LEXUS SC400 1991 Service Repair Manual

±
1UZ±FE ENGINE ENGINE MECHANICALEG±45
WhereEverybodyKnowsYourName

EG21P±02
TIMING BELT REMOVAL
(See Components for Removal and Installation)
1. REMOVE BATTERY CAUTION: Work must be started after 90 seconds from
the time the ignition switch is turned to the ªLOCKº posi-
tion and the negative (±) terminal cable is disconnected
from the battery.
2. REMOVE ENGINE UNDER COVER
3. DRAIN ENGINE COOLANT
4. REMOVE DRIVE BELT
Loosen the drive belt tension by turning the drive belt tension-
er counterclockwise, and remove the drive belt.
HINT: The pulley bolt for the drive belt tensioner has a left±
hand thread.
5. REMOVE RADIATOR RESERVOIR TANK
(a) Disconnect the coolant level sensor connector.
(b) Disconnect the following hoses: (1) Reservoir hose from water inlet housing
(2) Reservoir hose from radiator
(c) Remove the 2 bolts and reservoir tank bracket.
(d) Remove the bolt holding the reservoir tank to the radiator.
(e) Disconnect the reservoir tank from the reservoir tank bracket,
and remove the reservoir tank.
6. REMOVE RADIATOR ASSEMBLY
(a) Disconnect the ECT sensor connector (for cooling fan).
(b) Disconnect the ECT sensor wire clamp from the radiator fan shroud.
EG±46
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

(c) Disconnect the following hoses:(1) 2 oil cooler hoses (for cooling fan) from pipes
(2) 2 radiator hoses
(3) 2 oil cooler hoses (for transmission) from radiator
HINT: Plug the hose ends.
(4) Suction hose from hydraulic pump
(5) Pressure hose from hydraulic pump
(d) Remove the 2 bolts, screw and upper radiator support. Remove the 2 upper radiator supports.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±47
WhereEverybodyKnowsYourName

(e) Slightly lift the radiator, and disconnect the 2 oil cooler hoses(for cooling fan) from the hose clamp on the radiator fan
shroud.
(f) Remove the radiator assembly.
(g) Remove the 2 lower radiator supports from the radiator.
7. DISCONNECT AIR CONDITIONING (A/C) COMPRESSOR
FROM ENGINE
(a) Disconnect the A/C compressor connector.
(b) Remove the nut, and disconnect the ground cable from the
A/C compressor stay.
(c) Remove the bolt and A/C compressor stay.
(d) Remove the 2 bolts, and disconnect the A/C compressor from the engine.
HINT: Put aside the A/C compressor, and suspend it.
8. REMOVE INTAKE AIR CONNECTOR
(a) Disconnect the following hoses: (1) Air hose from IAC valve
(2) Air hose (from air control valve on PS pump) from intake
air connector
(b) Remove the bolt holding the intake air connector to the cylinder head cover.
(c) Loosen the 2 hose clamps.
(d) Disconnect the intake air connector from the throttle body
and air cleaner hose, and remove the intake air connector.
EG±48
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

9. REMOVE LH IGNITION COIL
(a) Disconnect the following connectors and cord:(1) Ignition coil connector
(2) Noise filter connector
(3) High±tension cord
(b) Remove the 2 bolts and ignition coil.
10. REMOVE UPPER HIGH±TENSION CORD COVER
(a) Remove the 2 bolts.
(b) Disconnect the front side claw groove of the upper cord cover
from the claw of lower cord cover, and remove the upper cord
cover.
11. REMOVE RH ENGINE WIRE COVER Remove the bolt and engine wire cover.
12. REMOVE LH ENGINE WIRE COVER Remove the 2 bolts and engine wire cover.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±49
WhereEverybodyKnowsYourName

20. REMOVE DISTRIBUTOR CAPSLoosen the 3 bolts, and remove the distributor cap.
Remove the 2 distributor caps.
HINT: Arrange the distributor caps (RH side and LH side).
21. REMOVE DISTRIBUTOR ROTORS Loosen the 2 bolts, and remove the distributor rotor.
Remove the 2 distributor rotors.
HINT: Arrange the distributor rotors (RH side and LH side).
22. REMOVE DISTRIBUTOR HOUSINGS
(a) RH Distributor Housing: Disconnect the camshaft position sensor connector.
(b) Remove the 3 bolts and distributor housing. Remove the 2 distributor housings.
23. REMOVE GENERATOR
(a) Disconnect the generator connector.
(b) Remove the cap and nut, and disconnect the generator wire.
(c) Remove the bolt, and disconnect the transmission oil cooler pipe bracket from the generator.
(d) Remove the nut and generator.
24. REMOVE DRIVE BELT TENSIONER Remove the bolt, 2 nuts and belt tensioner.
EG±52
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

25. REMOVE SPARK PLUGSUsing a 16 mm plug wrench, remove the 8 spark plugs.
26. IF RE±USING TIMING BELT, CHECK INSTALLATION MARKS ON TIMING BELT
Check that there are 4 installation marks on the timing belt by
turning the crankshaft pulley as shown in the illustration.
HINT: If the installation marks have disappeared, place a new
installation mark on the timing belt before removing each
part.
27. SET NO.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley and align its groove with timing mark ª0º of the No.1 timing belt cover.
(b) Check that the timing marks of the camshaft timing pulleys and timing belt rear plates aligned.
If not, turn the crankshaft 1 revolution (360 5).
28. REMOVE TIMING BELT TENSIONER HINT:
wWhen re±using timing belt:
If the installation marks have disappeared, before re-
move the timing belt, place new installation marks on
the timing belt to match the timing marks of the camshaft
timing pulleys, and place the a new installation mark on
the timing belt to match the end of the hydraulic pump.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±53
WhereEverybodyKnowsYourName

wWhen replacing timing belt tensioner only:
To avoid meshing of the timing pulley and timing belt,
secure one of them with string. And place matchmarks
on the timing belt and RH camshaft timing pulley.
Alternately loosen the 2 bolts, and remove them, the belt ten-
sioner and dust boot.
29. DISCONNECT TIMING BELT FROM CAMSHAFT TIMING PULLEYS
(a) Using SST, loosen the tension spring between the LH and RH
camshaft timing pulleys by slightly turning the LH camshaft
timing pulley clockwise.
SST 09278±54012
(b) Disconnect the timing belt from the camshaft timing pulleys.
30. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt and timing pulley. Remove the 2
timing pulleys.
SST 09278±54012
EG±54
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName