brake light LEXUS RX300H 2017 Owner's Manual

3354-6. Driving tips
4
Driving
RC300h_EE(OM24740E)
◆When braking
Make sure to operate the brakes gently and in a timely manner. A greater
amount of electrical energy can be regenerated when slowing down.
◆Delays
Repeated acceleration and deceleration, as well as long waits at traffic lights,
will lead to bad fuel economy. Check traffic reports before leaving and avoid
delays as much as possible. When driving in a traffic jam, gently release the
brake pedal to allow the vehicle to move forward slightly while avoiding over-
use of the accelerator pedal. Doing so can help control excessive gasoline
consumption.
◆Highway driving
Control and maintain the vehicle at a constant speed. Before stopping at a toll
booth or similar, allow plenty of time to release the accelerator and gently
apply the brakes. A greater amount of electrical energy can be regenerated
when slowing down.
◆Air conditioning
Use the air conditioning only when necessary. Doing so can help reduce
excessive gasoline consumption.
In summer: When the ambient temperature is high, use the recirculated air
mode. Doing so will help to reduce the burden on the air conditioning system
and reduce fuel consumption as well.
In winter: Because the gasoline engine will not automatically cut out until it
and the interior of the vehicle are warm, it will consume fuel. Also, fuel con-
sumption can be improved by av oiding overuse of the heater.
◆Checking tire inflation pressure
Make sure to check the tire inflation pressure frequently. Improper tire infla-
tion pressure can cause poor fuel economy.
Also, as snow tires can cause large amounts of friction, their use on dry roads
can lead to poor fuel economy. Use ti res that are appropriate for the season.

3374-6. Driving tips
4
Driving
RC300h_EE(OM24740E)
●Use fluids that are appropriate to the prevailing outside temperatures.
•Engine oil
• Engine coolant
• Washer fluid
●Have a service technician inspect the condition of the 12-volt battery.
●Have the vehicle fitted with four snow tires or purchase a set of tire chains for
the rear tires.*
Ensure that all tires are the specified size and brand, and that chains match the size of the tires.
*: Tire chains cannot be mounted on vehicles with 19-inch tires.
Perform the following according to the driving conditions:
●Do not try to forcibly open a window or move a wiper that is frozen. Pour
warm water over the frozen area to melt the ice. Wipe away the water imme-
diately to prevent it from freezing.
●To ensure proper operation of the climate control system fan, remove any
snow that has accumulated on the air inlet vents in front of the windshield.
●Check for and remove any excess ice or snow that may have accumulated on
the exterior lights, vehicle’s roof, chassi s, around the tires or on the brakes.
●Remove any snow or mud from the bottom of your shoes before getting in the
vehicle.
Winter driving tips
Carry out the necessary preparations and inspections before driving the vehi-
cle in winter. Always drive the vehicle in a manner appropriate to the prevail-
ing weather conditions.
Preparation for winter
Before driving the vehicle

4637-1. Maintenance and care
7
Maintenance and care
RC300h_EE(OM24740E)
NOTICE
■To prevent paint deterioration and corrosion on the body and components (aluminum wheels etc.)
●Wash the vehicle immediately in the following cases:
• After driving near the sea coast • After driving on salted roads• If coal tar or tree sap is present on the paint surface
• If dead insects, insect droppings or bird droppings are present on the paint surface • After driving in an area contaminated wi th soot, oily smoke, mine dust, iron pow- der or chemical substances
• If the vehicle becomes heavily soiled with dust or mud • If liquids such as benzene and gaso line are spilled on the paint surface
●If the paint is chipped or scratched, have it repaired immediately.
●To prevent the wheels from corroding, remove any dirt and store in a place with low humidity when storing the wheels.
■Cleaning the exterior lights
●Wash carefully. Do not use organic subs tances or scrub with a hard brush. This may damage the surfaces of the lights.
●Do not apply wax to the surfaces of the lights.Wax may cause damage to the lenses.
■To prevent damage to the windshield wiper arms
When lifting the wiper arms away from the windshield, pull the driver side wiper arm upward first, and repeat for the passenger side. When returning the wipers to theiroriginal position, do so from the passenger side first.
■When using an automatic car wash (vehicle s with rain-sensing windshield wipers)
Set the wipers to the intermittent windshield wipers. ( P. 244) If AUTO mode is selected, the wipers may operate and the wiper blades may be dam-
aged.
■When using a high pressure car wash
●When washing the vehicle, do not spray the camera or its surrounding area directly
with a high pressure washer. Shock applied from high pressure water may cause the device to not operate normally.
●Do not bring the nozzle tip close to boots (rubber or resin manufactured cover), con-
nectors or the following parts. The parts may be damaged if they come into contact with high-pressure water.
• Traction related parts• Steering parts •Suspension parts • Brake parts

4707-3. Do-it-yourself maintenance
RC300h_EE(OM24740E)
WARNING
The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energize d. To avoid death or serious injury, observe the following precautions.
■When working on the engine compartment
●Make sure that the “ACCESSORY” or “IGNITION ON” on the multi-informationdisplay and the “READY” indicator are both off.
●Keep hands, clothing and tools away from the moving fan and engine drive belt.
●Be careful not to touch the engine, radiator, exhaust manifold, etc. right after drivingas they may be hot. Oil and other fluids may also be hot.
●Do not leave anything that may burn easily, such as paper and rags, in the enginecompartment.
●Do not smoke, cause sparks or expose an open flame to fuel. Fuel fumes are flamma-
ble.
●Be extremely cautious when working on the 12-volt battery. It contains poisonous and corrosive sulfuric acid.
●Take care because brake fluid can harm your hands or eyes and damage painted sur- faces. If fluid gets on your hands or in your eyes, flush the affected area with cleanwater immediately.
If you still experience discomfort, consult a doctor.
■When working near the electric cooling fans or radiator grille
Be sure the power switch is off.
With the power switch in ON mode, the electric cooling fans may automatically start to run if the air conditioning is on and/or the coolant temperature is high. ( P. 480)
■Safety glasses
Wear safety glasses to prevent flying or falling material, fluid spray, etc. from getting in your eyes.
NOTICE
■If you remove the air cleaner filter
Driving with the air cleaner filter removed may cause excessive engine wear due to dirt
in the air.
■If the fluid level is low or high
It is normal for the brake fluid level to go down slightly as the brake pads wear or when
the fluid level in the accumulator is high. If the reservoir needs frequent refillin g, it may indicate a serious problem.

5027-3. Do-it-yourself maintenance
RC300h_EE(OM24740E)
Raise the vehicle until the tire is
slightly raised off the ground.
Remove all the wheel nuts and the
tire.
When resting the tire on the ground,
place the tire so that the wheel design faces up to avoid scratching the wheelsurface.
4
5
WARNING
■Replacing a flat tire
●Do not touch the disc wheels or the area around the brakes immediately after thevehicle has been driven.
After the vehicle has been driven the disc wheels and the area around the brakes will be extremely hot. Touching these areas wi th hands, feet or other body parts while changing a tire, etc. may result in burns.
●Failure to follow these precautions could cause the wheel nuts to loosen and the tireto fall off, resulting in death or serious injury.
• Never use oil or grease on the wheel bolts or wheel nuts.
Oil and grease may cause the wheel nuts to be excessively tightened, leading to bolt or disc wheel damage. In addition, the oil or grease can cause the wheel nuts to loosen and the wheel may fall off, causing a serious accident. Remove any oil or
grease from the wheel bolts or wheel nuts. • Have the wheel nuts tightened with a torque wrench to 103 N•m (10.5 kgf•m,76 ft•lbf) as soon as possible after changing wheels.
• Do not attach a heavily damaged wheel or nament, as it may fly off the wheel while the vehicle is moving.• When installing a tire, only use wheel nuts that have been specifically designed for
that wheel. • If there are any cracks or deformations in the bolt screws, nut threads or bolt holesof the wheel, have the vehicle inspected by any authorized Lexus dealer or
repairer, or another duly qualif ied and equipped professional.

5378-2. Steps to take in an emergency
8
When trouble arises
RC300h_EE(OM24740E)
If a warning light turns on or a warning buzzer
sounds
Calmly perform the following actions if any of the warning lights comes on or
flashes. If a light comes on or flashes, but then goes off, this does not necessar-
ily indicate a malfunction in the system. However, if this continues to occur,
have the vehicle inspected by any authorized Lexus dealer or repairer, or
another duly qualified an d equipped professional.
Warning light and warning buzzer list
Warning lightWarning light/Details/Actions
Brake system warning light (warning buzzer) Indicates that:
• The brake fluid level is low; or • The brake system is malfunctioningThis light also comes on when the parking brake is not released. If
the light turns off after the parking brake is fully released the system is operating normally. Immediately stop the vehicle in a safe place and contact any
authorized Lexus dealer or repairer, or another duly qualified and equipped professional. Continuing to drive the vehicle maybe dangerous.
Brake system warning lightIndicates a malfunction in:• The regenerative braking system; or
• The electronically controlled brake system  Have the vehicle inspected by any authorized Lexus dealer or repairer, or another duly qualified and equipped professional
immediately.
Charging system warning light Indicates a malfunction in the vehicle’s charging system Immediately stop the vehicle in a safe place and contact any
authorized Lexus dealer or repairer, or another duly qualified and equipped professional.
Malfunction indicator lampIndicates a malfunction in:
• The hybrid system; • The emission control system (if equipped);• The electronic engine control system; or
• The electronic throttle control system  Have the vehicle inspected by any authorized Lexus dealer or repairer, or another duly qualified and equipped professional
immediately.

5388-2. Steps to take in an emergency
RC300h_EE(OM24740E)
SRS warning light Indicates a malfunction in:
• The SRS airbag system; or • The seat belt pretensioner system Have the vehicle inspected by any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional immediately.
ABS warning lightIndicates a malfunction in:
•The ABS; or • The brake assist system Have the vehicle inspected by any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional immediately.
Electric power steering system warning light (warning buzzer)Indicates a malfunction in the EPS (Electric Power Steering) sys-
tem  Have the vehicle inspected by any authorized Lexus dealer or repairer, or another duly qualified and equipped professional
immediately.
(Flashes) (If equipped)
Pre-crash safety system warning lightIndicates a malfunction in the PCS (Pre-Crash Safety system)The warning light will operate as follows, even when the system is
not malfunctioning: • The light will flash quickly when the system is operating.
( P. 311) • The light will turn on when the pre-crash safety system is dis- abled. ( P. 312)
• The light will turn on when th e VSC (Vehicle Stability Control) system is disabled. ( P. 307) • The light will flash when the sy stem cannot temporarily be used.
( P. 554)  Have the vehicle inspected by any authorized Lexus dealer or repairer, or another duly qualified and equipped professional
immediately.
Slip indicator Indicates a malfunction in:• The VSC (Vehicle Stability Control) system;
• The TRC (Traction Control) system; or • The hill-start assist control systemThe light will flash when the VSC or the TRC system is operating.
 Have the vehicle inspected by any authorized Lexus dealer or repairer, or another duly qualified and equipped professionalimmediately.
Warning lightWarning light/Details/Actions

5418-2. Steps to take in an emergency
8
When trouble arises
RC300h_EE(OM24740E)
■If the tire pressure warning light frequently comes on after blinking for 1 minute
If the tire pressure warning light frequently comes on after blinking for 1 minute when the power switch is turned to ON mode, have it checked by any authorized Lexus dealer or
repairer, or another duly qua lified and equipped professional.
■Warning buzzer
In some cases, the buzzer may not be heard due to being in a noisy location or audio
sound.
WARNING
■If both the ABS and the brake system warning lights remain on
Stop your vehicle in a safe place immediately and contact any authorized Lexus dealer or repairer, or another duly qualified and equipped professional. The vehicle will
become extremely unstable during braking, and the ABS system may fail, which could cause an accident resulting in death or serious injury.
■When the electric power steering system warning light comes on
The steering wheel may become extremely heavy. If the steering wheel becomes heavier than us ual when operating, hold firmly and oper- ate using more force than usual.
■If the tire pressure warning light comes on
Be sure to observe the following precautions. Failure to do so could cause a loss of vehicle control and result in death or serious injury.
●Stop your vehicle in a safe place as soon as possible. Adjust the tire inflation pressureimmediately.
●If the tire pressure warning light comes on even after tire inflation pressure adjust-
ment, it is probable that you have a flat tire. Check the tires. If a tire is flat, repair the flat tire by using emergency tire puncture repair kit.
●Avoid abrupt maneuvering and braking. If th e vehicle tires deteriorate, you could lose
control of the steering wheel or the brakes.
■If a blowout or sudden air leakage should occur
The tire pressure warning system may not activate immediately.
NOTICE
■To ensure the tire pressure warning system operates properly
Do not install tires with different specifications or makers, as the tire pressure warning system may not operate properly.

5528-2. Steps to take in an emergency
RC300h_EE(OM24740E)
Indicates a malfunction in the automatic headlight
leveling systemA buzzer also sounds.
 Have the vehicle inspected by any authorized Lexus
dealer or repairer, or another duly qualified and
equipped professional.
Indicates a malfunction in:
• The Automatic High Beam system (if equipped); or
• The LED headlight system A buzzer also sounds.
 Have the vehicle inspected by any authorized Lexus
dealer or repairer, or another duly qualified and
equipped professional.
Indicates that the accelerator and brake pedals are
being depressed simultaneously, and the brake override
system is operating. ( P. 207)
 Release the accelerator or brake pedal.
Indicates that the tire in flation pressure is low
 Check the tire inflation pressure, and adjust to the
appropriate level.
Warning messageDetails/Actions
(Flashes)

5548-2. Steps to take in an emergency
RC300h_EE(OM24740E)
Indicates that the engine oil is scheduled to be changed.
(The indicator will not work properly unless the message has been reset.) Check the engine oil, and change if necessary.
After changing the engine oil, the message should be reset.
Indicates that the engine oil should be changed. (Afterthe engine oil is changed and the message has been
reset.)  Check and change the engine oil, and oil filter by any authorized Lexus dealer or repairer, or another
duly qualified and equipped professional. After changing the engine oil, the message should bereset.
(If equipped)
Indicates that the Automatic High Beam switch ispressed while the headlights are in low beam.
 Turn the high beam on and press the Automatic High Beam switch again.
(If equipped)
Indicates that, since the VSC (Vehicle Stability Control)system was turned off, the pre-crash brake system oper-
ation is stopped Operation of the pre-crash brake assist is alsostopped.
 Turn the VSC on. (P. 307)
(If equipped)
Indicates that the PCS (Pre-Crash Safety system) is not currently functional because the grille cover or the sen- sor is dirty
 Check the grille cover and the sensor and clean them if they are dirty.
Warning messageDetails/Actions
(Flashes)