engine LEXUS GS400 2000 Service Service Manual

I04028

Engine Room No.3 Relay Block
Relays
A. FAN NO.1 Relay
B. FAN NO.2 Relay
C. A/C COMP Relay
D. FAN NO.3 Relay

Engine Room No.2 Relay Block
Relays
A. Horn Relay
B. ABS SOL Relay
C. TRC MTR Relay
D. ABS MTR Relay
I04027
I04028
A
B
C
D
EE. Headlight Dimmer
(Daytime Running Light No.2) Relay
A
B
C
DFuses
1. H±LP R UPR Fuse
(w/ Daytime Running Light System)
2 H±LP L UPR Fuse
(w/ Daytime Running Light System) 12 BE±18
± BODY ELECTRICALPOWER SOURCE
2319 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

BE0GC±05
BE±196
± BODY ELECTRICALAUDIO SYSTEM
2497 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
TROUBLESHOOTING
NOTICE:
When replacing the internal mechanism (computer part) of the audio system, be careful that no part
of your body or clothing comes in contact with the terminals of the leads from the IC, etc. of the re-
placement part (spare part).
HINT:
This inspection procedure is a simple troubleshooting which should be carried out on the vehicle during sys-
tem operation and was prepared on the assumption of system component troubles (except for the wires and
connectors, etc.).
Always inspect the trouble taking the following items into consideration.
Open or short circuit of the wire harness
Connector or terminal connection fault
For audio systems with anti±theft system, troubleshooting items marked ( * ) indicate that ºTrou-
bleshooting for ANTI±THEFT SYSTEMº should be carried out first.
ProblemNo.
RadioRadio not operating when power switch turned to 'ON'.1
Display indicates when power switch turned to 'ON', but no sound (including
'noise') is produced.2
Noise present, but AM ± FM not operating.3
Any speaker does not work.4
Any AM or FM does not work.5
Few preset turning bands.5
Reception poor.6
Sound quality poor.7
Preset memory disappears.8
Tape PlayerCassette tape cannot be inserted.9
Cassette tape inserted, but no power.10
Power coming in, but tape player not operating.11
Any speaker does not work.12
Sound quality poor.13
Tape jammed, malfunction with tape speed or auto±reverse.14
Cassette tape will not eject.15
CD PlayerCD cannot be inserted.16
CD inserted, but no power.17
Power coming in, but CD player not operating.18
Sound jumps.19
Sound quality poor (Volume faint).20
Any speaker does not work.21
CD will not be ejected.22
Power AmplifierNo power coming in.23
Power coming in, but power amplifier not operating.24
Any speaker does not work.25
NoiseNoise occurs26
Noise produced by vibration or shock while driving.27
Noise produced when engine starts.28
The term ºAMº includes LW,MW and SW, and the term ºFWº includes UKW.

27 Noise NOISE PRODUCED BY VIBRATION OR SHOCK WHILE DRIVING
No
Ye s Is speaker properly installed?
Noise is produced from static eletricity accumulating in the vehicle body. With vehicles stationary lightly tap each system.
Is noise produced?Install properly.
Each system faulty. Is speaker properly installed?
No
No Ye s
Ye s
28 Noise NOISE PRODUCED WHEN ENGINE STARTS
NoYe s Whistling noise which becomes high±pitched when
accelerator strongly depressed, disappears shortly
after engine stops.Generator noise.
A/C noise.
Fuel gauge noise.
Horn noise.
Ignition noise.
Turn signal noise.
Washer noise.
Engine coolant temp. gauge noise.
Wiper noise. Whining noise occurs when A/C is operating.
Scratching noise occurs during sudden acceleration, driving on rough
roads or when ignition switch is turned ON.
Clicking sound is heard when horn button is pressed, then
released. Whirring/grating sound is heard when pushed
continuously.
Murmuring sound stops when engine stops.
Tick±tack noise occurs in co±ordination with blinking
offlasher.
Noise occurs during window washer operation.
Scratching noise occurs while engine is running,
and continues a while even after engine stops.
Scraping noise in line with wiper beat.
Other type of noiseYe s
Ye s
Ye s
Ye s
Ye s
Ye s
Ye s
Ye s No
No
No
No
No
No
No
No
± BODY ELECTRICALAUDIO SYSTEM
BE±215
2516 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

BE04S±04
I05031
± BODY ELECTRICALPOWER SOURCE
BE±21
2322 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSPECTION
1. INSPECT ENGINE ROOM NO.1 JUNCTION BLOCK
CIRCUIT
(a) Remove the fuse from the junction block and inspect the
connector on junction block side.
Fuse Tester connectionConditionSpecified condition
MAIN 2 ± GroundConstantBattery positive voltage
ABS NO.1 4 ± GroundConstantBattery positive voltage
ALT 6 ± GroundConstantBattery positive voltage
ABS 8 ± GroundConstantBattery positive voltage
H±LP CLN 10 ± GroundConstantBattery positive voltage
RAD NO.1 12 ± GroundConstantBattery positive voltage
ALT±S 14 ± GroundConstantBattery positive voltage
EFI 16 ± GroundConstantBattery positive voltage
TURN HAZ 18 ± GroundConstantBattery positive voltage
TEL 20 ± GroundConstantBattery positive voltage
AM2 22 ± GroundConstantBattery positive voltage
ETCS 24 ± GroundConstantBattery positive voltage
HORN 26 ± GroundConstantBattery positive voltage
MPX±B 27 ± GroundConstantBattery positive voltage

I05032
± BODY ELECTRICALPOWER SOURCE
BE±23
2324 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
2. INSPECT ENGINE ROOM No.3 RELAY BLOCK CIR-
CUIT
Remove the relay from the relay block and inspect the connec-
tor on relay block side.
Fuse Tester connectionConditionSpecified condition
FAN NO.1 3 ± GroundIgnition switch ONBattery positive voltage
FAN NO.2 8 ± GroundIgnition switch ONBattery positive voltage
A/C COMP 13 ± GroundIgnition switch ONBattery positive voltage
FAN NO.3 17 ± GroundIgnition switch ONBattery positive voltage
DIMMER 20 ± GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.

I05033
BE±24
± BODY ELECTRICALPOWER SOURCE
2325 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
3. INSPECT ENGINE ROOM No.2 RELAY BLOCK CIR-
CUIT
Remove the relay from the relay block and inspect the connec-
tor on relay block side.
Relay Tester connectionConditionSpecified condition
HORN 1 ± GroundConstantBattery positive voltage
HORN 2 ± GroundHorn switch ONContinuity
HORN 4 ± GroundConstantBattery positive voltage
ABS SOL 5 ± GroundConstantBattery positive voltage
ABS SOL 6 ± GroundConstantContinuity
TRC MTR 11 ± GroundConstantBattery positive voltage
ABS MTR 15 ± GroundConstantBattery positive voltage
If the circuit is not as specified, inspect the circuits connected
to other parts.

BE0GD±10
I01372
Ignition SwitchRadio Assembly Tweeter
Front Speakers
Rear Speakers
Tweeter
Radio Assembly LEXUS Navigatioin
System Woofer
Power Amplifier
(NAKAMICHI made)
Driver Side Junction Block

RAD NO.2 FuseEngine Room No.1
Junction Block

ECU±B1 Fuse

RAD NO.1 Fuse
Passenger Side
Junction Block

DOME Fuse CD Auto ChangerCD Magazine
Power Amplifier
(PIONEER made)
BE±216
± BODY ELECTRICALAUDIO SYSTEM
2517 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.

BE0G3±03
I01375
Garage Door Opener Switch
Engine Room No.1
Junction Block

ECU±B Fuse
Passenger Side
Junction Block

DOME Fuse
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
BE±233
2534 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.

BE0G7±07
START
Insert the key in the key cylinder.
Under registration
Registration completion
Remove the key.
Will you register the
next key?
NoSecurity indicator blinks until the first
key is inserted. The indicator light
lights up after the key registration.
Security Indicator ON
Security Indicator
OFF
END Ye s
Security Indicator ON
(After the last key (sub±key)
has been registered, the indi-
cator goes off.)
BE±238
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
2539 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
ENGINE IMMOBILISER SYSTEM
REGISTRATION PROCEDURE
1. KEY REGISTRATION IN AUTOMATIC REGISTRATION MODE
(a) Registration of a new transponder key.
HINT:

This must be done when you install a new ECM.

The new ECM is in the automatic key code registration mode. The already fixed number of key codes
for this ECM can be registered.
On this type of vehicle, up to 3 key codes can be registered.

In the automatic registration mode, the key registered last becomes the sub±key.

1.2 Sec.
0.8 Sec.
0.25 Sec. 0.5 Sec.0.25 Sec.
1 Sec. Blinks
Code 2±1 Code2±2
0.25 Sec.
0.25 Sec.0.5 Sec. 1 Sec.
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE±239
2540 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
HINT:

When a key is not inserted in the key cylinder in the automatic registration mode, the security indicator
always lights on.

When the immobiliser system operates normally and the key is pulled out, the security indicator blinks.

When key code registration could not be performed in the automatic registration mode, code 2±1 is
output from the security indicator and when inserting the already registered key, code 2±2 is output.
(b) Automatic registration mode completion
If completing the mode forcibly when more than 1 key code have been registered in the automatic reg-
istration mode, perform the following procedures.
After 1 more key code have been registered with master key, perform step (1) or (2) without pulling
the key out or inserting the already registered key.
(1) Depress and release brake pedal 5 times or more within 15 sec.
(2) With the LEXUS hand±held tester, require automatic registration mode completion.