ect LEXUS SC300 1991 Service Repair Manual

PRECAUTIONS
Take care to observe the following precautions when performing inspection\
s or removal and replacement
of body electrical related parts.
1. SRS AIR±BAG SYSTEM

Work must be started approx. 20 seconds after the ignition is set to the Loc\
k position and the negative
(±) terminal cable is disconnected from the battery. (See page AB±2)

When disconnecting any of the connectors in the SRS AIR±BAG system, be su\
re to Lock the ignition
switch and disconnect the battery negative (±) terminal first. Since the connectors are twin \
lock type
connectors, disconnect the connectors only after releasing the first stage lock.

When connecting SRS AIR±BAG system connectors, be sure to lock them secur\
ely. (If the connectors
are not locked securely, the system may not operate when needed.)

Always store the steering wheel pad with the pad surface facing upward. (Stor\
ing the pad with its
metallic surface up may lead to a serious accident if the air bag inflates for s\
ome reason.)

When installing the spiral cable, be sure the vehicle is in the straight ahe\
ad condition and confirm that
the spiral cable is in the neutral position when it is installed. (See pag\
e BE±40)

INFORMATION LABELS (NOTICE) are attached to the periphery of the air bag componen\
ts. Follow
the NOTICE.
2. MICRO COMPUTER PRESET DRIVING POSITION SYSTEM
Power Seat Control System
Power Mirror Control System
Power Tilt and Telescopic Steering System

If the battery negative (±) terminal is disconnected, the preset driv\
ing positions stored in memory are
erased, so be sure to note the positions and reset them after the battery termi\
nal is reconnected.
3. AUDIO SYSTEM

If the battery negative (±) terminal is disconnected, the preset AM, F\
M 1 and FM 2 stations stored in
memory are erased, so be sure to note the stations and reset them after the battery terminal is
reconnected.

If the battery negative (±) terminal is disconnected, the ºANTI±\
THEFT SYSTEMº will operate when
the terminal is reconnected, but the radio, tape player and CD player will \
not operate. Be sure to input
the correct ID number so that the radio, tape player and CD player can be o\
perated again.
±
BODY ELECTRICAL SYSTEM PrecautionsBE±7
WhereEverybodyKnowsYourName

PREPARATION
SST (SPECIAL SERVICE TOOLS)
IllustrationPart No.Part NameNote
09213±31021
Crankshaft Pulley
Puller
For removing steering wheel
RECOMMENDED TOOLS
IllustrationPart No.Part NameNote
09082±00015TOYOTA
Electrical Tester
09041±0030Torx Driver
T30
For removing and installing steering wheel pad and
power window motor
09042±00010Torx Socket
T30For removing and installing steering wheel pad and
power window motor
EQUIPMENT
Part NameNote
Voltmeter
Ammeter
Ohmmeter
Test lead
ThermometerWater temperature sender gauge, Engine oil level, Warning switch, Seat heater
SyphonBrake fluid level warning switch
Oil bathEngine oil level warning switch
Bulb (1.4 W)Coolant level warning ECU
Bulb (3.4 W)Fuel sender, gauge, Seat belt warning relay
Bulb (21 W)Turn signal flasher relay
Dry cell batteryFuel sender gauge
Heat lightSeat heater
Hexagon wrench (6 mm)Power seat
BE±8±
BODY ELECTRICAL SYSTEM Preparation
WhereEverybodyKnowsYourName

EQUIPMENT (Cont'd)
PartNote
Torque wrench
Clip removerFor removing cowl louver
Masking tapeRear window defogger wire
Tim foilRear window defogger wire
SSM (SPECIAL SERVICE MATERIALS)
Part NamePart No.Use etc.
Adhesive 1324,
Three bond 1324 or equivalent08833±00070Power seat housing set nut, Power seat slide and vertical
motor set screw
Adhesive 1344,
Three bond 1344,
Loctite 242 or equivalent
08833±00080Low oil pressure warning switch Water temperature
sender gauge
Dupont paste No. 4817±Rear window defogger wire
±
BODY ELECTRICAL SYSTEM PreparationBE±9
WhereEverybodyKnowsYourName

POWER SOURCE
Parts Location
BE±10±
BODY ELECTRICAL SYSTEM Power Source
WhereEverybodyKnowsYourName

Parts Location (Cont'd)
±
BODY ELECTRICAL SYSTEM Power SourceBE±11
WhereEverybodyKnowsYourName

Parts Location (Cont'd)
BE±12±
BODY ELECTRICAL SYSTEM Power Source
WhereEverybodyKnowsYourName

Parts Location (Cont'd)
±
BODY ELECTRICAL SYSTEM Power SourceBE±13
WhereEverybodyKnowsYourName

Parts Location (Cont'd)
BE±14±
BODY ELECTRICAL SYSTEM Power Source
WhereEverybodyKnowsYourName

Wiring Diagram
±
BODY ELECTRICAL SYSTEM Power SourceBE±15
WhereEverybodyKnowsYourName

Replacement of Relays
REPLACEMENT OF RELAY IN RELAY
BLOCK NO. 1, NO. 4 and NO. 5
1. REMOVE FOLLOWING PARTS:(See page BO±112)
(a) No. 1 under cover.
(b) Door scuff plate.
(c) Floor carpet.
2. REMOVAL AND INSTALLATION OF RELAY
(a) Remove the junction block No. 1 set bolts.
(b) Disconnect connectors.
(c) Separate the relay block No. 4 and No. 5 from the junction block No. 1.
(d) For installation follow the removal procedure in reverse.
Replacement of Relay Block No. 2
(A)
REPLACEMENT OF RELAY BLOCK NO. 2
(A) IN RELAY BLOCK NO. 2
1. REMOVE RELAY BLOCK NO. 2 (A)
(a) Remove the battery. CAUTION: Work must be started after approx. 20 se-
conds or longer from the time the ignition switch is
turned to the ºLOCKº position and negative (±) terminal
cable is disconnected from the battery.
(b) Remove the relay block No. 2 cover.
(c) Pry loose two locking lugs and remove the nut.
2. INSTALL RELAY BLOCK NO. 2 (A) For installation follow removal procedure in reverse.
BE±16
±
BODY ELECTRICAL SYSTEM Power Source
WhereEverybodyKnowsYourName