11 ft´lbf)
(f) Align the dot mark on the camshaft timing pulley with the
timing mark of the No.4 timing belt cover.
(g) Remove the wrench.
8. CONNECT NO.1 OIL PIPE
(a) Install the union bolt to the oil control valve filter.
NOTICE:
In case of touching the filter, avoid holding the mesh part
and holding the frame part.
(b) Install the oil pipe with 2 new gasket and the union bolt to
the No.3 camshaft bearing cap.
Torque: 55 N´m (550 kgf´cm, 41 ft´lbf)
9. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE
(See page SF±43)
10. INSTALL NO.1 CYLINDER HEAD COVER
(a) Install the cylinder head and gasket with the 6 bolts and
2 nuts.
Torque: 8.5 N´m (85 kgf´cm, 75 in.´lbf)
(b) Install the high±tension cords and clamps with the 2 bolts.
Torque: 8.0 N´m (80 kgf´cm, 71 in.´lbf)
(c) Using a 5 mm hexagon wrench, install the engine wire
protector with the bolt and nut.
11. INSTALL THROTTLE BODY AND INTAKE AIR
CONNECTOR ASSEMBLY (See page EM±5)
12. INSTALL ENGINE COVER
Install the engine cover with the 4 nuts.
13. INSTALL EXHAUST CAMSHAFT TIMING PULLEY
(a) Align the camshaft knock pin with the groove on the
pulley, and slide on the timing pulley.
(b) Slide the timing pulley on the camshaft, facing the front
mark forward.
(c) Using SST, install the pulley bolt.
SST 09960±10010 (09962±01000, 09963±01000)
Torque: 81 N´m (810 kgf´cm, 60 ft´lbf)

P10918
A02646
A02645
Turn
A02656
A02691
SST
± ENGINE MECHANICAL (2JZ±GE)TIMING BELT
EM±27
1381 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
16. INSTALL TIMING BELT TENSIONER
(a) Temporarily install the tensioner with the 2 bolts.
(b) Alternately tighten the 2 bolts.
Torque: 27 N´m (270 kgf´cm, 20 ft´lbf)
(c) Remove the 1.5 mm hexagon wrench from the tensioner
with pliers.
17. CHECK VALVE TIMING
(a) Slowly turn the crankshaft pulley 2 revolutions from TDC
to TDC.
NOTICE:
Always turn the crankshaft clockwise.
(b) Check that each pulley aligns with the timing marks as
shown in the illustration.
If the marks do not align, remove the timing belt and reinstall it.
18. TIGHTEN CRANKSHAFT PULLEY BOLT
Using SST, install the pulley bolt.
SST 09213±70010, 09330±00021
Torque: 330 N´m (3,300 kgf´cm, 243 ft´lbf)
19. INSTALL DRIVE BELT TENSIONER
Install the tensioner with the 3 bolts.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
NOTICE:
Be careful not to drop the bolts inside the timing belt cover.

A02803Plate Washer
A
B
A EM±28
± ENGINE MECHANICAL (2JZ±GE)TIMING BELT
1382 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
20. INSTALL NO.2 TIMING BELT COVER
(a) Install the gasket on the timing belt cover.
(b) Using a 5 mm hexagon wrench, install the timing belt cov-
er with the 3 bolts.
Torque: 8.0 N´m (80 kgf´cm, 71 in.´lbf)
21. INSTALL NO.3 TIMING BELT COVER
(a) Install the gasket on the timing belt cover.
(b) Using a 5 mm hexagon wrench, install the timing belt cov-
er with the 4 bolts.
Torque: 8.0 N´m (80 kgf´cm, 71 in.´lbf)
(c) Install the oil filler cap.
22. INSTALL PS PUMP AND FRONT BRACKET
(a) Temporarily install the vane pump to the bracket.
(b) Install the plate washer and front bracket with the 3 bolts.
Torque: 58 N´m (590 kgf´cm, 43 ft´lbf) for A bolts
52 N´m (530 kgf´cm, 38 ft´lbf) for B bolt
23. INSTALL DRIVE BELT (See page CH±1)
24. INSTALL RADIATOR ASSEMBLY (See page CO±23)
25. FILL ENGINE WITH COOLANT
26. START ENGINE CHECK FOR LEAKS
27. INSTALL ENGINE UNDER COVER
28. ROAD TEST
Check for abnormal noise, shock, slippage, correct shift points
and smooth operation.
29. RECHECK ENGINE COOLANT LEVEL

EM0D9±04
A09751
Air Cleaner,
MAF Meter
and Intake Air
Resonator
Assembly
PCV HoseExhaust Manifold
Case Clamp
PS Air
Hose
EVAP Hose
Air Cleaner InletMAF Meter
Connector
Heated Oxygen Sensor
Connector
 Clamp
40 (408, 32)
x 8
 Gasket
44 (440, 32)
44 (440, 32)
Pipe Support Bracket
Accelerator Cable
 Gasket
Upper Radiator
Hose
Front Exhaust Pipe
Drive Belt
Engine Under Cover
x 18
N´m (kgf´cm, ft´lbf) : Specified torque
 Non±reusable Part
Engine Cover
± ENGINE MECHANICAL (2JZ±GE)CYLINDER HEAD
EM±29
1383 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
CYLINDER HEAD
COMPONENTS

A11125
Throttle Body and Intake Air Connector AssemblyWater Bypass Hose
PCV Hose
EVAP Hose
 Gasket
Air Assist Hose
Vacuum
Hose
PS Air Hose
Air Intake Chamber
Engine Wire
Clamp
Drive Belt
TensionerClamp Bracket
Ground StrapFuel Pressure
Pulsation Damper Clamp Bracket
Water Bypass
Outlet
No.1 Water Bypass Pipe
No.3 Timing Belt Cover O±Ring
Oil Filler CapFuel Inlet Pipe
PS Air Hose
Hose
Clamp
Timing Belt
Tensioner
PS Pump Stay
Oil Dipstick
and Guide
for A/T
PS Vane Pump Water Bypass Hose
28 (280, 21)
Engine Wire
 O±Ring
No.2 Timing Belt Cover
GasketGasket
21 (210, 15)
32.5 (325, 24)
 Gasket
 Gasket
Engine Wire
Clamp
 O±Ring  O±RingOil Dipstick and
Guide for Engine
27 (270, 20)
58 (590, 43)39.2 (400, 29)N´m (kgf´cm, ft´lbf) : Specified torque
 Non±reusable Part
Dust BootEngine Wire
Clamp
No.2 Vacuum Pipe
Hose Clamp
Vacuum Control
Valve Set
EM±30
± ENGINE MECHANICAL (2JZ±GE)CYLINDER HEAD
1384 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

A11124
Ignition Coils and
High±Tension Cord
Assembly
GasketNo.2 Cylinder Head Cover
Camshaft Timing Oil Control ValveExhaust Camshaft
No.1 Camshaft Bearing Cap
Gasket
No.1 Cylinder Head Cover
No.2 Camshaft Bearing Cap x 6
x 24 x 6
20 (200, 15)
20 (200, 15)
Intake Camshaft
 O±Ring
 GasketOil Control Valve Filter
x 14 No.3 Camshaft Bearing Cap
No.1 Oil Pipe
See page EM±52
1st 35 (350, 25)
2nd Turn 90°
3rd Turn 90°
Heater Hose
55 (550, 41)
Union Bolt
18 (180, 13)Spark Plug
 Oil Seal
No.4 Timing Belt Cover
Camshaft Timing Pulley
Cylinder Head Assembly
Intake Manifold Assembly
Manifold Stay
 Cylinder Head Gasket
 Gasket
x 7
81 (810, 60)
15 (150, 11)
8.0 (80, 71 in.´lbf)
N´m (kgf´cm, ft´lbf) : Specified torque
 Non±reusable partx 12
28 (280, 21)
Starter Wire
Straight
Screw Plug
Timing Belt
± ENGINE MECHANICAL (2JZ±GE)CYLINDER HEAD
EM±31
1385 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

A02820
EM2011
EM2538
A02817
Plastigage
± ENGINE MECHANICAL (2JZ±GE)CYLINDER HEAD
EM±45
1399 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
9. INSPECT CAMSHAFTS FOR RUNOUT
(a) Place the camshaft on V±blocks.
(b) Using a dial indicator, measure the circle runout at the
center journal.
Maximum circle runout: 0.08 mm (0.0031 in.)
If the circle runout is greater than maximum, replace the cam-
shaft.
10. INSPECT CAM LOBES
Using a micrometer, measure the cam lobe height.
Standard cam lobe height:
Intake44.310 ± 44.360 mm (1.7445 ± 1.7465 in.)
Exhaust44.250 ± 44.350 mm (1.7421 ± 1.7461 in.)
Minimum cam lobe height:
Intake44.16 mm (1.7386 in.)
Exhaust44.10 mm (1.7362 in.)
If the cam lobe height is less than minimum, replace the cam-
shaft.
11. INSPECT CAMSHAFT JOURNALS
Using a micrometer, measure the journal diameter.
Journal diameter:
28.949 ± 28.965 mm (1.1397 ± 1.1404 in.)
If the journal diameter is not as specified, check the oil clear-
ance.
12. INSPECT CAMSHAFT BEARING
Check the bearings for flaking and scoring.
If the bearings are damaged, replace the bearing caps and cyl-
inder head as a set.
13. INSPECT CAMSHAFT JOURNAL OIL CLEARANCE
(a) Clean the bearing caps and camshaft journals.
(b) Place the camshafts on the cylinder head.
(c) Lay a strip of Plastigage across each of the camshaft jour-
nals.
(d) Install the bearing caps. (See page EM±52)
Torque: 20 N´m (200 kgf´cm, 14 ft´lbf)
NOTICE:
Do not turn the camshaft.
(e) Remove the bearing caps.