engine Lexus IS220d 2012 User Guide
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2012, Model line: IS220d, Model: Lexus IS220d 2012Pages: 609, PDF Size: 14.63 MB
Page 44 of 609

44
1-2. Opening, closing and locking the doors and trunk
IS250/220d/200d_EE
Battery-saving function
In the following circumstances, the entry function is disabled in order to
prevent the vehicle and electronic key batteries from discharging.
When the entry function has not been used for a month or more
When the electronic key has been left within approximately 1 m (3 ft.) of
the vehicle for 10 minutes or more
The system will resume operation when
The vehicle is locked using the door handle lock switch.
The vehicle is locked/unlocked using the wireless remote control func-
tion.
(P. 55)
The vehicle is locked/unlocked using the mechanical key. (P. 516)
Electronic key battery depletion
The standard battery life is 1 to 2 years. (The card key battery life is
about a year and a half.)
If the battery becomes low, an alarm will sound in the cabin when the
engine stops. (P. 481)
The battery becomes depleted even if the electronic key is not used
because the key always receives radio waves. If the smart entry & start
system or the wireless remote control does not operate, or the detection
area becomes smaller, the battery may be depleted. Replace the battery
when necessary.
(P. 431)
To avoid serious deterioration, do not leave the electronic key within 1 m
(3 ft.) of the following electrical appliances that produce a magnetic
field.
•TVs
• Personal computers
• Cellular phones, cordless phones and battery chargers
• Recharging cellular phones or cordless phones
• Glass top ranges
• Table lamps
Page 46 of 609

46
1-2. Opening, closing and locking the doors and trunk
IS250/220d/200d_EE
To operate the system properly
Make sure to carry the electronic key when operating the system. Do not get
the electronic key too close to the vehicle when operating the system from
the outside of the vehicle.
Depending on the position and holding condition of the electronic key, the
key may not be detected correctly and the system may not operate properly.
(The alarm may go off accidentally, or the door lock prevention may not
function.)
Note for the entry function
Even when the electronic key is within the effective range (detection
areas), the system may not operate properly in the following cases.
• The electronic key is too close to the window or outside door handle,
near the ground, or in a high place when the doors are locked or
unlocked.
• The electronic key is near the ground or in a high place, or too close to
the rear bumper center when the trunk is unlocked.
• The electronic key is on the instrument panel, rear package tray or
floor, or in the glove box when the engine is started or “ENGINE
START STOP” switch modes are changed.
Do not leave the electronic key on top of the instrument panel or near the
door pockets when exiting the vehicle. Depending on the radio wave
reception conditions, it may be detected by the antenna outside the cabin
and the door will become lockable from the outside, possibly trapping
the electronic key inside the vehicle.
As long as the electronic key is within the effective range, the doors may
be locked or unlocked by anyone.
Even if the electronic key is not inside the vehicle, it may be possible to
start the engine if the electronic key is near the window.
The doors may unlock if a large amount of water splashes on the door
handle, such as in the rain or in a car wash. (The doors will automatically
be locked after approximately 30 seconds if the doors are not opened and
closed.)
Gripping the door handle when wearing a glove may not unlock the
door.
If the wireless remote control is used to lock the doors when the elec-
tronic key is near the vehicle, there is a possibility that the door may not
be unlocked by the entry function. (Use the wireless remote control to
unlock the doors.)
A sudden approach to the effective range or door handle operation may
prevent the doors from being unlocked. In this case, return the door han-
dle to the original position and check that the doors unlock before pulling
the door handle again.
Page 48 of 609

48
1-2. Opening, closing and locking the doors and trunk
IS250/220d/200d_EE
When the vehicle is not driven for extended periods
To prevent theft of the vehicle, do not leave the electronic key within 2 m (6
ft.) of the vehicle.
Security feature
If a door is not opened within approximately 30 seconds after the vehicle is
unlocked, the anti-theft system automatically locks the vehicle again.
Alarms and warning indicators
A combination of exterior and interior alarms as well as warnings displayed
on the multi-information display is used to prevent theft of the vehicle and
unforeseeable accidents resulting from erroneous operation. Take appropri-
ate measures in response to any warning indications on the multi-informa-
tion display. (P. 473)
The following table describes circumstances and correction procedures
when only alarms are sounded.
AlarmSituationCorrection procedure
Exterior alarm
sounds once for 2
seconds
Tried to lock the doors
using the entry function
while the electronic key is
still inside the passenger
compartmentRetrieve the electronic
key from the passen-
ger compartment and
lock the doors again.
Closed the trunk while the
electronic key is still
inside and all doors are
lockedRetrieve the electronic
key from the trunk
and close the trunk
lid.
Exterior alarm
sounds once for
60 seconds
Tried to exit the vehicle
with the electronic key and
lock the doors without first
turning the “ENGINE
START STOP” switch
OFF
Turn the “ENGINE
START STOP” switch
OFF and lock the
doors again.
Exterior alarm
sounds once for
10 secondsTried to lock the vehicle
using the entry function
while a door is openClose all of the doors
and lock the doors
again.
It i lTi dt th d d
Page 49 of 609

49
1-2. Opening, closing and locking the doors and trunk
1
Before driving
IS250/220d/200d_EE
*: Vehicles with an automatic transmission only
If the smart entry & start system does not operate properly
Locking and unlocking the doors and trunk: Use the mechanical key.
(P. 516)
Starting the engine:P. 5 1 8
When the electronic key battery is fully depleted
P. 4 3 1
Customization that can be configured at any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional
It is possible to deactivate the operation signals of the system.
(Customizable featuresP. 556)
Certification for the smart entry & start system
AlarmSituationCorrection procedure
Interior alarm
pings continu-
ously
Switched to ACCESSORY
mode while the driver's
door is open (Opened the
driver's door when the
“ENGINE START STOP”
switch is in ACCESSORY
mode.)
Close the driver's
door.
Turned the “ENGINE
START STOP” switch
OFF while the driver's
Close the driver's
door
-Replace only with the same or equivalent type recommended by
the manufacturer.
-Dispose of used batteries according to the local laws.
Hereby, DENSO CORPORATION declares that this 14AAC/
14ABC/13BZK is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
Page 59 of 609

59
1
1-2. Opening, closing and locking the doors and trunk
Before driving
IS250/220d/200d_EE
Locking the front doors from the outside without a key
Move the lock button to the lock position.
Close the door while pulling the door handle.
The door cannot be locked if the “ENGINE START STOP” switch
is in ACCESSORY or IGNITION ON mode, or the electronic key
is left inside the vehicle.
Depending on the position of the electronic key, the key may not be
detected correctly and the door may be locked.
Rear door child-protector lock
The door cannot be opened
from inside the vehicle when
the locks are set.
These locks can be set to pre-
vent children from opening the
rear doors. Push down on each
rear door switch to lock both
rear doors.
STEP1
STEP2
Page 60 of 609

60
1-2. Opening, closing and locking the doors and trunk
IS250/220d/200d_EE
Automatic door locking and unlocking systems
The following functions can be set or cancelled:
*: Vehicles with an automatic transmission only
FunctionOperation
Shift position linked
door locking function*Shifting the shift lever out of P locks all
doors.
Shift position linked
door unlocking func-
tion*Shifting the shift lever to P unlocks all
doors.
Speed linked door lock-
ing functionAll doors are locked when the vehicle
speed is approximately 20 km/h (12 mph)
or higher.
Driver's door linked
door unlocking function
All doors are unlocked when the driver's
door is opened within approximately 45
seconds after turning the “ENGINE
START STOP” switch OFF.
Page 61 of 609

61
1-2. Opening, closing and locking the doors and trunk
1
Before driving
IS250/220d/200d_EESetting and canceling the function
To switch between setting and canceling, follow the procedure
below:
Close all the doors and switch the “ENGINE START
STOP” switch to IGNITION ON mode. (Perform the step 2
within 10 seconds.)
Shift the shift lever to P or N,
press and hold the driver’s door
lock switch (
or ) for
about 5 seconds then release.
The shift lever and switch posi-
tions corresponding to the
desired function to be set are
shown as follows.
Use the same procedure to can-
cel the function.
*: Vehicles with an automatic transmission only
When the setting or canceling operation is complete, all doors are
locked and then unlocked.
STEP1
STEP2
FunctionShift lever posi-
tionDriver’s door
lock switch posi-
tion
Shift position linked door lock-
ing function*
PShift position linked door
unlocking function*
Speed linked door locking func-
tion
NDriver's door linked door unlock-
ing function
Page 72 of 609

68
1-3. Adjustable components (seats, mirrors, steering wheel)
IS250/220d/200d_EE
Linking driving position memory with door unlock operation
Record your driving position to button “1”, “2” or “3” before per-
forming the following.
Carry only the key (including the card key
) to which you want to
link the driving position. If 2 or more keys are in the vehicle, the
driving position cannot be linked properly.
: If equipped
Using the wireless remote control
Turn the “ENGINE START STOP” switch OFF and close
the driver's door.
Press and hold the desired but-
ton (“1”, “2” or “3”) while
pressing on the wireless
remote control until the signal
beeps.
The driving position is recalled
when the driver's door is
unlocked using the entry func-
tion or wireless remote control
and the driver's door is opened.
To prevent unintended triggering of the alarm, open and close a
door once after a driving position has been recorded. (If a door is
not opened within 30 seconds after is pressed, the doors will be
locked again and the alarm will automatically be set.)
In case that the alarm is triggered, immediately stop the alarm.
(P. 102)
STEP1
STEP2
Page 73 of 609

69
1
1-3. Adjustable components (seats, mirrors, steering wheel)
Before driving
IS250/220d/200d_EEUsing the door lock switch
Turn the “ENGINE START STOP” switch OFF and close
the driver's door.
While pressing the desired but-
ton (“1”, “2” or “3”), press the
lock or unlock side on the
driver’s door lock switch until
the signal beeps.
The driving position is recalled
when the driver's door is
unlocked using the entry func-
tion or wireless remote control
and the driver's door is opened.
STEP1
STEP2
Page 74 of 609

70
1-3. Adjustable components (seats, mirrors, steering wheel)
IS250/220d/200d_EE
Canceling the linked door unlock operation
Turn the “ENGINE START STOP” switch OFF and close the
driver's door.
Using the wireless remote control: While pushing the “SET” but-
ton, press on the wireless remote control until the signal
beeps.
Using the door lock switch: While pressing the “SET” button, press
the lock or unlock side on the door lock switch until the signal
beeps.
Operating the driving position memory after turning the “ENGINE START
STOP” switch OFF
Memorized positions (except for the steering wheel position) can be acti-
vated up to 180 seconds after the driver’s door is opened and another 60 sec-
onds after it is closed again, even after turning the “ENGINE START
STOP” switch OFF.
To cancel seat position recall
Perform any of the following operations.
Push the “SET” button.
Push button “1”, “2” or “3”.
Adjust the seat using the switches (only cancels seat position recall).
If the battery is disconnected
The memorized positions are erased when the battery is disconnected.
CAUTION
Seat adjustment caution
Take care during seat adjustment that the seat does not strike the rear pas-
senger or squeeze your body against the steering wheel.
STEP1
STEP2