lock LEXUS SC400 1991 Service Repair Manual

(c) Install the hose clamp.
(d) Connect the following hoses:(1) PS air hose to No. 4 timing belt cover
(2) PCV hose to No. 2 cylinder head cover
(e) Connect the volume air flow meter connector.
(f) Connect the high±tension cord to the ignition coil.
18. CONNECT CONTROL CABLES TO THROTTLE BODY Connect the following cables:(1) Accelerator cables
(2) (A/T)
Throttle control cable
(3) Cruise control actuator cable
19. INSTALL BATTERY
20. FILL ENGINE WITH COOLANT (See page CO±5)
Capacity (w/Heater): M/T 8.5 liters (9.0 US qts, 7.5 lmp. qts)
A/T 8.4 liters (8.9 US qts, 7.4 lmp. qts)
21. START ENGINE AND CHECK FOR LEAKS
22. (A/T)CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
(See page MA±11)
NOTICE: Do not overfill.
23. CHECK IGNITION TIMING (See page IG±14)
Ignition timing:
105 BTDC @ idle
(w/ Terminals TE1 and E1 connected)
24. INSTALL ENGINE UNDER COVER
25. INSTALL HOOD
26. PERFORM ROAD TEST Check for abnormal noise, shock, slippage, correct shift
points and smooth operation.
27. RECHECK ENGINE COOLANT AND ENGINE OIL LEVELS
EM±112
±
ENGINE MECHANICAL Cylinder Block
WhereEverybodyKnowsYourName

SERVICE DATA (Cont'd)
TORQUE SPECIFICATIONS
\
\
Part tightened  NVm kgf Vcm ft Vlbf
\
\
Camshaft bearing cap X Cylinder head  20 200 14
\
No.1 cylinder head cover X Cylinder head5.45548 in. Vlbf\
\
No.2 cylinder head cover X Cylinder head  5.4 55 48 in. Vlbf\
\
Intake air connector X Air intake chamber  21 210 15\
\
Throttle body bracket X Throttle body  21 210 15\
\
Throttle body bracket X Cylinder head  21 210 15
\
\
EGR pipe X Intake manifold  21 210 15
\
\
EGR pipe X EGR valve  64 650 47
\
\
Spark plug X Cylinder head  18 180 13
\
\
Throttle body X Intake air connector  21 210 15
\
\
Idler pulley X Oil pump  34 350 25
\
Crankshaft pulley X Crankshaft3243,300239\
\
Camshaft timing pulley X Camshaft  79 810 59\
\
Timing belt tensioner X Oil pump  26 270 20\
\
Drive belt tensioner X Cylinder head  21 210 15\
\
EGR cooler X Cylinder head  14 140 10
\


\
Engine coolant temperature sensor X Cylinder
head 


 


20 


200 


14
\


\
Engine coolant temperature sender gauge X Cylin-
der head 


 


20 


200 


14
\
\
Engine hanger X Cylinder head  39 400 29
\
Cylinder head X Cylinder block1st3435025\
\
 2nd Turn 90
5  
\
\
 3rd Turn 905  
\
\
No.4 Timing belt cover X Cylinder head  8.8 90 78 in.Vlbf\
\
Intake manifold X Cylinder head  21 210 15
\
\
Intake manifold stay X Intake manifold  39 400 29
\
\
Intake manifold stay X Cylinder head  39 400 29
\
\
No.1 fuel pipe X Intake manifold  8.8 90 78 in. Vlbf
\
\
No.2 fuel pipe X Intake manifold  8.8 90 78 in. Vlbf
\
\
Delivery pipe X Intake manifold  21 210 15
\
\
Air intake chamber X Intake manifold  21 210 15
\
Air intake chamber stay X Air intake chamber1818513\
\
Air intake chamber stay X Cylinder head  18 185 13\
\
Vacuum control valve set X Intake manifold  21 210 15\
\
No.2 vacuum pipe X Air intake chamber  21 210 15\
\
Water outlet X Cylinder head  21 210 15
\
\
Water by±pass outlet X Cylinder head  8.8 90 78 in. Vlbf
\
\
Exhaust manifold X Cylinder head  39 400 29
\
\
Exhaust manifold heat insulator X Exhaust manifold  18 185 13
EM±116±
ENGINE MECHANICAL Service Specifications
WhereEverybodyKnowsYourName

TORQUE SPECIFICATIONS (Cont'd)
 Part tightened  NVm kgf Vcm ft Vlbf
 Main bearing cap X Cylinder block 1st 44 450 33
  2nd Turn 90 5  
 Connecting rod cap X Connecting rod 1st 29 300 22
2ndTurn 905 Rear oil seal retainer X Cylinder block  5.9 60 52 in.Vlbf Oil filter bracket X Cylinder block  88 900 65 LH engine mounting bracket X Cylinder block  58 590 43 RH engine mounting bracket X Cylinder block  58 590 43
 Knock sensor X Cylinder block  44 450 33
 Oil pressure switch X Cylinder block  14 150 11
 Fuel pipe support X Cylinder block  14 145 10
 Fuel pressure pulsation damper  41 420 30
  (for SST) 35 350 25
 Generator X Cylinder block  37 380 27
Flywheel X Crankshaft (M/T)1st4950036  2nd Turn 90 5  
 Drive Plate X Crankshaft (A/T)  98 1,000 72 Starter X Transmission  39 400 29 Oil cooler pipe X Transmission (A/T)  34 350 25
 Rear engine mounting member X Body  25 260 19
 


Rear engine mounting member X Engine mounting
insulator 


 


13 


135 


10
 Intermediate shaft X Propeller shaft  74 750 54
 Propeller shaft center bearing X Body  49 500 36
No.2 front exhaust pipe X Exhaust manifold6263046 Front exhaust pipe X No.2 front exhaust pipe  43 440 
 Clutch release cylinder X Transmission (M/T)  12 120 9 Fuel inlet hose X Fuel pipe support  34 350 25 A/C compressor X Cylinder block Through bolt 26 265 19
  Bolt and nut 52 530 38
 PS pump X Cylinder block  58 590 43
 PS pump X A/C compressor  58 590 43
 PS pump X Pump rear stay  39 400 29
 Cylinder block X Pump rear stay  39 400 29
 Fluid coupling X Water water pump  16 165 12
±
ENGINE MECHANICAL Service SpecificationsEM±117
WhereEverybodyKnowsYourName

INSPECTION OF INJECTORS
1. INSPECT INJECTOR INJECTIONCAUTION: Keep injector clear of sparks during the test.
(a) Disconnect the fuel inlet hose from the fuel tube.
(b) Connect SST (hose) to the fuel inlet tube with SST(union). Tighten the flare nut on the fuel tube.
SST 09268±41045 (90405±52010)
Torque: 30 N Vm (310 kgf Vcm, 22 ft Vlbf)
HINT: Use SST. (See page FI±15)
SST 09631±22020
(c) Loosen the lock nut, and remove the pressure regulator from the RH delivery pipe. Remove the O±ring from the
pressure regulator.
(d) Install a new O±ring to the fuel inlet of the pressure regulator.
(e) Connect SST (hose) to the pressure regulator with SST (union). Tighten the lock nut on the pressure regulator.
SST 09268±41045 (09268±52010)
Torque: 29 N Vm (300 kgf Vcm, 22 ft Vlbf)
(f) Connect the fuel return hose to the fuel outlet of the
pressure regulator with SST (union), two new gaskets
and union bolt.
SST 09268±41045 (09268±41070)
FI±52EFI SYSTEM ± Fuel System (Injectors)
WhereEverybodyKnowsYourName

(e) Reinstall the fuel pressure regulator to the RH deliverypipe.
w Fully loosen the lock nut on the pressure regulator.
w Apply a light coat of gasoline to a new O±ring, and
install it to the pressure regulator.
w Completely insert the pressure regulator into the
delivery pipe by hand.
w Turn the pressure regulator counterclockwise until
the vacuum sensing port faces in the direction
indicated in the illustration.
INSTALLATION OF INJECTORS
(See Components on page FI±49)
1. INSTALL INJECTORS AND DELIVERY PIPE (a) Install the grommet to each injector.
(b) Apply a light coat of gasoline to a new O±ring and install
it to each injector.
(c) W h i l e t u r n i n g t h e i n j e c t o r c l o c k w i s e a n d counterclockwise, push it to the delivery pipes. Install
the eight injectors.
(d) Position the injector connector outward.
(e) Place the eight insulators and four spacers in position on the intake manifold.
FI±54
EFI SYSTEM
± Fuel System (Injectors)
WhereEverybodyKnowsYourName

(f) Place the eight injectors and two delivery pipesassembly in position on the intake manifold.
(g) Temporarily install the c onnector bracket and four
mounting bolts.
(h) Check that the injectors rotate smoothly.
HINT: If injectors do not rotate smoothly, the probable cause
is incorrect installation of O±rings. Replace the O±rings.
(i) Position the injector connector outward.
(j) Tighten the four bolts holding the delivery pipes to the intake manifold.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
2. INSTALL FUEL RETURN PIPE
(a) Temporarily install the return pipe with the bolt, two
gaskets and union bolt.
(b) Tighten the union bolt holding the return pipe to the pressure regulator.
Torque: 35 N Vm (360 kgf Vcm, 26 ft Vlbf)
(c) Tighten the bolt holding the return pipe to the LH cylinder
head.
3. TIGHTEN LOCK NUT ON FUEL PRESSURE REGULATOR
Torque: 29 N Vm (300 kgf Vcm, 22 ft Vlbf)
FI±55EFI SYSTEM ± Fuel System (Injectors)
WhereEverybodyKnowsYourName

COMPONENTS
REMOVAL OF ACOUSTIC CONTROL
INDUCTION SYSTEM (ACIS)
1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OFBATTERY
CAUTION: Turn the ignition switch to ºLOCKº. Discon-
nect the cable from the negative (±) terminal of the bat-
tery. Wait at least 20 seconds before proceeding with
work.
2. (A/T) REMOVE DIPSTICK GUIDE FOR TRANSMISSION
(a) Remove the mounting bolt.
(b) P u ll ou t th e dip stick gu id e an d dip stick fro m th etransmission.
(c) Remove the O±ring from the dipstic guide.
±
EFI SYSTEMFI±57
Air Induction System (Acoustic Control Induction System (ACIS)
WhereEverybodyKnowsYourName

REMOVAL OF FUEL PRESSURE
PULSATION DAMPER
(See Component on page FI±58)
1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY
CAUTION: Work must be started after approx. 20 se-
conds or longer from the time the ignition switch is
turned to the ºLOCKº position and the negative (±) termi-
nal cable is disconnected from the battery.
2. REMOVE UPPER HIGH±TENSION CORD COVER (a) Remove the two mounting bolts.
(b) Disconnect the front side claw groove of the cord coverfrom the claw of the lower cover, and remove the cord
cover.
3. REMOVE LH ENGINE WIRE COVER Remove the two bolts and engine wire cover.
4. REMOVE FUEL PRESSURE PULSATION DAMPER (a) Remove the pulsation damper and upper gasket.
(b) Disconnect the fuel inlet hose from the delivery pipe,and remove the lower gasket. FI±59
EFI SYSTEM
± Fuel System (Fuel Pressure Pulsation Damper)
WhereEverybodyKnowsYourName

COMPONENTS
REMOVAL OF AIR FLOW METER
1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OFBATTERY
CAUTION: Work must be started after approx. 20 se-
conds or longer from the time the ignition switch is
turned to the ºLOCKº position and the negative (±) termi-
nal cable is disconnected from the battery.
2. DISCONNECT AIR FLOW METER CONNECTOR
(a) Disconnect the air flow meter connector.
(b) Disconnect the wire clamp from the clamp bracket onthe air flow meter.
3. REMOVE AIR CLEANER CASE AND AIR FLOW METER ASSEMBLY
(a) Loosen the hose clamp.
(b) Remove the four mounting bolts.
(c) Disconnect the air cleaner hose from the air flow meter.
(d) Disconnect the air duct from the air cleaner case, andremove the air cleaner case and air flow meter
assembly.
FI±64
EFI SYSTEM
± Air Induction System (Air Flow Meter)
WhereEverybodyKnowsYourName

REMOVAL OF THROTTLE BODY
(See Components on page FI±69)
1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY
CAUTION: Work must be started after approx. 20 se-
conds or longer from the time the ignition switch is
turned to the ºLOCKº position and the negative (±) termi-
nal cable is disconnected from the battery.
2. DRAIN ENGINE COOLANT (See page CO±6)
3. REMOVE THROTTLE BODY COVER (a) Remove the mounting cap nut.
(b) Loosen the two bolts, and remove the throttle bodycover.
4. DISCONNECT CONTROL CABLES FROM THROTTLE BODY
Disconnect the following cables:(1) Accelerator cable
(2) A/T throttle control cable
(3) (w/ Cruise Control System)
Cruise control actuator cable
5. REMOVE INTAKE AIR CONNECTOR (a) Disconnect the following hoses:(1) Air hose from ISC valve
(2) Air hose (from PS air control valve) from intake air connector
(b) Remove the bolt holding the intake air connector to the cylinder head cover.
(c) Loosen the two hose clamps.
(d) Disconnect the intake air connector from the throttle body and air cleaner hose, and remove the intake air
connector.
FI±70
EFI SYSTEM
± Air Induction System (Throttle Body)
WhereEverybodyKnowsYourName