torque LEXUS SC400 1991 Service Repair Manual

SERVICE SPECIFICATIONS
SERVICE DATA
MA002±0B 








Engine 








Spark plug
Recommended spark plug
Correct electrode gap
Firing order
Valve clearance 








ND
NGK
Intake
Exhaust
\








\
PK20R11
BKR6EP11
1.1 mm (0.043 in.)
1 ± 8 ± 4 ± 3 ± 6 ± 5 ± 7 ± 2
0.15 ± 0.25 mm (0.006 ± 0.010 in.)
0.25 ± 0.35 mm (0.010 ± 0.014 in.)
 






BrakeFront and rear brakes
Pad thickness
Disc thickness
Limit
Limit (Front) (Rear)1.0 mm (0.039 in.)
30.0 mm (1.181 in.)
15.0 mm (0.591 in.)
 




Disc runout
Parking brake
Lining thickness
Drum inside diameter
()
Limit
Limit
Limit
()
0.05 mm (0.0020 in.)
1.0 mm (0.039 in.)
191 mm (7.520 in.)
 ChassisSteering linkage
Steering wheel freeplay
Limit30 mm (1.18 in.) 


gy
Ball joint
Vertical play
Limit
()
0.3 mm (0.012 in.)
MA002±0B
TORQUE SPECIFICATIONS
\
 \
Part tightened N
Vm kgf Vcm ft Vlbf
 Spark plug x Cylinder head1818013
 Front seat x Body3737527
 Front suspension crossmember x Body for nut1271,30094
  for bolt 201
,
2,050148
 Rear suspension member x Body1761,800130
 Rear suspension member rear cushion x Body3839028
±
MAINTENANCE (1UZ ± FE)MA±21
WhereEverybodyKnowsYourName

PREPARATION
EG0AZ±0A
RECOMMENDED TOOLS
MA009±02
EQUIPMENT
\
 
\

\
Dial indicator with magnetic base 


\
 \
Micrometer
\
 
\

\
MirrorBrake hose
\
 
\

\

Steel square
\
 \
Thermometer
\
 
\

\
Torque wrench
\
 \
Vernier calipers
MA00B±02
COOLANT 
Item
 
Capacity
 
Classification 

Engine coolant (w/ Heater)10.8 liters (11.4 US qts, 9.5 lmp. qts)Ethylene±glycol base
MA00D±0E
LUBRICANT
 Item Capacity Classification 

Engine oil (Drain and refill)
w/ Oil filter change
/ Oil filt h
 

4.8 liters (5.1 US qts, 4.2 lmp. qts)
 

API grade SG or SH, Energy±Conserving II
or ILSAC multigrade, and recommended
 


g
w/o Oil filter change 


4.8 liters (5.1 US qts, 4.2 lm. qts)
4.5 liters (4.8 US qts, 4.0 lmp. qts) 


or ILSAC multigrade, and recommended
viscosity oil with SAE 5W±30 being pre-
ferred engine oil
 Brake fluid Ð SAE J1703 or FMVSS No.116 DOT3
 Automatic transmission fluid 1.9 liters (2.0 US qts, 1.7 lmp. qts) ATF TYPE T±II

Automatic transmission fluid
(Drain and refill)
1.9 liters (2.0 US qts, 1.7 lm . qts)

AT F TYPE TII
 




Differential oil 




1.35 liters (1.43 US qts, 1.19 lmp. qts) 




Hypoid gear oil API GL±5
Above±18
5C (0 5F): SAE 90
Below±18 5C (0 5F): SAE 80W±90 or 80W
±
MAINTENANCE (1UZ ± FE)MA±5
WhereEverybodyKnowsYourName

5. REPLACE SPARK PLUGS(See Ignition System, steps 1 to 8 on pages IG±16 to 18)
(a) Remove the No.3 timing belt covers.
(b) Disconnect the high±tension cords at the rubber boot. Do not
pull on the high±tension cords.
NOTICE: Pulling on or bending the cords may damage
the conductor inside.
(c) Using a 16 mm plug wrench, remove the 8 spark plugs.
(d) Check the electrode gap of new spark plugs.
Correct electrode gap: 1.1 mm (0.043 in.)
Recommended spark plug: PK20R11 for ND
BKR6EP11 for NGK
NOTICE: If adjusting the gap of a new spark plug, bend
only the base of the ground electrode. Do not touch the
tip.
(e) Using a 16 mm plug wrench, reinstall the 8 spark plugs.
Torque: 18 N Vm (180 kgf Vcm, 13 ft Vlbf)
(f) Reconnect the high±tension cords.
(g) Reinstall the No.3 timing belt covers.
(See Ignition System, steps 5 to 13 on pages IG±22 to 24)
MA±8
±
MAINTENANCE (1UZ ± FE)
WhereEverybodyKnowsYourName

(d) Clean the filter in the canister.Clean the filter by blowing 294 kPa (3 kgf/cm
2, 43 psi) of com-
pressed air into port A while holding port B closed.
NOTICE:
w Do not attempt to wash the canister.
w No activated carbon should come out.
(e) Reinstall the charcoal canister.
(See Emission Control System on page EG±222)
9. REPLACE GASKET IN FUEL TANK CAP
(a) Remove the old gasket from the tank cap. Do not damage the
cap.
(b) Install a new gasket by hand.
(c) Check the cap for damage or cracks.
(d) Install the cap and check the torque limiter.
10. INSPECT FUEL LINES AND CONNECTIONS Visually check the fuel lines for cracks, leakage, loose con-
nections, deformation or tank band looseness.
11. INSPECT EXHAUST PIPES AND MOUNTINGS Visually check the pipes, hangers and connections for se-
vere corrosion, leaks or damage.
12. ADJUST VALVE CLEARANCE (See Engine Mechanical on page EG±14)
Valve clearance (Cold):
Intake
.15 ± 0.25 mm (0.006 ± 0.010 in.)
Exhaust
.25 ± 0.35 mm (0.010 ± 0.014 in.)
MA±10
±
MAINTENANCE (1UZ ± FE)
WhereEverybodyKnowsYourName

ViscosityAbove ± 185C (05F) SAE 90
Below ± 18 5C (0 5F) SAE 80W±90 or 80W
Capacity:
1.35 liters (1.43 US qts, 1.19 lmp. qts)
(e) Reinstall the filler plug securely.
23. TIGHTEN BOLTS AND NUTS ON CHASSIS AND BODY Tighten the following parts.
wFront seat±to±body mounting bolts
Torque: 37 N Vm (375 kgf Vcm, 27 ft Vlbf)
w Front suspension crossmembers - to - body mounting
nuts and bolts
Torque:
127 N Vm (1.300 kgf Vcm, 94 ft Vlbf) for nut
201 N Vm (2,050 kgf Vcm, 148 ft Vlbf) for bolt
w Rear suspension member - to - body mounting bolts
Torque: 176 NVm (1,800 kgfVcm, 130 ftVlbf)
wRear suspension member rear cushion - to - body
mounting bolts
Torque: 38 N Vm (390 kgf Vcm, 28 ft Vlbf)
24. BODY INSPECTION
(a) Check the body exterior for dents, scratches and rust
(b) Check the underbody for rust and damage.
If necessary, replace or repair.
25. ROAD TEST
(a) Check the engine and chassis for abnormal noises.
(b) Check that the vehicle does not wander or pull to one side.
(c) Check that the brakes work properly and do not drag.
(d) Perform setting of the parking brake shoes and drum.
±
MAINTENANCE (1UZ ± FE)MA±17
WhereEverybodyKnowsYourName

SERVICE SPECIFICATIONS
SERVICE DATA
PR036±03 Shaft runout Limit\
 \
0.8 mm (0.031 in.)
 Joint angle No.2 joint\
 \
±15 01 ' + 36 '
  No.3 joint\
 \
54' + 36 '
TORQUE SPECIFICATIONS
PR037±04
\
 \
Part tightened NVm kgf Vcm ft Vlbf
\
 \
Propeller shaft x Differential 79 805 58
\
 \
Propeller shaft x Intermediate shaft 74 750 54
\
 \
Intermediate shaft x Center bearing x Universal joint flange   
\
 \
1st 181 1,850 134
\
 \
2nd Loosen nut Loosen nut Loosen nut
\
 \
3rd 69 700 51
\
 \
Center support bearing x Body 49 500 36
\
 \
Oxygen senser x Exhaust front pipe 44 450 33
\
 \
Exhaust front pipe x Exhaust manifold 43 440 32
\
 \
Exhaust center pipe x Exhaust front pipe 43 440 32
\
 \
Exhaust center pipe x Exhaust rear pipe 19 195 14
\
 \
Crossmember x Body 13 130 8
\
 \
Heat insulator x Body 5.4 55 48 in. Vlbf
PR±36±
PROPELLER SHAFT SERVICE SPECIFICATIONS
WhereEverybodyKnowsYourName

PREPARATION
SST (SPECIAL SERVICE TOOLS)
PR01A±04
RECOMMENDED TOOLS
PR01B±02
EQUIPMENT
PR01C±02
\
 
\


\

\

Torque wrench 




\
 
\

\

Dial indicator 


\
 
\


\

\

Vernier calipers
 




±
PROPELLER SHAFT PRECAUTION, TROUBLESHOOTINGPR±3
WhereEverybodyKnowsYourName

PROPELLER SHAFT INSTALLATION
PR04L±01
1. INSTALL PROPELLER SHAFT
(a) Apply grease to the flexible coupling centering bushings.
Grease:Molybdenum disulphide lithium base, NLGI No.1 or
No.2.
(b) Insert the propeller shaft from the vehicle's rear and connectthe transmission and differential.
NOTICE: Support the center support bearing by hand so
that the transmission and intermediate shaft, and propel-
ler shaft and differential, remain in a straight line.
(c) Temporarily install the center support bearing set bolts with the adjusting washers.
HINT: Use the adjusting washers which were removed.
(d) Align the matchmarks and connect the propeller shaft to the transmission.
(e) Install the 3 bolts, washers and nuts.
NOTICE: Bolts should be inserted from the propeller
shaft side.
Torque: 79 N Vm (805 kgf Vcm, 58 ft Vlbf)
(g) Align the matchmarks and install the propeller shaft on the
differential with the 3 bolts, washers and nuts.
NOTICE: Bolts should be inserted from the propeller
shaft side.
Torque: 79 N Vm (805 kgf Vcm, 58 ft Vlbf)
PR±12±
PROPELLER SHAFT PROPELLER SHAFT
WhereEverybodyKnowsYourName

If using a new propeller shaft w / Phasemarks:
Install the propeller shaft phasemarks and differential phase-
marks so that their respective alignment phasemarks match.
If the propeller shaft phasemarks and differential phase-
marks do not align, install the propeller shaft and differential
alignment phasemarks are as close together as possible.
w / o Phasemarks:
Install the propeller shaft.
(See page PR±12)
(h) Torque the center support bearing set bolts.
Torque: 49 N Vm (500 kgf Vcm, 36 ft Vlbf)
HINT: Adjust the center support bearing to keep the dimen-
sion within the limits, as shown.
Under the same condition, check if the center line of the cen-
ter support bearing is at right angles to the shaft axial direc-
tion.
(i) Using SST, tighten the adjusting nut. SST 09922±10010
Torque: 48 N Vm (490 kgf Vcm, 35 ft Vlbf)
HINT: Use a torque wrench with a fulcrum length of 350 mm
(13.8 in.).
2. INSPECT JOINT ANGLE (See page PR±15)
NOTICE: The joint angle should by all means be checked
when the propeller shaft is removed and installed.
3. INSTALL CROSSMEMBER BRACE Install the center floor crossmember brace and torque the 4
bolts.
Torque: 13 N Vm (130 kgf Vcm, 8 ft Vlbf)
±
PROPELLER SHAFT PROPELLER SHAFTPR±13
WhereEverybodyKnowsYourName

4. INSTALL HEAT INSULATORInstall the heat insulator and torque the 4 nuts.
Torque: 5.4 N Vm (55 kgf Vcm, 48 in. Vlbf)
5. INSTALL EXHAUST CENTER PIPE
(a) Install new gaskets.
(b) Install the exhaust center pipe.
(c) Install the exhaust center pipe to the 2 rings.
(d) Install and torque the new 4 nuts.
Torque: 19 N Vm (195 kgf Vcm, 14 ft Vlbf)
6. INSTALL EXHAUST FRONT PIPE
(a) Install new gaskets.
(b) Install the front pipe.
(c) Install and torque the 6 bolts and new nuts.
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
(d) Connect both oxygen sensors.
HINT: When connecting the oxygen sensor, turn it to the left
about 3 times.
NOTICE: After installing the oxygen sensor, check that
the wire is not twisted.
(e) Tighten the oxygen sensors.
Torque: 44 N Vm (450 kgf Vcm, 33 ft Vlbf)
(f) Connect the oxygen sensor grommets to the floor.
PR±14
±
PROPELLER SHAFT PROPELLER SHAFT
WhereEverybodyKnowsYourName