LEXUS SC400 1991 Service Repair Manual

±
STEERING POWER STEERINGSR±111
WhereEverybodyKnowsYourName

RECOMMENDED TOOLS
SR0FW±03
LUBRICANT
SR015±05
 Item Capacity Classification
 
Power steering fluid
1 0 liters (1 1 US qts 0 9 lmpqts)ATF DEXRON[II 

Total1.0 liters (1.1 US qts, 0.9 lmp.qts)AT F DEXRON[ II
EQUIPMENT
SR0FX±01\
 
\

\
Caliper gauge
 

Power steering pump
\
 \
Dial indicatorSteering rack
\
 
\

\
MicrometerPower steering pump
\
 
\

\

Oil pressure gauge
\
 \
Torque wrench
\
 
\

\

Vacuum gaugeGear housing
SSM (SPECIAL SERVICE MATERIALS)
SR0FY±01 08833±00080 Adhesive 1344, Rack housing cap  THREE BOND 1344, Rack guide spring cap
 


 


LOCTITE 242 or equivalent 


Rack guide spring cap lock nut
SR±112±
STEERING POWER STEERING
WhereEverybodyKnowsYourName

ON±VEHICLE INSPECTION
CHECK IDLE±UP
SR0FZ±04
1. WARM UP ENGINE
2. TURN AIR CONDITIONER SWITCH OFF
3. CHECK IDLE±UP
(a) Fully turn the steering wheel.
(b) Check that the engine rpm decreases when the air controlvalve hose is pinched.
(c) Check that the engine rpm increases when the air control valve hose is released.
FLUID LEVEL CHECK
SR0G0±03
1. KEEP VEHICLE LEVEL
2. BOOST FLUID TEMPERATUREWith the engine idling at 1,000 rpm or less, turn the steering
wheel from lock to lock several times to boost fluid tempera-
ture.
Fluid temperature:
805C (176 5F)
3. STOP ENGINE
4. CHECK FOR FOAMING OR EMULSIFICATION
HINT: Foaming and emulsification indicate either the exis-
tence of air in the system or that the fluid level is too low.
5. CHECK FLUID LEVEL IN OIL RESERVOIR Check the fluid level and add fluid if necessary.
Fluid:
ATF DEXRON
[ II
HINT: Check that the fluid level is within the HOT LEVEL of
the dipstick of the reservoir cap. If the fluid is cold, check that
it is within the COLD LEVEL of the dipstick.
±
STEERING POWER STEERINGSR±113
WhereEverybodyKnowsYourName

POWER STEERING FLUID
REPLACEMENT
SR0G1±04
1. JACK UP FRONT OF VEHICLE AND SUPPORT IT WITHSTANDS
2. REMOVE FLUID RETURN HOSE FROM OIL RESERVOIR AND DRAIN FLUID INTO CONTAINER
NOTICE: Take care not to spill fluid on the drive belt.
3. TURN STEERING WHEEL FROM LOCK TO LOCK WHILEDRAINING FLUID
4. FILL OIL RESERVOIR WITH FRESH FLUID
Fluid: ATF DEXRON
[ II
5. START ENGINE AND RUN IT AT 1,000 RPMAfter 1 or 2 seconds, fluid will begin to discharge from the re-
turn hose. Stop the engine immediately at this time.
NOTICE: Take care that some fluid remains left in the oil reser-
voir.
6. REPEAT STEPS 4 AND 5 FOUR OR FIVE TIMES UNTIL THERE IS NO MORE AIR IN FLUID
7. CONNECT RETURN HOSE TO OIL RESERVOIR
8. BLEED POWER STEERING SYSTEM (See page SR±115)
SR±114
±
STEERING POWER STEERING
WhereEverybodyKnowsYourName

POWER STEERING SYSTEM BLEEDING
SR0G2±04
1. CHECK FLUID LEVEL IN OIL RESERVOIRCheck the fluid level and add fluid if necessary.
Fluid:
ATF DEXRON
[ II
HINT: Check that the fluid level is within the HOT LEVEL of
the dipstick of the reservoir cap. If the fluid is cold, check that
it is within the COLD LEVEL of the dipstick.
2. START ENGINE AND TURN STEERING WHEEL FROM LOCK TO LOCK 3 OR 4 TIMES
With the engine speed below 1,000 rpm, turn the steering
wheel to left or right full lock and keep it there for 2±3 se-
conds, then turn the wheel to the opposite full lock and keep
it there for 2±3 seconds.
3. CHECK THAT FLUID IN OIL RESERVOIR IS NOT FOAMY OR CLOUDY AND DOES NOT RISE OVER MAXIMUM
WHEN ENGINE IS STOPPED
Measure the fluid level with the engine running. Stop the en-
gine and measure the fluid level.
Maximum rise:
5 mm (0.20 in.)
If a problem is found, repeat fluid replacement on page
SR±114. Rep air the PS if the problem persists.
OIL PRESSURE CHECK
SR0G3±03
1. CONNECT PRESSURE GAUGE
(a) Using SST, disconnect the pressure line joint.SC 400:
SST 09631±22020
±
STEERING POWER STEERINGSR±115
WhereEverybodyKnowsYourName

(b) Connect the gauge side of the pressure gauge to the PSpump side, and the valve side to the gear housing side.
2. BLEED POWER STEERING SYSTEM (See page SR±115)
3. START ENGINE AND RUN IT AT IDLE
4. BOOST FLUID TEMPERATURE With the engine idling at 1,000 rpm or less, turn the steering
wheel from lock to lock several times to boost fluid tempera-
ture.
Fluid temperature: 80
C (176
F)
5. CHECK FLUID PRESSURE READING WITH VALVE
CLOSED
Close the pressure gauge valve and observe the reading on
the gauge.
Minimum pressure:
7,355 kPa (75 kgf/cm
2, 1,067 psi)
NOTICE:
w Do not keep the valve closed for more than 10 seconds.
w Do not let the fluid temperature become too high.
If pressure is low, repair or replace the PS vane pump.
6. OPEN VALVE FULLY
7. CHECK AND RECORD PRESSURE READING AT 1,000
RPM
8. CHECK AND RECORD PRESSURE READING AT 3,000 RPM
Check that the pressure difference between the 1,000 rpm
and 3,000 rpm checks is less than 490 kPa (5 kgf/cm
2, 71
psi). If the difference is excessive, repair or replace the flow
control valve of the PS vane pump.
NOTICE: Do not operate the steering wheel.
SR±116±
STEERING POWER STEERING
WhereEverybodyKnowsYourName

9. CHECK PRESSURE READING WITH STEERING WHEELTURNED TO FULL LOCK
Be sure the pressure gauge valve is fully opened and the en-
gine idling.
Minimum pressure:
7,355 kPa (75 kgf/cm
2, 1,067 psi)
NOTICE:
w Do not maintain lock position for more than 10 seconds.
w Do not let the fluid temperature become too high.
If pressure is low, the gear housing has an internal leak and
must be repaired or replaced.
10. MEASURE STEERING EFFORT
(a) Center the steering wheel and run the engine at idle.
(b) Using a spring scale, measure the steering effort in both directions.
Maximum steering effort:
40 N (4.1 kgf, 9.0 lbf)
If steering effort is excessive, repair the power steering unit.
HINT: Be sure to consider the tire type, pressure and contact
surface before making your diagnosis.
(c) Disconnect the solenoid connector.
(d) Using a spring scale, measure the steering effort in both directions.
(Reference)
Maximum steering effort:
76 N (7.7 kgf, 17.0 lbf)
If steering effort is not heavier than (b), check solenoid.
HINT: Be sure to consider the tire type, pressure and contact
surface before making your diagnosis.
±
STEERING POWER STEERINGSR±117
WhereEverybodyKnowsYourName

POWER STEERING PUMP
(SC400)
POWER STEERING PUMP REMOVAL
AND INSTALLATION
SR0G4±01
Remove and install the parts, as shown.
MAIN POINTS OF REMOVAL AND
INSTALLATION
1. REMOVE DRIVE BELTLoosen the drive belt tension by turning the drive belt tension-
er counterclockwise, and remove the drive belt.
SR±118
±
STEERING POWER STEERING
WhereEverybodyKnowsYourName

2. INSTALL PUMP ASSEMBLYTorque the bolts and nut on the pump assembly in the order
shown.
Torque:
Bolt 39 N Vm (400 kgf Vcm, 29 ft Vlbf)
Nut 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
3. CONNECT PRESSURE TUBE
Make sure the stopper is touching the pump housing, as
shown, then torque the union bolt.
Torque: 49 N Vm (500 kgf Vcm, 36 ft Vlbf)
4. BLEED POWER STEERING SYSTEM
(See page SR±115)
±
STEERING POWER STEERINGSR±119
WhereEverybodyKnowsYourName

COMPONENTS
SR0G5±03
SECTIONAL VIEW
SR0G6±01
SR±120±
STEERING POWER STEERING
WhereEverybodyKnowsYourName