ECU LEXUS RX200T 2017 Owner's Manual

651-2. Child safety
1
For safety and security
RX350/RX200t_EE_OM48F32E
Key of letters inserted in the above table:
X: Not suitable seat position for children in this mass group.
U: Suitable for “universal” category child restraint systems approved for use in
this mass group.
UF: Suitable for forward-facing “universal” category child restraint systems
approved for use in this mass group.
L: Suitable for “specific vehicles”, “restricted”, or “semi-universal”, category
child restraint system s approved for use in this mass group.
*1: Adjust the seatback angle to the most upright position. Move the front seat fully rear-
ward. If the passenger seat height can be adjusted, move it to the upper most position.
*2: If the head restraint interferes with your child restraint system, and the head restraint
can be removed, remove the head restraint. Otherwise, put the head restraint in the
upper most position.
When securing some types of child restrain t systems in second row seats, it may
not be possible to properly use the seat belts in positions next to the child
restraint without interfering with it or affecting seat belt effectiveness. Be sure
your seat belt fits snugly across your shoulder and low on your hips. If it does not,
or if it interferes with the child restraint, move to a different position. Failure to do
so may result in death or serious injury.
The child restraint systems mentioned in the table may not be available outside
the EU area.
●When installing a child restraint in the rear seats, adjust the front seat so that it
does not interfere with the child or child restraint system.
●When installing a child seat with support base, if the child seat interferes with
the seatback when latching it into the support base, adjust the seatback rear-
ward until there is no interference.
●When installing a forward-facing
child seat, if there is a gap between
the child seat and the seatback,
adjust the seatback angle until good
contact is achieved.

661-2. Child safety
RX350/RX200t_EE_OM48F32E
●If the seat belt shoulder anchor is ahead of the child seat belt guide, move the
seat cushion forward.
●When installing a junior seat, if the
child in your child restraint system is
in a very upright position, adjust the
seatback angle to the most comfort-
able position. And if the seat belt
shoulder anchor is ahead of the child
seat belt guide, move the seat cush-
ion forward.
◆Installing child restraint system using a seat belt
Install the child restraint system in accordance to the operation manual
enclosed with the child restraint system.
Adjust the seat
When using the front passenger seat
If installing the child restraint system to the front passenger seat is unavoid-
able, refer to P. 59 for the front passenger seat adjustment.
When using the rear seat
Adjust the seatback angle to the most uplight position.
Remove the head restraint if it interferes with your child restraint system.
( P. 200)
If the head restraint cannot be removed, raise it to the uppermost position.
Run the seat belt through the
child restraint system and insert
the plate into the buckle. Make
sure that the belt is not twisted.
Securely fix the seat belt to the
child restraint system in accor-
dance to the directions enclosed
with the child restraint system.
1
2
3

671-2. Child safety
1
For safety and security
RX350/RX200t_EE_OM48F32E
If your child restraint system is not
equipped with a lock-off (a seat
belt locking feature), secure the
child restraint system using a
locking clip.
After installing the child restraint system, rock it back and forth to ensure
that it is installed securely. ( P. 68)
◆Removing a child restraint system installed with a seat belt
Press the buckle release button and fully retract the seat belt.
When releasing the bu ckle, the child restraint system may spring up due to the rebound of the seat cushion. Release the buckle while holding down the child
restraint system.
Since the seat belt automatically reels itself , slowly return it to the stowing position.
■When installing a child restraint system
You may need a locking clip to install the child restraint system. Follow the instructions provided by the manufacturer of the system. If your child restraint system does not pro-
vide a locking clip, you can purchase the following item from any authorized Lexus dealer or repairer, or another duly qualified and equipped professional: Locking clip forchild restraint system
(Part No. 73119-22010)
4
5

681-2. Child safety
RX350/RX200t_EE_OM48F32E
WARNING
■When installing a child restraint system
Observe the following precautions. Failure to do so may result in death or serious injury.
●Do not allow children to play with the seat belt. If the seat belt becomes twistedaround a child’s neck, it may lead to choking or other serious injuries that could resultin death.
If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.
●Ensure that the belt and plate are securely locked and the seat belt is not twisted.
●Shake the child restraint system left and right, and forward and backward to ensure that it has been securely installed.
● After securing a child restrain t system, never adjust the seat.
●When a junior seat is installed, always ensure that the shoulder belt is positioned across the center of the child’s shoulder. Th e belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder.
●Follow all installation instructions provided by the child restraint system manufacturer.

691-2. Child safety
1
For safety and security
RX350/RX200t_EE_OM48F32E
■ISOFIX rigid anchors (ISOFIX child restraint system)
Lower anchors are provided for the
outboard rear seats. (Tags displaying
the location of the anchors are
attached to the seats.)
■Confirming the Mass group and Size class for ECE R44 ISOFIX corre-
sponding child restraint systems
Confirm the corresponding [Mass group] from the weight of the child
( P. 57)
(Ex. 1) When the weight is 12 kg (27 lb.), [Mass group 0+]
(Ex. 2) When the weight is 15 kg (34 lb.), [Mass group I]
Confirming Size class
Select the Size class corresponding to [Mass group] confirmed in step
from the [Child restraint system suitability table] ( P. 70)*.
(Ex. 1) When [Mass group 0+], the corresponding size class is [C], [D], [E].
(Ex. 2) When [Mass group I], the corresponding size class is [A], [B], [B1],
[C], [D].
*: However, listings that are marked with [X] cannot be selected, despite having the
corresponding size class in the suitability table of the [Seating position]. Also,
select the product designated by [Rec ommended Child Restraint Systems] (P.
70), if the listing is marked with [IL].
Child restraint system fixed with an ISOFIX rigid anchor
1
2
1

711-2. Child safety
1
For safety and security
RX350/RX200t_EE_OM48F32E
Mass groupsSize class
Seating position
Recommended Child Restraint
Systems
Front seatRear seat
Passenger seatOutboardCenter
Carrycot FXXX —GXXX
0 Up to 10 kg
(22 lb.)
EX IL X
“LEXUS MINI” “LEXUS MIDI” 0+
Up to 13 kg (28 lb.)
EX IL X
DX IL X
CX IL X
I
9 to 18 kg (20 to 39 lb.)
DX IL X —CX IL X
BX IUF*IL*X“LEXUS MIDI”
B1 X IUF*IL*X“LEXUS DUO+” “LEXUS MIDI”
AX IUF*
IL*X“LEXUS MIDI”

721-2. Child safety
RX350/RX200t_EE_OM48F32E
Key of letters inserted in the above table:
X: Not suitable seat position for ISOFIX child restraint systems in this mass
group and/or size class.
IUF: Suitable for ISOFIX forward-facing child restraint systems of “universal”
category approved for use in this mass group.
IL: Suitable for ISOFIX child restraint systems of the categories for “specific
vehicles”, “restricted”, or “semi-universal”, approved for use in this mass
group.
*: If the head restraint interferes with your child restraint system, and the head restraint
can be removed, remove the head restraint. Otherwise, put the head restraint in the
upper most position.
When securing some types of child restrain t systems in second row seats, it may
not be possible to properly use the seat belts in positions next to the child
restraint without interfering with it or affecting seat belt effectiveness. Be sure
your seat belt fits snugly across your shoulder and low on your hips. If it does not,
or if it interferes with the child restraint, move to a different position. Failure to do
so may result in death or serious injury.
The child restraint systems mentioned in the table may not be available outside
the EU area.
●When installing a child restraint in the rear seats, adjust the front seat so that it
does not interfere with the child or child restraint system.
●When using a “LEXUS MINI” or “LEXUS MIDI” adjust the support leg and
ISOFIX connectors as follows:
Lock the ISOFIX connectors
where number 3 can be seen.
Lock the support leg where 4
holes can be seen.
1
2

731-2. Child safety
1
For safety and security
RX350/RX200t_EE_OM48F32E
■Child restraint system suitability table
(Installed using i-Size [Child restraint system conforms with ECE R129])
If your child restraint system is of “i-Size” category, you can install it on the
positions mentioned by i-U in the table below. Child restraint system category
can be found in the child restraint system manual.
Key of letters inserted in the above table:
X: Not suitable for use with i-Size child restraint systems.
i-U: Suitable for i-Size “universal” child restraint systems forward and rearward
facing.
*: If the head restraint interferes with your child restraint system, and the head restraint
can be removed, remove the head restraint. Otherwise, put the head restraint in the
upper most position.
When securing some types of child restrain t systems in second row seats, it may
not be possible to properly use the seat belts in positions next to the child
restraint without interfering with it or affecting seat belt effectiveness. Be sure
your seat belt fits snugly across your shoulder and low on your hips. If it does not,
or if it interferes with the child restraint, move to a different position. Failure to do
so may result in death or serious injury.
When installing a child restraint in the re ar seats, adjust the front seat so that it
does not interfere with the child or child restraint system.
Seating position
Front seatRear seat
Passenger seatOutboardCenter
i-Size child
restraint systemsXi-U*X

741-2. Child safety
RX350/RX200t_EE_OM48F32E
■Installation with ISOFIX rigid anchor (ISOFIX child restraint system)
Install the child restraint system in accordance to the operation manual
enclosed with the child restraint system.
Adjust the seat
Adjust the seatback angle to the most uplight position.
Remove the head restraint if it interferes with your child restraint system.
( P. 200)
If the head restraint cannot be removed, raise it to the uppermost position.
Check the positions of the exclu-
sive fixing bars, and install the
child restraint system to the seat.
The bars are installed in the clear-
ance between the seat cushion and seatback.
After installing the child restraint system, rock it back and forth to ensure
that it is installed securely. ( P. 68)
1
2
3
WARNING
■When installing a child restraint system
Observe the following precautions. Failure to do so may result in death or serious injury.
●After securing a child restraint system, never adjust the seat.
●When using the lower anchors, be sure that there are no foreign objects around the anchors and that the seat belt is not caught behind the child restraint system.
●Follow all installation instructions provided by the child restraint system manufacturer.
4

751-2. Child safety
1
For safety and security
RX350/RX200t_EE_OM48F32E
■Anchor brackets (for top strap)
Anchor brackets are provided for the outboard rear seat.
Use anchor brackets when fixing the
top strap.
■Fixing the top strap to the anchor bracket
Install the child restraint system in accordance to the operation manual
enclosed with the child restraint system.
Remove the head restraint if it interferes with your child restraint system.
( P. 200)
If the head restraint cannot be removed, raise it to the uppermost position.
Open the anchor bracket cover,
latch the hook onto the anchor
bracket and tighten the top strap.
Make sure the top strap is securely
latched. ( P. 68) When installing th e child restraint system with the head restraint being
raised, be sure to have the top strap pass underneath the head restraint.
Using an anchor bracket (for top strap)
Top strap
Anchor brackets
1
Hook Top strap
2