wheel Lexus IS300h 2013 Manual PDF

4677-3. Do-it-yourself maintenance
7
Maintenance and care
IS300h_EE(OM53B95E)
CAUTION
Proper inflation is critical to save tire performance
Keep your tires properly inflated. Otherwise, the following conditions may
occur and result in an accident causing death or serious injury:
Excessive wear
Uneven wear
Poor handling
Possibility of blowouts resulting from overheated tires
Poor sealing of the tire bead
Wheel deformation and/or tire separation
A greater possibility of tire damage from road hazards
NOTICE
When inspecting and adjusting tire inflation pressure
Be sure to put the tire valve caps back on.
Without the valve caps, dirt or moisture could get into the valve and cause air
leakage, which could result in an accident. If the caps are lost, replace them as
soon as possible.

4687-3. Do-it-yourself maintenance
IS300h_EE(OM53B95E)
When replacing wheels, care should be taken to ensure that they are
equivalent to those removed in load capacity, diameter, rim width and
inset
*.
Replacement wheels are available at any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional.
*: Conventionally referred to as “off-
set”.
Lexus does not recommend using the following:
Wheels of different sizes or types
Used wheels
Bent wheels that have been straightened
Use only Lexus wheel nuts and wrenches designed for use with your
aluminum wheels.
When rotating, repairing or changing your tires, check that the wheel
nuts are still tight after driving 1600 km (1000 miles).
Be careful not to damage the aluminum wheels when using tire chains.
Use only Lexus genuine balance weights or equivalent and a plastic or
rubber hammer when balancing your wheels.
When replacing wheels
The wheels of your vehicle are equipped with tire pressure warning valves and
transmitters that allow the tire pressure warning system to provide advance warn-
ing in the event of a loss in tire inflation pressure. Whenever wheels are replaced,
tire pressure warning valves and transmitters must be installed. (P. 451)
Wheels
If a wheel is bent, cracked or heavily corroded, it should be replaced.
Otherwise, the tire may separate from the wheel or cause a loss of han-
dling control.
Wheel selection
Aluminum wheel precautions

4697-3. Do-it-yourself maintenance
7
Maintenance and care
IS300h_EE(OM53B95E)
CAUTION
When replacing wheels
Do not use wheels that are a different size from those recommended in the
Owner’s Manual, as this may result in a loss of handling control.
Never use an inner tube in a leaking wheel which is designed for a tubeless
tire. Doing so may result in an accident, causing death or serious injury.
NOTICE
Replacing tire pressure warning valves and transmitters
Because tire repair or replacement may affect the tire pressure warning valves
and transmitters, make sure to have tires serviced by any authorized Lexus
dealer or repairer, or another duly qualified and equipped professional or
other qualified service shop. In addition, make sure to purchase your tire pres-
sure warning valves and transmitters at any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional.
Ensure that only genuine Lexus wheels are used on your vehicle.
Tire pressure warning valves and transmitters may not work properly with
non-genuine wheels.

4837-3. Do-it-yourself maintenance
7
Maintenance and care
IS300h_EE(OM53B95E)
Front turn signal lights (vehicles with discharge headlights)
To ensure enough space to per-
form work, turn the steering
wheel to rotate the front wheel
away from the bulb to be
replaced.
Remove the 2 fender liner
clips.
Turn the steering wheel to the left
when replacing the right side light
bulb, and turn the steering wheel
to the right when replacing the
left side light bulb.
To take out the lower clip, turn
the head of the clip to unlock it,
then remove it by pulling.
Unfasten the clamp, and pull
back the fender liner.
When unfastening the clamp,
wrap the tip of the screwdriver
with tape to protect the vehicle
from damage.
Turn the bulb base counter-
clockwise.
1
2
3

4998-1. Essential information
8
When trouble arises
IS300h_EE(OM53B95E)
Steadily step on the brake pedal with both feet and firmly depress it.
Do not pump the brake pedal repeatedly as this will increase the effort
required to slow the vehicle.
Shift the shift lever to N.
If the shift lever is shifted to N
After slowing down, stop the vehicle in a safe place by the road.
Stop the hybrid system.
If the shift lever cannot be shifted to N
Keep depressing the brake pedal with both feet to reduce vehicle speed
as much as possible.
To stop the hybrid system, press
and hold the power switch for 2
consecutive seconds or more, or
press it briefly 3 times or more in
succession.
Stop the vehicle in a safe place by the road.
If your vehicle has to be stopped in an emergency
Only in an emergency, such as if it becomes impossible to stop the vehi-
cle in the normal way, stop the vehicle using the following procedure:
1
2
3
4
3
Press and hold for 2 seconds or
more or press briefly 3 times or
4
CAUTION
If the hybrid system has to be turned off while driving
Power assist for the brakes and steering wheel will be lost, making the brake
pedal harder to depress and the steering wheel heavier to turn. Decelerate as
much as possible before turning off the hybrid system.
5

500
IS300h_EE(OM53B95E)8-2. Steps to take in an emergency
The following may indicate a problem with your transmission. Contact
any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional before towing.
The hybrid system is operating but the vehicle will not move.
The vehicle makes an abnormal sound.
If a tow truck is not available in an
emergency, your vehicle may be
temporarily towed using a cable or
chain secured to the emergency tow-
ing eyelet. This should only be
attempted on hard surfaced roads for
short distances at under 30 km/h (18
mph).
A driver must be in the vehicle to
steer and operate the brakes. The
vehicle’s wheels, drive train, axles,
steering and brakes must be in good
condition.
If your vehicle needs to be towed
If towing is necessary, we recommend having your vehicle towed by any
authorized Lexus dealer or repairer, or another duly qualified and
equipped professional or a commercial towing service, using a lift-type
truck or flat bed truck.
Use a safety chain system for all towing, and abide by all state/provincial
and local laws.
Before towing
Emergency towing

5018-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53B95E)
Take out the towing eyelet. (P. 460)
Remove the eyelet cover using a
flathead screwdriver.
To protect the bodywork, place a rag
between the screwdriver and the
vehicle body as shown in the illus-
tration.
Insert the towing eyelet into the
hole and tighten partially by
hand.
Tighten down the towing eyelet
securely using a wheel nut
wrench.
Installing towing eyelet
1
2
3
4

5028-2. Steps to take in an emergency
IS300h_EE(OM53B95E)
Do not tow with a sling-type truck
to prevent body damage.
Towing with a sling-type truck
Towing with a wheel-lift type truck
From the frontFrom the rear
Use a towing dolly under the rear
wheels.Turn the power switch to ACCES-
SORY mode so that the steering
wheel is unlocked.

5048-2. Steps to take in an emergency
IS300h_EE(OM53B95E)
Before emergency towing
Release the parking brake.
Shift the shift lever to N.
Turn the power switch to ACCESSORY (hybrid system off) or ON (hybrid
system operating) mode.
CAUTION
Observe the following precautions.
Failure to do so may result in death or serious injury.
When transporting the vehicle
Caution while towing
Use extreme caution when towing the vehicle.
Avoid sudden starts or erratic driving maneuvers which place excessive stress
on the emergency towing eyelets and the cables or chains. Always be cautious
of the surroundings and other vehicles while towing.
If the hybrid system is off, the power assist for the brakes and steering will not
function, making steering and braking more difficult.
Installing towing eyelets to the vehicle
Make sure that towing eyelets are installed securely.
If not securely installed, towing eyelets may come loose during towing.
1
2
3
Be sure to transport the vehicle with the
rear wheels raised or with all four wheels
raised off the ground. If the vehicle is
towed with the rear wheels contacting the
ground, the drivetrain and related parts
may be damaged or the electric motor
(traction motor) may generate electricity. If
the motor generates electricity, depending
on the state of the damage or malfunction,
fi d t h t i it

5058-2. Steps to take in an emergency
8
When trouble arises
IS300h_EE(OM53B95E)
NOTICE
To prevent causing serious damage to the transmission when towing using a
wheel-lift type truck
Never tow this vehicle from the front with the rear wheels on the ground.
To prevent damage to the vehicle when towing using a wheel-lift type truck
Do not tow the vehicle from the rear with the power switch off. The steering
lock mechanism is not strong enough to hold the front wheels straight.
When raising the vehicle from the rear, ensure adequate ground clearance for
towing at the opposite end of the raised vehicle. Without adequate clearance,
the vehicle could be damaged while being towed from the rear.
To prevent body damage when towing with a sling-type truck
Do not tow with a sling-type truck, either from the front or rear.
To prevent damage to the vehicle
Do not use the rear tie down hooks when your vehicle is towed.