battery LEXUS RX450h 2015 Manual Online

5
When trouble arises
7835-2. Steps to take in an emergency
■
Stopping the hybrid system
Shift the shift lever to P and press the “POWER” switch as you normally do when
stopping the hybrid system.■
Replacing the key battery
As the above procedure is a temporary measure, it is recommended that the elec-
tronic key battery be replaced immediately when the battery is depleted.
(  P. 6 8 7 )■
Changing “POWER” switch modes
Within 10 seconds of the buzzer sounding, release the brake pedal and press the
“POWER” switch.
The hybrid system does not start and modes will be changed each time the switch is
pressed. (  P. 1 7 8 )

7845-2. Steps to take in an emergency
If the vehicle 12-volt battery is discharged The following procedures may be used to start the hybrid system if the vehi-
cle’s 12-volt battery is discharged.
You can also call your Lexus dealer or a qualified repair shop.
If you have a set of jumper (or booster) cables and a second vehicle
with a 12-volt battery, you can jump start your vehicle by following the
steps below.
Open the hood and remove the engine compartment covers.
(  P. 655)
Remove the fuse box cover and open the exclusive jump start-
ing terminal cover.
Connect the jumper cables according to the following procedure:
Connect a positive jumper cable clam p to the exclusive jump start-
ing terminal on your vehicle
Connect a positive jumper cable cl amp to the positive (+) battery
terminal on the second vehicle
Connect a negative cable clamp to the negative (-) battery terminal
on the second vehicle
Connect the clamp at the other end of the negative cable to a solid,
stationary, unpainted metallic point away from the exclusive jump
starting terminal and any moving part s, as shown in the illustration.STEP 1
STEP 2
STEP 3

5
When trouble arises
7855-2. Steps to take in an emergency
■
Starting the hybrid system when the 12-volt battery is discharged
The hybrid system cannot be started by push-starting.■
To prevent 12-volt battery discharge ●
Turn off the headlights and the audio sy stem while the hybrid system is off.●
Turn off any unnecessary electrical compon ents when the vehicle is running at a
low speed for an extended period, such as in heavy traffic.■
When the 12-volt battery is removed or discharged ●
The power back door must be initialized.
(  P. 8 3 7 )●
The hybrid system may not start. (
 P. 6 6 8 )
●
Make sure that the key is not inside th e vehicle when recharging or replacing
the 12-volt battery. The key may be locked in the vehicle if the alarm is activated.
(  P. 1 2 8 ) Start the engine of the second vehicle. Increase the engine
speed slightly and maintain that level for approximately 5 min-
utes to recharge the 12-volt battery of your vehicle.
Open and close any of the doors of your vehicle with the
“POWER” switch off.
Maintain the engine sp eed of the second ve hicle and start the
hybrid system of your vehicle by turning the “POWER” switch
to ON mode.
Make sure the “READY” indicat or comes on. If the indicator
does not come on, contact your Lexus dealer.
Once the hybrid system has st arted, remove the jumper cables
in the exact reverse order from which they were connected.
Once the hybrid system starts, have the vehicle inspected at your
Lexus dealer as soon as possible. STEP 4
STEP 5
STEP 6
STEP 7
STEP 8

7865-2. Steps to take in an emergency
■
Charging the 12-volt battery
The electricity stored in the 12-volt batter y will discharge gradually even when the
vehicle is not in use, due to natural discharge and the draining effects of certain
electrical appliances. If the vehicle is left for a long time, the 12-volt battery may dis-
charge, and the hybrid system may be un able to start. (The 12-volt battery
recharges automatically while the hybrid system is operating.)
CAUTION■
Avoiding 12-volt battery fires or explosions
Observe the following precautions to prevent accidentally igniting the flammable
gas that may be emitted from the 12-volt battery: ●
Make sure each jumper cable is connecte d to the correct terminal and that it is
not unintentionally in contact with an y other than the intended terminal.●
Do not allow the other end of the jumper cable connected to the “+” terminal to
come into contact with any other parts or metal surfaces in the area, such as
brackets or unpainted metal.●
Do not allow the + and - clamps of the jumper cables to come into contact with
each other.●
Do not smoke, use matches, cigarette lighters or allow open flame near the 12-
volt battery.■
12-volt battery precautions
The 12-volt battery contains poisonous and corrosive acidic electrolyte, while
related parts contain lead and lead compounds. Observe the following precautions
when handling the 12-volt battery: ●
When working with the 12-volt battery, always wear safety glasses and take care
not to allow any battery fluids (acid) to co me into contact with skin, clothing or the
vehicle body.
●
Do not lean over the 12-volt battery.
●
In the event that battery fluid comes into contact with the skin or eyes, immedi-
ately wash the affected area with water and seek medical attention.
Place a wet sponge or cloth over the affected area until medical attention can be
received.

5
When trouble arises
7875-2. Steps to take in an emergency
CAUTION●
Always wash your hands after handling the battery support, terminals, and other
battery-related parts.●
Do not allow children near the 12-volt battery.■
After recharging the 12-volt battery
Have the 12-volt battery inspected at your Lexus dealer as soon as possible.
If the 12-volt battery is deteriorating, co ntinued use may cause the 12-volt battery to
emit a malodorous gas, which may be de trimental to the health of passengers.■
When replacing the 12-volt battery
 P. 6 6 9
NOTICE■
When handling jumper cables
When connecting the jumper cables, ensure that they do not become entangled in
the cooling fans or belt.■
Avoiding accidental short-circuits
When connecting jumper cables, observe the following precautions: ●
Make sure each jumper cable is connected to the correct terminal.●
Do not allow the ends of the jumper cable used for the “+” terminals to come into
contact with any other parts or metal surfaces in the area, such as brackets or
unpainted metal.●
Do not allow the “+” and “-” terminals of the jumper cables to come into contact
with each other.■
Exclusive jump starting terminal precaution
The exclusive jump starting terminal is to be used when charging the 12-volt battery
from another vehicle in an emergency. It cannot be used to jump start another vehi-
cle.

8016-1. Specifications
6
Vehicle specifications Electric motor (Traction motor)
Front
Rear (AWD models)
Hybrid battery (Traction battery) Ty p e Permanent magnet synchronous motor
Maximum output 123 kW
Maximum torque 247 ft•lbf (335 N•m, 34.2 kgf•m)
Ty p e Permanent magnet synchronous motor
Maximum output 50 kW
Maximum torque 103 ft•lbf (139 N•m, 14.2 kgf•m)
Ty p e Nickel-metal hydride battery
Vo l t a g e 9.6 V/m o d u l e
Capacity 6.5 Ah (3HR)
Quantity 30 modules
Overall voltage 288 V

8056-1. Specifications
6
Vehicle specifications Electrical system
Hybrid Transaxle
* : The fluid capacity is a reference quantity. If replacement is necessary, contact
your Lexus dealer.12-volt battery
Open voltage* at
68  F (20  C): 12.6  
12.8 V Fully charged
12.2  
12.4 V Half charged
11.8  
12.0 V Discharged
(*: Voltage checked 20 minutes after the hybrid sys-
tem and all the lights are turned off)
Charging rates 5 A max.
Fluid capacity*
Front 4.9 qt. (4.6 L, 4.0 Imp. qt.)
Rear (AWD models) 1.9 qt. (1.8 L, 1.6 Imp. qt.)
Fluid type Toyota Genuine ATF WS
NOTICE■
Hybrid transmission fluid type
Using transmission fluid other than “Toyota Genuine ATF WS” may ultimately dam-
age the hybrid transmission of your vehicle.

8206-1. Specifications
Tire related term Meaning
Occupant distribution Distribution of occupants in a vehicle as specified in
the third column of Table 1
* below
Production options
weight The combined weight of installed regular production
options weighing over 5 lb. (2.3 kg) in excess of the
standard items which they replace, not previously
considered in curb weight or accessory weight,
including heavy duty brakes, ride levelers, roof rack,
heavy duty 12-volt battery, and special trim
Rim A metal support for a tire or a tire and tube assembly
upon which the tire beads are seated
Rim diameter
(Wheel diameter) Nominal diameter of the bead seat
Rim size designation Rim diameter and width
Rim type designation The industry manufacturer's designation for a rim by
style or code
Rim width Nominal distance between rim flanges
Vehicle capacity weight
(Total load capacity) The rated cargo and luggage load plus 150 lb. (68
kg) times the vehicle's designated seating capacity
Vehicle maximum load on
the tire The load on an individual tire that is determined by
distributing to each axle its share of the maximum
loaded vehicle weight, and dividing by two
Vehicle normal load on
the tire The load on an individual tire that is determined by
distributing to each axle its share of curb weight,
accessory weight, and normal occupant weight (dis-
tributed in accordance with Table 1
* below), and
dividing by two
We a t h e r s i d e The surface area of the rim not covered by the
inflated tire

8366-2. Customization
Multi-information display (  P. 206)
Settings that can be changed usin g the multi-information switchesAvailable languages English, French and Spanish
Available units miles (MPG), km (km/L), km (L/100 km)■
In the following situations, customize mo de will automatically be turned off.●
A warning message appears after the customize mode screen is displayed.●
The “POWER” switch is turned off.●
The vehicle begins to move while the customize mode screen is displayed.
CAUTION■
Cautions during customization
As the hybrid system needs to be operatin g during customization, ensure that the
vehicle is parked in a place with adequate ventilation. In a closed area such as a
garage, exhaust gases including harmful carbon monoxide (CO) may collect and
enter the vehicle. This may lead to death or a serious health hazard.
NOTICE■
During customization
To prevent 12-volt battery discharge, ensure that the hybrid system is operating
while customizing features.

8376
Vehicle specifications 6-3. Initialization
Items to initialize Item When to initialize Reference
Power back door • After reconnecting or changing the
12-volt battery
• After changing a fuse P. 7 5
Maintenance data
(U.S.A. only) After the maintenance is performed P. 6 4 1
Tire pressure warning
system • When rotating the tires
• When changing tire pressure (such
as when changing traveling speed,
load weight, etc.)
• When changing the tire size P. 6 7 1The following items must be initialized for normal system operation in cases
such as after the 12-volt battery is reconnected, or maintenance is per-
formed on the vehicle.