ECO mode lexus LC500 2018 User Guide
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2018, Model line: LC500, Model: Lexus LC500 2018Pages: 528, PDF Size: 140.05 MB
Page 100 of 528
100
- $ @ - $ I @ 0 . @ 0 . & @ & &
2-1. Instrument cluster
■Changing settings of the head-up
display
Select on the multi-information dis-
play ( P.92) to change the following
settings:
Display brightness/position
Select to adjust the brightness and position
of the head-up display.
Eco Driving Indicator/tachometer
(LC500)
Select to display Eco Driving Indicator,
tachometer or no content.
Hybrid System Indicator/motor
power display/tachometer
(LC500h)
Select to display Hybrid System Indicator,
tachometer or no content.
Motor power display can be displayed
when Hybrid System In dicator is selected
while the driving mode ( P.242) is other
than the eco drive mode.
Display content
Select to enable/disable the following
items:
• Route guidance to destination
• Driving assist system status
•Compass
• Audio system operation status
Display angle
Select to adjust the angle of the head-up
display.
■Head-up display
●The head-up display may seem dark and hard to see when viewed through sun-glasses, especially polarized sunglasses.
Adjust the brightness of the head-up dis- play or remove your sunglasses.
●When the head-up display is turned off, it will remain off even if the engine switch
SORY mode or IGNITION ON mode
●The startup image will be displayed on
the head-up display after the engine switch
the head-up display switch is set to on.
■Display brightness
The brightness of the head-up display can
be adjusted on of the multi-information
display. Also, it is automatically adjusted according to the ambient brightness.
■Head-up display automatic position adjustment
If the display position is recorded into mem- ory, the head-up display will be automati-
cally adjusted to the desired position. ( P.140)
■When the 12-volt battery is discon- nected
The customize settings of the head-up dis- play will be reset.
■Customization
Settings (e.g. display) can be changed. (Customizable features: P.423)
Page 102 of 528
102
- $ @ - $ I @ 0 . @ 0 . & @ & &
2-1. Instrument cluster
is operated.
■Audio system operation status
Displayed when the audio system is
operated.
■Eco Driving Indicator/tachometer
(LC500)
Displays either of Eco Driving Indica-
tor or the tachometer.
■Hybrid System Indicator/motor
power display/tachometer
(LC500h)
Displays either of Hybrid System Indi-
cator or the tachometer.
Motor power display can be displayed
when Hybrid System Indicator is
selected while the driving mode
( P.242) is other than the eco drive
mode.
Displays the following items which are
linked to the navigation system:
■Speed limit
The speed limit on the current road.
■Street name
When the navigation system is per-
forming route guidance, the name of
the next street will be displayed on the
top of the display area.
■Route guidance to destination
Displayed when the navigation system
is performing route guidance. When
approaching an intersection, an arrow
will be displayed to indicate the sug-
gested direction of travel.
■Compass
Displays the direction of travel.
■Street name display
Only street names which are included in the map data will be displayed.
■Eco Driving Indicator
Eco Driving Indicator Zone Display
Eco driving ratio based on acceler-
ation
Zone of Eco driving
Displayed content is the same as that dis-
played on the multi-information display
(Eco Driving Indicator). For details, refer to
P.86.
■Tachometer
Displays the engine speed in revolu-
tions per minute.
Navigation system-linked dis-
play area (if equipped)
Eco Driving Indicator/tachome-
ter (LC500)
A
B
C
Page 103 of 528
103
2
- $ @ - $ I @ 0 . @ 0 . & @ & &
2-1. Instrument cluster
Vehicle status information and indicators
■Hybrid System Indicator
Charge area
Hybrid Eco area
Eco area
Power area
Displayed content is the same as that dis-
played on the meter (Hybrid System Indi-
cator). For details, refer to P.86.
■Motor power display
Charge area
Power area
Displayed content is the same as that dis-
played on the meter (Motor power dis-
play). For details, refer to P.87.
Motor power display can be displayed
when Hybrid System Indicator is selected
while the driving mode ( P.242) is other
than the eco drive mode.
■Tachometer
Displays the engine speed in revolu-
tions per minute.
Hybrid System Indicator/motor
power display/tachometer
(LC500h)
A
B
C
D
A
B
Page 107 of 528
107
2
- $ @ - $ I @ 0 . @ 0 . & @ & &
2-1. Instrument cluster
Vehicle status information and indicators
High
Multi-information display
Low
High
These images are examples only, and may
vary slightly from actual conditions.
Press the “MENU” button on the
Remote Touch, then select on the
menu screen, and then select “Trip
information” or “History”.
■Trip information
If a screen other than “Trip information”
is displayed, select “Trip information”.
Resetting the consumption data
Fuel consumption in the past 15
minutes
Current fuel consumption
Regenerated energy in the past 15
minutes (LC500h)
One symbol indicates 50 Wh. Up to 5
symbols are shown.
Average vehicle speed since the
engine
Elapsed time since the engine
Cruising range
Average fuel consumption for the past 15
minutes is divided by color into past aver-
ages and averages attained since the
engine switch
turned to IGNITION ON mode
consumption as a reference.
The image is an example only, and may
vary slightly from actual conditions.
■History
If a screen other than “History” is dis-
played, select “History”.
Best recorded fuel consumption
Latest fuel consumption
Previous fuel consumption record
Resetting the History data
Updating the latest fuel consump-
Consumption
B
A
B
A
B
C
D
E
F
G
A
B
C
D
E
Page 123 of 528
123
3
- $ @ - $ I @ 0 . @ 0 . & @ & &
3-2. Opening, closing and locking the doors and trunk
Before driving
■Effective range (areas within which the electronic key is detected)
When locking or unlocking the doors
The system can be operated when the
electronic key is within about 0.7 m (2.3
ft.) of an outside door handle. (Only the
doors detecting the key can be oper-
ated.)
When opening the trunk
The system can be operated when the
electronic key is within about 0.7 m (2.3
ft.) of the trunk release button.
When starting the engine
The system can be operated when the
electronic key is inside the vehicle.
■If an alarm sounds or a warning message is displayed
An alarm sounds and warning messages are displayed on the multi-information dis-play to protect against unexpected acci-
dents or theft of the vehicle resulting from erroneous operation. When a warning mes-sage is displayed, take appropriate mea-
sures based on the displayed message. ( P.378)
When only an alarm sounds, circumstances and correction procedures are as follows.
●When an exterior alarm sounds once for 5 seconds
●When an interior alarm sounds continu-ously
■If “Key Detected in Vehicle” is shown on the multi-information display
An attempt was made to lock the doors using the smart entry & start system while the electronic key was still inside the vehi-
cle. Retrieve the electronic key from the vehicle and lock the doors again.
A
B
C
SituationCorrection proce-
dure
The trunk was
closed while the
electronic key was
still inside the trunk
and both side doors
were locked.
Retrieve the elec-
tronic key from the
trunk and close the
trunk lid.
An attempt was
made to lock the
vehicle while a door
was open.
Close both side
doors and lock the
doors again.
SituationCorrection proce-
dure
The engine switch
turned to ACCES-
SORY mode while
the driver’s door was
open (or the driver’s
door was opened
while the engine
switch
ACCESSORY
mode).
Turn the engine
switch
the driver’s door.
The engine switch
turned off while the
driver’s door was
open.
Close the driver’s
door.
Page 125 of 528
125
3
- $ @ - $ I @ 0 . @ 0 . & @ & &
3-2. Opening, closing and locking the doors and trunk
Before driving
• The electronic key is near the ground or in a high place, or too close to the center of the rear bumper when the trunk is
opened. • The electronic key is on the instrument panel, rear package tray or floor, or in the
door pockets or glove box when the engine
changed.
●Do not leave the electronic key on top of
the instrument panel or near the door pockets when exiting the vehicle. Depending on the radio wave reception
conditions, it may be detected by the antenna outside the cabin and the doors will become lockable from the outside,
possibly trapping the electronic key inside the vehicle.
●As long as the electronic key is within the effective range, the doors may be locked or unlocked by anyone. However, only
the doors detecting the electronic key can be used to unlock the vehicle.
●Even if the electronic key is not inside the vehicle, it may be possible to start the engine
key is near the window.
●The doors may unlock or lock if a large amount of water splashes on the door handle, such as in the rain or in a car
wash, when the electronic key is within the effective range. (The doors will auto- matically be locked after approximately
30 seconds if the doors are not opened and closed.)
●If the wireless remote control is used to lock the doors when the electronic key is near the vehicle, there is a possibility that
the door may not be unlocked by the entry function. (Use the wireless remote control to unlock the doors.)
●If the door handle becomes wet while the electronic key is within the effective
range, the door may lock and unlock repeatedly. In this case, follow the follow-ing correction procedures to wash the
vehicle: • Place the electronic key in a location 2 m (6 ft.) or more away from the vehicle.
(Take care to ensure that the key is not stolen.)• Set the electronic key to battery-saving
mode to disable the smart entry & start system. ( P.124)
●If the electronic key is inside the vehicle and a door handle becomes wet during a car wash, a message may be shown on
the multi-information display and a buzzer will sound outside the vehicle. To turn off the alarm, lock both side doors.
●If an outside door handle is not retracted during a car wash, a door may be opened
or an outside door handle may be dam- aged. Make sure that the outside door handles are retracted before using the
car wash.
●A sudden handle operation or a handle
operation immediately after entering the effective range may prevent the doors from being unlocked. Touch the door
unlock sensor and check that the doors are unlocked before pulling the door handle again.
●Unlocking the vehicle may take more time if another electronic key is within the
effective range.
■When the vehicle is not driven for extended periods
●To prevent theft of the vehicle, do not leave the electronic key within 2 m (6 ft.)
of the vehicle.
●The smart entry & start system can be
deactivated in advance.
■To operate the system properly
●Make sure to carry the electronic key
when operating the system. Do not get the electronic key too close to the vehicle when operating the system from the out-
side of the vehicle. Depending on the position and holding condition of the electronic key, the key
may not be detected correctly and the system may not operate properly. (The alarm may go off accidentally, or the door
lock prevention function may not oper- ate.)
●Do not leave the electronic key inside the
Page 140 of 528
140
- $ @ - $ I @ 0 . @ 0 . & @ & &
3-3. Adjusting the seats
1Turn the engine switch
2 Check that the shift position is in P.
3 Adjust the driver’s seat, steering
wheel, outside rear view mirrors
and head-up display to the desired
positions.
4 While pressing the “SET” button, or
within 3 seconds after the “SET”
button is pressed, press button “1”,
“2” or “3” until the buzzer sounds.
If the selected button has already been preset, the previously recorded position
WARNING
■Lever-operated “Front, Fold & Return” seat
●Before operating the lever-operated “Front, Fold & Return” seat, ensure that any surrounding passengers or objects
will not contact the seat.
●Make sure the seatback is locked securely before driving.
●Never operate the lever-operated “Front, Fold & Return” seat while the
vehicle is moving.
■Jam protection function
Do not use a hand, foot, or any other part
of your body to intentionally activate the jam protection function.
Driving position memory
This feature automatically adjusts
the positions of the driver’s seat,
steering wheel, outside rear view
mirrors and head-up display (if
equipped) to suit your preferences.
Up to 3 different driving positions
can be recorded.
Each electronic key can be regis-
tered to recall your preferred driv-
ing position.
Recording a driving position into
memory
Page 141 of 528
141
3
- $ @ - $ I @ 0 . @ 0 . & @ & &
3-3. Adjusting the seats
Before driving
will be overwritten.
■Seat positions that can be memorized
( P.138)
The adjusted positions other than the posi-
tion adjusted by lumbar support switch can be recorded.
■In order to correctly use the driving position memory function
If a seat position is already in the furthest possible position and the seat is operated in
the same direction, the recorded position may be slightly different when it is recalled.
1 Turn the engine switch
2 Check that the shift position is in P.
3 Press one of the buttons for the
driving position you want to recall
until the buzzer sounds.
■To stop the position recall operation
part-way through
Perform any of the following:
●Press the “SET” button.
●Press button “1”, “2” or “3”.
●Operate any of the seat adjustment
switches (only cancels seat position recall).
●Operate the tilt and telescopic steering control switch (only cancels steering
wheel position recall).
■Operating the driving position memory after turning the engine switch
Recorded seat positions can be activated up to 180 seconds after the driver’s door is
opened and another 60 seconds after it is closed again.
■Registering procedure
Record your driving position to button
“1”, “2” or “3” before performing the
following:
WARNING
■Seat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear passen-
ger or squeeze your body against the steering wheel.
Recalling a driving position
Registering/cancel ing/recalling
a driving position to an elec-
tronic key (memor y recall func-
tion)
Page 142 of 528
142
- $ @ - $ I @ 0 . @ 0 . & @ & &
3-3. Adjusting the seats
Carry only the key you want to register,
and then close the driver’s door.
If 2 or more keys are in the vehicle, the
driving position cannot be recorded
properly.
1 Turn the engine switch
2 Check that the shift position is in P.
3 Recall the driving position that you
want to record.
4 While pressing the recalled button,
press and hold the door lock switch
(either lock or unlock) until the
buzzer sounds.
If the button could not be registered, the buzzer sounds continuously for approxi-mately 3 seconds.
■Cancelation procedure
1 Carry only the key you want to can-
cel and then close the driver’s door.
If 2 or more keys are in the vehicle, the driving position cannot be canceled prop-erly.
2 Turn the engine switch
3 While pressing the “SET” button,
press and hold the door lock switch
(either lock or unlock) until the
buzzer sounds twice.
If the button could not be canceled, the buzzer sounds continuously for approxi-
mately 3 seconds.
■Recall procedure
1 Make sure that the doors are
locked before recalling the driving
position. Carry the electronic key
that has been registered to the driv-
ing position, and then unlock and
open the driver’s door using the
smart entry & start system or wire-
less remote control.
The driving position will move to the recorded position (not including the steer-
ing wheel and head-up display).
If the driving position is in a position that
has already been recorded, the seat and outside rear view mirrors will not move.
2 Turn the engine switch
IGNITION ON mode
The steering wheel and head-up display will move to the recorded position.
■Recalling the driving position using the
memory recall function
●Different driving positions can be regis-
tered for each electronic key. Therefore, the driving position that is recalled may be different depending on the key being
carried.
●If the passenger’s door is unlocked with
the smart entry & start system, the driving position cannot be recalled. In this case, press the driving position button which
has been set.
■Customization
The unlock door settings of the memory
recall function can be changed. (Customizable features: P.423)
Page 148 of 528
148
- $ @ - $ I @ 0 . @ 0 . & @ & &
3-4. Adjusting the steering wheel and mirrors
■Using the switch
Press the switch to fold the mirrors.
Press it again to extend them to the original
position.
■Setting automatic mode
Automatic mode allows the folding or
extending of the mirrors to be linked to
locking/unlocking of the doors.
Press the “AUTO” switch to set auto-
matic mode.
The indicator will come on.
Pressing the switch on ce more will return
to manual mode.
■When disconnecting and reconnecting 12-volt battery terminals
The automatic folding/extending mirror function will return to off as default. To turn the function on, press the switch again to
select on.
■Using automatic mode in cold weather
When automatic mode is used in cold
weather, the door mirror could freeze up and automatic stowing and return may not be possible. In this case, remove any ice and
snow from the door mirror, then either operate the mirror using manual mode or move the mirror by hand.
■Customization
The automatic mirror folding and extending operation can be changed.
(Customizable features: P.423)
When either “L” or “R” of the mirror
select switch is selected, the outside
rear view mirrors will automatically
angle downwards when the vehicle is
reversing in order to give a better view
WARNING
■When the outside rear view mirror defoggers are operating
Do not touch the outside rear view mir- ror surfaces, as they can become very hot and burn you.
Folding and extending the mir-
rors
A
WARNING
■When a mirror is moving
To avoid personal injury and mirror mal- function, be careful not to get your hand caught by the moving mirror.
Linked mirror function when
reversing