high beam lexus LC500 2018 Owner's Manual

3
-$@-$I@0.@0.&@ &&

TABLE OF CONTENTS
1
6
5
4
3
2
8
7
Power (ignition) switch (LC500h)
............................................................ 167
EV drive mode (LC500h)......... 171
Automatic transmission (LC500)
............................................................ 173
Hybrid transmission (LC500h)
............................................................ 179
Turn signal lever ............................ 186
Parking brake ................................. 187
Brake Hold....................................... 189
4-3. Operating the lights and wipers
Headlight switch ............................. 191
Automatic High Beam ................ 193
Fog light switch .............................. 196
Windshield wipers and washer 196
4-4. Refueling
Opening the fuel tank cap......... 201
4-5. Using the driving support systems
Lexus Safety System+ ................ 203
PCS (Pre-Collision System)..... 210
LKA (Lane-Keeping Assist) ..... 218
RSA (Road Sign Assist)............. 226
Dynamic radar cruise control with
full-speed range......................... 229
Cruise control ............................... 239
Driving mode select switch...... 242
Lexus parking assist-sensor..... 243
BSM (Blind Spot Monitor) ....... 248
Active rear wing ........................... 259
Driving assist systems................. 262
4-6. Driving tips
Hybrid vehicle driving tips
(LC500h) .................................... 267
Winter driving tips ....................... 269
5-1. Remote Touch
Remote Touch................................ 274
5-2. Lexus Climate Concierge
Lexus Climate Concierge ....... 278
5-3. Using the air conditioning system
Automatic air conditioning system
.......................................................... 280
Heated steering wheel/seat heat-
ers/seat ventilators .................. 288
5-4. Using the interior lights
Interior lights list ............................. 291
5-5. Using the storage features
List of storage features ............... 293
Trunk features ............................... 295
5-6. Using the other interior features
Other interior features ............... 297
ERA-GLONASS ........................ 299
6-1. Maintenance and care
Cleaning and protecting the vehi-
cle exterior................................... 304
Cleaning and protecting the vehi-
cle interior .................................... 307
6-2. Maintenance
Maintenance requirements ....... 312
6-3. Do-it-yourself maintenance
Do-it-yourself service precautions
............................................................ 314
Hood ................................................... 316
Positioning a floor jack ................316
5Interior features
6Maintenance and care

84
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
panel.
The indicators inform the driver of the
operating state of the vehicle’s various
systems.
WARNING
■If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not come on
when you start the engine , this could mean that these systems are not available to help protect you in an
accident, which could result in death or serious injury. Have the vehicle inspected by any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer immediately if this occurs.
Indicators
Turn signal indicator
( P.186)
Tail light indicator ( P.191)
Headlight high beam indica-
tor ( P.192)
(If equipped)
Automatic High Beam indica-
tor*1 ( P.193)
Rear fog light indicator
( P.196)
(If equipped)
Gear Shift Indicator*2
( P.178, 185)
Cruise control indicator*2
( P.229, 239)
(If equipped)
Dynamic radar cruise control
indicator*2 ( P.229)
Cruise control “SET” indica-
tor*2 ( P.229, 239)
(white)
LKA indicator*2 (P.218)
(green)
LKA indicator*2 (P.218)
(orange)
LKA indicator*2, 3 (P.218)
Lexus parking assist-sensor
indicator ( P.243)
Slip indicator*1, 3 ( P.263)
VSC OFF indicator*1
( P.263)
PCS warning light*1, 4
( P.212)
(If equipped)
BSM (Blind Spot Monitor)
outside rear view mirror indi-
cators*5, 6 ( P.248)
(If equipped)
BSM (Blind Spot Monitor)
indicator ( P.248)
(If equipped)
RCTA (Rear Crossing Traffic
Alert) indicator ( P.248)
Brake hold standby indica-
tor*1 ( P.189)
Brake hold operated indica-
tor*1 ( P.189)
Security indicator*7 ( P.70,
76)
Smart entry & start system
indicator*2 ( P.163)

4
153
-$@-$I@0.@0.&@ &&

4
Driving
Driving
4-1. Before driving
Driving the vehicle..................... 154
Cargo and luggage .................... 161
Trailer towing ............................... 162
4-2. Driving procedures
Engine (ignition) switch (LC500)
......................................................... 163
Power (ignition) switch (LC500h)
......................................................... 167
EV drive mode (LC500h)...... 171
Automatic transmission (LC500)
......................................................... 173
Hybrid transmission (LC500h)
......................................................... 179
Turn signal lever ......................... 186
Parking brake .............................. 187
Brake Hold.................................... 189
4-3. Operating the lights and wipers
Headlight switch .......................... 191
Automatic High Beam ............. 193
Fog light switch ........................... 196
Windshield wipers and washer
......................................................... 196
4-4. Refueling
Opening the fuel tank cap...... 201
4-5. Using the driving support sys-
tems
Lexus Safety System+ ............. 203
PCS (Pre-Collision System) . 210
LKA (Lane-Keeping Assist) .. 218
RSA (Road Sign Assist).......... 226
Dynamic radar cruise control with
full-speed range ...................... 229
Cruise control ............................ 239
Driving mode select switch ... 242
Lexus parking assist-sensor .. 243
BSM (Blind Spot Monitor) .... 248
Active rear wing ........................ 259
Driving assist systems .............. 262
4-6. Driving tips
Hybrid vehicle driving tips
(LC500h).................................. 267
Winter driving tips .................... 269

192
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
or .
■Light reminder buzzer
A buzzer sounds when the engine switch is turned off or turned to ACCESSORY mode and the driver’s door
is opened while the lights are turned on.
■Automatic headlight leveling system
The level of the headlights is automatically adjusted according to the number of pas-sengers and the loading condition of the
vehicle to ensure that the headlights do not interfere with other road users.
■12-volt battery-saving function
In order to prevent 12-volt the battery of the vehicle from discharging, if the light switch
is in the or position when the
engine switch is turned off the 12-volt battery savi ng function will oper-
ate and automatically turn off all the lights after approximately 20 minutes.
When the engine switch is turned to IGNITION ON mode , the 12-volt battery-saving function
will be disabled.
When any of the following are performed,
the 12-volt battery-saving function is can- celed once and then reactivated. All the lights will turn off automatically 20 minutes
after the 12-volt battery- saving function has been reactivated:
●When the headlight switch is operated
●When a door is opened or closed
■Welcome light illumination control
The front position, tail lights and license plate lights automatically turn on at night
when the doors are unlocked using the entry function or wireless remote control if
the light switch is in the position.
■Customization
Settings (e.g. light sens or sensitivity) can be
changed. (Customizable features: P.423)
1With the headlights on, push the
lever away from you to turn on the
high beams.
Pull the lever toward you to the center
position to turn the high beams off.
2 Pull the lever toward you and
release it to flash the high beams
once.
You can flash the high beams with the
headlights on or off.
This system allows the headlights and
front position lights to be turned on for
30 seconds when the engine switch
is off.
Pull the lever toward you and release it
with the light switch is in after turn-
ing the engine switch
off.
NOTICE
■To prevent 12-volt battery discharge
Do not leave the lights on longer than
necessary when the engine is not running .
Turning on the high beam head-
lights
Follow me home system

193
4
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
Driving
Pull the lever toward you and release it
again to turn off the lights.
When any of the following conditions is
met, while the headlights (low beam)
are on, the cornering lights will addi-
tionally turn on and light up the direc-
tion of movement for the vehicle. This is
to ensure excellent visibility when
either driving at intersections or park-
ing at night.
 The steering wheel is operated
 The turn signal lever is operated
 The shift position is in R (both left
and right side cornering lights)
■Cornering light control
●The lights illuminate when the vehicle speed is approximately 30 km/h (19
mph) or less. However, the lights turn off when the vehicle speed increases to approximately 35 km/h (22 mph) or
more.
●After the lights remain illuminated for 30
minutes, they automatically turn off.
*:If equipped
1 Push the lever away from you with
the headlight switch in the or
position.
2 Press the Automatic High Beam
switch.
Cornering lights
Automatic High Beam*
The Automatic High Beam uses an
in-vehicle camera sensor to assess
the brightness of streetlights, the
lights of a vehicle ahead, etc., and
automatically turns the high beam
on or off as necessary.
WARNING
■Limitations of the Automatic High Beam
Do not rely on the Automatic High Beam. Always drive safely, taking care to observe your surroundings and turning
the high beam on or off manually if nec- essary.
■To prevent incorrect operation of the Automatic High Beam system
Do not overload the vehicle.
Activating the Automatic High
Beam system

194
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
The Automatic High Beam indicator will come on when the headlights are turned on automatically to indicate that the system
is active.
■High beam automatic turning on or off
conditions
●When all of the following conditions are
met, the high beam will be automatically turned on (after approximately 1 second):• Vehicle speed is above approximately 40
km/h (25 mph). • The area ahead of the vehicle is dark.• There are no vehicles ahead with head-
lights or tail lights turned on. • There are few streetlights on the road ahead.
●If any of the following conditions are met, the high beam will be automatically
turned off: • Vehicle speed drops below approxi-mately 30 km/h (19 mph).
• The area ahead of the vehicle is not dark. • Vehicles ahead have headlights or tail lights turned on.
• There are many streetlights on the road ahead.
■Camera sensor detection information
●The high beam may not be automatically turned off in the following situations:• When oncoming vehicles suddenly
appear from a curve • When the vehicle is cut in front of by another vehicle
• When vehicles ahead are hidden from sight due to repeated curves, road divid-ers or roadside trees
• When vehicles ahead appear from the faraway lane on wide road
• When vehicles ahead have no lights
●The high beam may be turned off if a
vehicle ahead that is using fog lights with- out using the headlights is detected.
●House lights, street lights, traffic signals, and illuminated billboards or signs may cause the high beam to switch to the low
beams, or the low beams to remain on.
●The following factors may affect the
amount of time taken to turn the high beam on or off:• The brightness of headlights, fog lights,
and tail lights of vehicles ahead • The movement and direction of vehicles ahead
• When a vehicle ahead only has opera- tional lights on one side• When a vehicle ahead is a two-wheeled
vehicle • The condition of the road (gradient, curve, condition of the road surface etc.)
• The number of passengers and amount of luggage
●The high beam may be turned on or off when the driver does not expect it.
●Bicycles or similar objects may not be detected.
●In the situations shown below, the system may not be able to accurately detect sur-
rounding brightness levels. This may cause the low beams to remain on or the high beams to cause problems for pedes-
trians, vehicles ahead or other parties. In these cases, manually switch between the high and low beams.
• In bad weather (rain, snow, fog, sand- storms etc.)• The windshield is obscured by fog, mist,
ice, dirt etc. • The windshield is cracked or damaged.• The camera sensor is deformed or dirty.
• Surrounding brightness levels are equal to those of headlights, tail lights or fog lights.
• Vehicles ahead have headlights or tail lights that are either switched off, dirty, changing color, or have improperly
adjusted aim. • When driving through an area of inter-mittently changing brightness and dark-

195
4
-$@-$I@0.@0.&@ &&

4-3. Operating the lights and wipers
Driving
ness. • When frequently and repeatedly driving ascending/descending roads, or roads
with rough, bumpy or uneven surfaces (such as stone-paved roads, gravel tracks etc.).
• When frequently and repeatedly taking curves or driving on a winding road.• There is a highly reflective object ahead
of the vehicle, such as a sign or a mirror. • The vehicle’s headlights are damaged or dirty.
• The vehicle is listing or titling, due to a flat tire, a trailer being towed etc.• The driver believes that the high beam
may be causing problems or distress to other drivers or pedestrians nearby.• The vehicle is used in a territory in which
vehicles travel on the opposite side of the road of the country for which the vehicle is approved, for example using a vehicle
designed for right-hand traffic in a left- hand traffic territory, or vice versa.
■Switching to low beam
Pull the lever to the original position.
The Automatic High Beam indicator will
turn off.
Push the lever away from you to activate
the Automatic High Beam system again.
■Switching to high beam
Press the Automatic High Beam
switch.
The Automatic High Beam indicator will
turn off and the high beam indicator will
turn on.
Press the switch to activate the Automatic
High Beam system again.
Turning the high beam on/off
manually

203
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
4-5.Us ing the driving suppo rt systems
*: If equipped
■PCS (Pre-Collision System)
 P.210
■LKA (Lane-Keeping Assist)
 P.218
■Automatic High Beam
 P.193
■RSA (Road Sign Assist)
 P.226
■Dynamic radar cruise control with
full-speed range
 P.229
The pre-collision system is equipped
with a sophisticated computer that will
record certain data, such as:
• Accelerator status
• Brake status
• Vehicle speed
• Operation status of the pre-collision
system functions
• Information (such as the distance
and relative speed between your
vehicle and the vehicle ahead or
other objects)
The pre-collision system does not
record conversations, sounds or pic-
tures.
 Data usage
Lexus may use the data recorded in this
computer to diagnose malfunctions, con-
duct research and development, and
improve quality.
Lexus will not disclose the recorded data to
a third party except:
Lexus Safety System+*
The Lexus Safety System+ consists
of the following drive assist systems
and contributes to a safe and com-
fortable driving experience:
Drive assist systems of Lexus
Safety System+
WARNING
■Lexus Safety System+
The Lexus Safety System+ is designed to
operate under the assumption that the driver will drive safely, and is designed to help reduce the impact to the occupants
and the vehicle in the case of a collision or assist the driver in normal driving con-ditions.
As there is a limit to the degree of recog- nition accuracy and control performance
that this system can provide, do not overly rely on this system. The driver is always responsible for paying attention
to the vehicle’s surroundings and driving safely.
Vehicle data recording

381
7
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
When trouble arises
Power was turned off due to the automatic power off function. Next time when starting the hybrid system, operate the hybrid system for approximately 5 minutes to recharge the 12-volt battery.
■If a message that indicates the need for the shift lever operation is shown
To prevent the shift lever from being operated incorrectly or the vehicle from moving unex- pectedly, a message that requires shifting the shift lever may be shown on the multi-informa-
tion display. In that case, follow the instru ction of the message and shift the shift lever.
■If “Front Camera Unavailable” or “Front Camera Vision Blocked Clean and Demist Windshield” is shown
The following systems may be suspended un til the problem shown in the message is resolved.
●PCS
●LKA
●Dynamic radar cruise cont rol with full-speed range
●Automatic High Beam
■If “Engine Stopped Steering Power Low” (LC500) or “Hybrid System Stopped Steer- ing Power Low” (LC500h) is shown
The steering wheel may become extremely heavy. If the steering wheel becomes heavier than usual when operating, hold firmly and operate using more force than usual.
■If “Warming Up Maximum Vehicle Speed: 110km/h” is shown (LC500h)
The transmission is being warmed up and the ve hicle is unable to be driven over 110 km/h (65 mph). Wait until the transmission warms up.
■If “Stop the vehicle in a safe place Shift to P position” is shown (LC500h)
There may be a malfunction in the hybrid system or the shift position may be shifted to N for a long time. Immediately stop the vehicle and contact any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
■If “Oil Maintenance Required Soon” is shown (LC500h)
The engine oil is scheduled to be changed. Check the engine oil, and change if necessary.
After changing the engine oil, the message should be reset. ( P.321)
■If “Engine Oil Level Low Add or Replace” is shown
The engine oil level is low. Check the level of engine oil, and add if necessary. This message
may appear if the vehicle is stopped on a slope. Move the vehicle to a level surface and check to see if the message disappears.
■If a message that indicates the need for referring to Owner’s Manual is shown
●If any of the following messages is shown on the multi-information display, follow the instructions.• “Engine Coolant Temp High” ( P.403, 403)
•“Battery low” ( P.392) • “Transmission Fluid Temp High” ( P.174, 180)
●If any of the following messages is shown on the multi-information display, it may indicate a malfunction. Have the vehicle inspected by any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer immediately.
• “Entry & Start System Malfunction”

441
-$@-$I@0.@0.&@ &&

Alphabetical index
Alphabetical index
A
A/C................................................................... 280
Air conditioning filter................................ 347
Automatic air conditioning system .. 280
Pollen removal mode ..............................285
ABS (Anti-lock Brake System) ..............262
Function .......................................................... 262
Warning light ...............................................369
Active rear wing ...........................................259
Adaptive Variable Suspension System
(AVS) .............................................................262
Airbag manual on-off system .....................46
Airbags ................................................................35
Airbag manual on-off system ................. 46
Airbag operating conditions................... 37
Airbag precautions for your child ........ 40
Correct driving posture ............................ 29
Curtain shield airbag operating condi-
tions .................................................................. 37
Curtain shield airbag precautions........ 40
General airbag precautions ................... 40
Locations of airbags.................................... 35
Modification and disposal of airbags . 42
Side airbag operating conditions ......... 37
Side airbag precautions ............................ 40
Side and curtain shield airbags operating
conditions ...................................................... 37
Side and curtain shield airbags precau-
tions .................................................................. 40
SRS airbags ..................................................... 35
SRS warning light.......................................369
Air conditioning filter.................................. 347
Air conditioning system............................ 280
Air conditioning filter................................ 347
Automatic air conditioning system .. 280
Pollen removal mode ..............................285
Alarm ................................................................... 76
Alarm .................................................................. 76
Warning buzzer ........................................ 368
Anchor brackets..................................... 49, 60
Antennas (smart entry & start system). 122
Anti-lock Brake System (ABS) ..............262
Function .......................................................... 262
Warning light .............................................. 369
Approach warning ......................................235
Automatic headlight leveling system.... 192
Automatic High Beam ................................ 193
Automatic light control system .................191
Automatic transmission.............................. 173
M mode ........................................................... 178
Paddle shift switches ....................... 177, 178
Snow mode..................................................... 177
Auxiliary net ...................................................293
Average fuel economy .................................94
Average vehicle speed.................................94
AVS (Adaptive Variable Suspension Sys-
tem).................................................................262
B
Back-up lights
Replacing light bulbs ............................... 355
Battery (12-volt battery) ............................325
Battery checking ........................................325
If the 12-volt battery is discharged ....392
Preparing and checking before winter
..........................................................................269
Replacing ...................................................... 398
Warning light .............................................. 368
Battery (traction battery) .............................65
Blind Spot Monitor (BSM) ...................... 248
Blind Spot Monitor function .................254
Rear Crossing Traffic Alert function 256
Brake
Brake hold ...................................................... 189
Fluid.................................................................... 418
Parking brake................................................ 187
Regenerative braking .................................63
Warning light .................................. 368, 373
Warning message .....................................379
Brake assist .....................................................262