ignition LEXUS RX200T 2017 User Guide

1433-2. Opening, closing and locking the doors
3
Operation of each component
RX350/RX200t_EE_OM48F32E
For the front doors
Push down the inside lock button.
Close the door while pulling the door handle.
The door cannot be locked if the engine switch is in ACCESSORY or IGNITION
ON mode, or the electronic key is left insi de the vehicle. However, the key may not be detected correctly and the door may be locked.
For the rear doors
Push down the inside lock button.
Close the door.
The door cannot be locked if the engine switch is in ACCESSORY or IGNITION ON mode, or the electronic key is left insi de the vehicle. However, the key may not be detected correctly and the door may be locked.
The door cannot be opened from inside
the vehicle when the lock is set.
Unlock
Lock
These locks can be set to prevent chil-
dren from opening the rear doors. Push down on each rear door switch to lockboth rear doors.
The following functions can be set or canceled:
For instructions on customizing, refer to P. 741.
Locking the doors from the outside without a key
Rear door child-protector lock
1
2
1
2
1
2
Automatic door locking and unlocking systems
FunctionOperation
Speed linked door locking functionAll doors are automatically locked whenvehicle speed is approximately 20 km/h(12 mph) or higher.
Shift position linked door locking
function
All doors are automatically locked when
shifting the shift lever out of P.
Shift position linked door unlocking functionAll doors are automatically unlockedwhen shifting the shift lever to P.
Driver’s door linked door unlocking functionAll doors are automatically unlockedwhen driver’s door is opened.

1563-2. Opening, closing and locking the doors
RX350/RX200t_EE_OM48F32E
■Power back door operating conditions
If the following conditions are met with the power back door operation enabled ( P. 115), the power back door can be opened and closed automatically.
●The power back door is unlocked.
●When the engine switch is in IGNITION ON mode, the vehicle speed must be lower than 3 km/h (2 mph) and one of the following conditions must be met in addition to the above condition:
• The parking brake is engaged. • The brake pedal is depressed.• The shift lever is in P.
Touchless sensor (vehicles with a touchless power back door)
The power back door will open automatically when the touchless sensor operation is
enabled ( P. 115) and the following conditions are met:
●The power back door is fully closed.
●The electronic key is within the operational range (P. 168)
■Security feature
If the power back door is not opened within approximately 30 seconds after the vehicle
is unlocked, the security feature will automatically lock the doors again.
●A hand is held over the upper part of the rear emblem with fingers closed. (The upper part of
the rear emblem can also be touched.)
The power back door may also be operated by holding either of the following over the
upper part of the rear emblem. Make sure to hold it close enough to the rear emblem.
•A gloved hand
•An elbow

1633-2. Opening, closing and locking the doors
3
Operation of each component
RX350/RX200t_EE_OM48F32E
WARNING
■Back door closer
●Use caution when using the back door closer as it still operates when the power back door system is disabled.
■Power back door
Observe the following precautions when operating the power back door. Failure to do so may cause death or serious injury.
●Check the safety of the surrounding area to make sure there are no obstacles or any-thing that could cause any of your belongings to get caught.
●If anyone is in the vicinity, make sure they are safe and let them know that the power
back door is about to open or close.
●If the power back door system is disabled ( P. 115) while the power back door is operating, the power back door will stop operating. The power back door must then
be operated manually. Take extra care in th is situation, as the power back door may open or close suddenly.
●If the operating conditions of the power back door (P. 156) are no longer met, a
buzzer may sound and the power back door may stop opening or closing. The power back door must then be operated manually. Take extra care on an incline in this situa-tion, as the power back door may move suddenly.
●On an incline, the power back door may suddenly shut after it opens. Make sure thepower back door is fully open and secure.
●In the following situations, the power back door may detect an abnormality and auto-
matic operation may be stopped. In this case, the power back door must then be operated manually. Take extra care in this situation, as the stopped power back door may suddenly open or close, causing an accident.
• When the power back door contacts an obstacle • When the battery voltage suddenly drops, such as when the engine switch isturned to IGNITION ON mode or the engine is started during automatic opera-
tion
●In the event that the power back door is left
slightly open, the back door closer will auto- matically close it to the fully closed position. Ittakes several seconds before the back door
closer begins to operate. Be careful not to get fingers caught or anything else in the powerback door, as this may cause bone fractures
or other serious injuries.

1913-3. Adjusting the seats
3
Operation of each component
RX350/RX200t_EE_OM48F32E
■The rear seatbacks can be adjusted when (power seat)
■The rear seatbacks can be folded down when (power seat)
When all of the following conditions are met, a rear seat operation switch can be used to fold down the rear seatback:
●When using the rear seat operation switch (r ear seat): The rear door nearest to the seat
to be operated is open.
●When using the rear seat operation switch (luggage compartment): The back door is open.
●The other seat operation switch for the seat to be operated is not being pressed.
When the engine switch is in IGNITION ON mode, one of the following conditions must also be met in order for the power seat to be operated:
• The parking brake is engaged. • The brake pedal is depressed.• The shift lever is in P.
When the rear seatback is in a position within the range A shown in the illustration, the rear
seat operation switch (rear seat) can be used to adjust the rear seatback.
●When the engine switch is turned off or inACCESSORY mode
●When using the rear seat operation switch
(rear seat): The rear seatback is in a position within the range A shown in the illustration.
●When using the rear seat operation switch
(luggage compartment): The rear seatback is in a position within the range B shown in theillustration.
Most
upright
position
Most upright position

1923-3. Adjusting the seats
RX350/RX200t_EE_OM48F32E
■The rear seat seatbacks can be raised when (power seat)
When all of the following conditions are met, a rear seat operation switch can be used to return the rear seatback:
●When using the rear seat operation switch (luggage compartment): The back door is
open.
●The other seat operation switch for the seat to be operated is not being pressed.
When the engine switch is in IGNITION ON mode, one of the following conditions must
also be met in order for the power seat to be operated:
• The parking brake is engaged. • The brake pedal is depressed.
• The shift lever is in P.
■Fully reclining the rear seatback (power seat)
■Power seat operations (if equipped)
If a seat cover or seat cushion has been put on the seat, it may not operate properly. When folding down the rear seatback, make sure that there is nothing on the seat thatwould interfere with the operation.
■Rear seatback jam protection function (power seat)
When folding down or raising th e rear seatback, if an object is detected between the rear seatback and seat cushion, the rear seatb ack will stop and then move in the opposite direction slightly.
A buzzer will sound continuously when the rear seatback stops and intermittently when moving in the opposite direction.
●When the engine switch is turned off or inACCESSORY mode
●When using the rear seat operation switch(rear seat): The rear seatback is in a positionwithin the range A shown in the illustration.
●When using the rear seat operation switch(rear seat): The rear door nearest to the seat tobe operated is open.
Operate the rear seat operation switch (rear seat) to recline the rear seatback and stop itpartway. To set the rear seatback to the
rearmost position, press the button again.
Most
upright position

1953-3. Adjusting the seats
3
Operation of each component
RX350/RX200t_EE_OM48F32E
The seat and steering wheel are automatically adjusted to allow the driver to
enter and exit the vehicle easily.
When all of the following have been
performed, the seat and steering wheel
are automatically adjusted to a position
that allows driver to enter and exit the
vehicle easily.
• The shift lever has been shifted to P.
• The engine switch has been turned
off.
• The driver’s seat belt has been unfastened.
When any of the following has been performed, the seat and steering wheel
automatically return to their original positions.
• The engine switch has been turned to ACCESSORY mode or IGNITION
ON mode.
• The driver’s seat belt has been fastened.
■Operation of the power easy access system
When exiting the vehicle, the power easy access system may not operate if the seat is
already close to the rearmost position, etc.
■Customization
Some functions can be customized. ( P. 740)
Driving position memory
: If equipped
This feature automatically adjusts the front seats (on some models), steering
wheel and outside rear view mirrors to make entering and exiting the vehicle
easier or to suit your preferences.
Power easy access system (driver’s side only)

1963-3. Adjusting the seats
RX350/RX200t_EE_OM48F32E
Your preferred driving position (the position of the driver’s seat, steering wheel
and outside rear view mirrors) can be recorded and recalled by pressing a but-
ton.
Three different driving positions can be recorded into memory.
■Recording procedure
Check that the shift lever is in P.
Turn the engine switch to IGNITION ON mode.
Adjust the driver’s seat, steering wheel, and outside rear view mirrors to the
desired positions.
While pressing the “SET” button,
or within 3 seconds after the
“SET” button is pressed, press
button “1”, “2” or “3” until the
buzzer sounds.
If the selected button has already been preset, the previously recorded
position will be overwritten.
Vehicles with the driving position memory for the front passenger’s seat: To
record the position of the front passeng er’s seat, adjust the front passenger’s
seat to the desired position and perform step using the switches on the
front passenger’s side.
Driving position memory
1
2
3
4
4

1973-3. Adjusting the seats
3
Operation of each component
RX350/RX200t_EE_OM48F32E
■Recall procedure
Check that the shift lever is in P.
Turn the engine switch to IGNITION ON mode.
Press one of the buttons for the
driving position you want to recall
until the buzzer sounds.
■To stop the position recall operation part-way through
Perform any of the following:
●Press the “SET” button.
●Press button “1”, “2” or “3”.
●Operate any of the seat adjustment switches (only cancels seat position recall).
●Operate the tilt and telescopic steering control switch (only cancels steering wheel position recall).
■Seat positions that can be memorized ( P. 185)
The adjusted positions other than the position adjusted by lumbar support switch can be recorded.
■Operating the driving position memory after turning the engine switch off
Driver’s seat: Recorded seat positions can be activated up to 180 seconds after the driver’s door is
opened and another 60 seconds after it is closed again.
Front passenger’s seat: Recorded seat positions can be recalled up to 180 seconds after the front passenger’s
door is opened.
■In order to correctly use the driving position memory function
If a seat position is already in the furthest possible position and the seat is operated in the
same direction, the recorded position may be slightly different when it is recalled.
1
2
3

1983-3. Adjusting the seats
RX350/RX200t_EE_OM48F32E
Each electronic key (including a card key) can be registered to recall your pre-
ferred driving position.
■Registering procedure
Record your driving position to button “1”, “2” or “3” before performing the
following:
Carry only the key you want to register, and then close the driver’s door.
If 2 or more keys are in the vehicle, the driving position cannot be recorded
properly.
Check that the shift lever is in P.
Turn the engine switch to IGNITION ON mode.
Recall the driving position that you want to record.
While pressing the recalled but-
ton, press and hold the door lock
switch (either lock or unlock) until
the buzzer sounds.
If the button could not be registered, the buzzer sounds continuously for approximately 3 seconds.
■Recall procedure
Carry the electronic key that has been registered to the driving position,
and then unlock and open the driver’s door using the smart entry & start
system or wireless remote control.
The driving position will move to the recorded position (not including the steering
wheel). However, the seat will move to a posi tion slightly behind the recorded posi- tion in order to make entering the vehicle easier. If the driving position is in a position that has already been recorded, the seat and
outside rear view mirrors will not move.
Turn the engine switch to ACCESSORY mode or IGNITION ON mode,
or fasten a seat belt.
The seat and steering wheel will move to the recorded position.
Memory recall function (driver’s side only)
1
2
3
4
1
2

1993-3. Adjusting the seats
3
Operation of each component
RX350/RX200t_EE_OM48F32E
■Cancelation procedure
Carry only the key you want to cancel and then close the driver’s door.
If 2 or more keys are in the vehicle, the driving position cannot be canceled
properly.
Turn the engine switch to IGNITION ON mode.
While pressing the “SET” button, press and hold the door lock switch
(either lock or unlock) until the buzzer sounds twice.
If it button could not be canceled, the buzzer sounds continuously for approxi-
mately 3 seconds.
■Recalling the driving position us ing the memory recall function
●Different driving positions can be registered for each electronic key. Therefore, the driving position that is recalled may be different depending on the key being carried.
●If a door other than the driver’s door is unlocked with the smart entry & start system, the
driving position cannot be reca lled. In this case, press the driving position button which has been set.
■Customization
Some functions can be customized. ( P. 740)
WARNING
■Seat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear passenger or squeeze your body against the steering wheel.
1
2