instrument cluster LEXUS LS430 2003 Factory Owner's Manual

HINT:
See COMPONENTS

1.REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSY NO. 2
2.REMOVE INSTRUMENT PANEL GARNISH SUB-ASSY LH (See step 22 on REPLACEMENT
)
3.REMOVE INSTRUMENT PANEL FINISH PANEL (See step 26 on REPLACEMENT
)
4.REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSY NO. 1 (See step 16 on
REPLACEMENT
)
5.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSY NO. 1 (See step 19 on
REPLACEMENT
)
6.REMOVE CONSOLE PANEL SUB-ASSY UPPER (See step 38 on REPLACEMENT
)
7.REMOVE CONSOLE UPPER REAR PANEL SUB-ASSY (See step 39 on REPLACEMENT
)
8.REMOVE CONSOLE BOX CARPET (See step 40 on REPLACEMENT
)
9.REMOVE REAR CONSOLE ARMREST ASSY (See step 41 on REPLACEMENT
)
10.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER (See step 26 on
REPLACEMENT
)
11.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSY CENTER (See step 31 on
REPLACEMENT
)
12.REMOVE CONSOLE BOX (See step 42 on REPLACEMENT
)
13.SEPARATE OXYGEN SENSOR (See REPLACEMENT
)
14.REMOVE EXHAUST PIPE ASSY
a. Remove the 4 bolts, nuts and 2 gaskets from the exhaust manifold.
b. Remove the exhaust pipe assy.
15.REMOVE FRONT FLOOR HEAT INSULATOR NO. 1
a. Remove the 4 bolts and heat insulator No. 1.
16.REMOVE PROPELLER SHAFT HEAT INSULATOR
a. Remove the 2 bolts and heat insulator.
17.REMOVE PROPELLER W/CENTER BEARING SHAFT ASSY
a. Using SST, loosen the adjusting nut until it can be turned by hand.
SST 09922-10010
HINT:
Use 2 of the same t
ype of SST.

Fig. 31: Identifying Air Conditioning Panel Sub-Assy Components And Replacements
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REPLACEMENT
HINT:
Installation is in the reverse order of removal.
See COMPONENTS .
1.RESTORE SHIP MODE SETTING (W/ CD CHANGER) (See PRECAUTION
)
2.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER (See step 26 in
REPLACEMENT
)
3.REMOVE PANEL INSTRUMENT CLUSTER FINISH LOWER (See step 27 in
REPLACEMENT
)
4.REMOVE RADIO RECEIVER ASSEMBLY W/BRACKET (See step 4 in REPLACEMENT
)
5.CONFIRM SHIP MODE (W/ CD CHANGER) (See PRECAUTION
)
6.REMOVE TEMPERATURE CONTROL SWITCH ASSY
a. Using a screwdriver, release the 2 claws and remove the temperature control switch.
HINT:
Tape the screwdriver tip before use.
b. Employ the same manner described above to the other side.
c. Disconnect the connectors.

Fig. 6: Removing Instrument Panel Safety Pad Garnish Sub-Assy
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
14.REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER LOWER
a. Using a screwdriver, disengage the 2 claws and remove the instrument cluster finish panel center
lower.
HINT:
Tape up the screwdriver tip before use.

b. Disconnect the connector.
Fig. 7: Removing Instrument Cluster Finish Panel Center Lower

Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
15.REMOVE INSTRUMENT CLUSTER FINISH PANEL END
a. Using a screwdriver, disengage the 2 claws and the clip and remove the instrument cluster finish
panel center end.
HINT:
Tape up the screwdriver tip before use.
b. Disconnect the connector.
16.REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSY NO.1
a. Remove the 2 screws < N >.
b. Disengage the 2 clips and remove the instrument panel under cover sub-assy No.1.
c. Disconnect the connectors.

Fig. 16: Removing Instrument Panel Finish Panel Lower Center
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
27.REMOVE PANEL INSTRUMENT CLUSTER FINISH LOWER
a. Remove the 3 screws < N >.
b. Using a moulding remover, disengage the 2 clips and remove the panel instrument cluster finish
lower.
HINt:
Use a screwdriver if a moulding remover is not available.
tape up the screwdriver tip before use.
c. Disconnect the connectors.

Fig. 17: Removing Panel Instrument Cluster Finish Lower
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
28.REMOVE RADIO RECEIVER ASSY W/BRACKET (SEE REPLACEMENT
)
29.REMOVE TEMPERATURE CONTROL SWITCH ASSY
a. Using a moulding remover, disengage the 2 claws and remove the temperature control switch assy.
HINt:
Use a screwdriver if a moulding remover is not available.
tape up the screwdriver tip before use.
b. Disconnect the connector.

Fig. 19: Removing Instrument Cluster Finish Panel Sub-Assy Center (W/ Lexus Navigation
System)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
31.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSY CENTER (W/ LEXUS
NAVIGATION SYSTEM)
a. Remove the 4 bolts.
HINt:
Be careful not to drop the bolts when removing them from the display.
b. Using a moulding remover, disengage the 4 clips and remove the instrument cluster finish panel
sub-assy center.
HINt:
Remove the multi-display together with instrument cluster finish panel sub-assy center.
Use a screwdriver if a moulding remover is not available.
tape up the screwdriver tip before use.

c. Disconnect the connectors.
32.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSY CENTER (W/O LEXUS
NAVIGATION SYSTEM)
a. Remove the 2 bolts.
HINt:
Be careful not to drop the bolts when removing them from the display.
b. Using a moulding remover, disengage the 4 clips and remove the instrument cluster finish panel
sub-assy center.
Fig. 20: Removing Instrument Cluster Finish Panel Sub
-Assy Center (W/O Lexus Navigation
System)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
HINt:
Remove the multi-display together with instrument cluster finish panel sub-assy center.
Use a screwdriver if a moulding remover is not available.

Fig. 25: Removing Console Box
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
43.REMOVE INSTRUMENT CLUSTER FINISH PANEL
a. Remove the 2 clips.
b. Pull the instrument cluster finish panel away from the dash.
c. Disen
gage the 2 clips and remove the instrument cluster finish panel.

Fig. 26: Removing Instrument Cluster Finish Panel
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
44.REMOVE COMBINATION METER ASSY
a. Remove the 4 screws.
b. Disconnect the connector and remove the combination meter assy.