homelink LINCOLN MKZ HYBRID 2013 Owners Manual
[x] Cancel search | Manufacturer: LINCOLN, Model Year: 2013, Model line: MKZ HYBRID, Model: LINCOLN MKZ HYBRID 2013Pages: 475, PDF Size: 3.89 MB
Page 155 of 475
HomeLink Wireless Control
System (If Equipped)
WARNING
Do not use the system with any
garage door opener that does
not have the safety stop and reverse
feature as required by U.S. Federal
Safety Standards (this includes any
garage door opener manufactured
before April 1, 1982). A garage door
opener which cannot detect an object,
signaling the door to stop and reverse,
does not meet current federal safety
standards. Using a garage door opener
without these features increases the
risk of serious injury or death. Note:
Make sure that the garage door
and security device are free from
obstruction when you are
programming. Do not program the
system with the vehicle in the garage.
Note: Make sure you keep the original
remote control transmitter for use in
other vehicles as well as for future
system programming.
Note: We recommend that upon the
sale or lease termination of your
vehicle, you erase the programmed
function buttons for security reasons.
See Erasing the function button codes
later in this section.
Note: You can program a maximum
of three devices. To change or replace
any of the three devices after it has
been initially programmed, you must
first erase the current settings. See
Erasing the function button codes later
in this section. The universal garage door opener
replaces the common hand-held
garage door opener with a
three-button transmitter that is
integrated into the driver
’s sun visor.
The system includes two primary
features, a garage door opener and a
platform for remote activation of
devices within the home. As well as
being programmed for garage doors,
the system transmitter can be
programmed to operate entry gate
operators, security systems, entry
door locks and home or office lighting.
Additional system information can be
found online at www.homelink.com
or by calling the toll-free help line on
1-800-355-3515.
In-vehicle programming
This process is to program your
hand-held transmitter and your
in-vehicle HomeLink button.
Note: Put a new battery in the
hand-held transmitter. This will ensure
quicker training and accurate
transmission of the radio-frequency
signal.
153
MKZ (CC9) Universal Garage Door OpenerE142657
Page 156 of 475
1. With your vehicle parked outside
of the garage, turn your ignition to
the on position, but do not start
your vehicle.
2. Hold your hand-held garage door transmitter 1– 3 inches (2–8
centimeters) away from the
HomeLink button you want to
program.
3. Using both hands, simultaneously,
press and hold the desired
HomeLink button and the
hand-held transmitter button. DO
NOT release either one until the
HomeLink indicator light flashes
slowly and then rapidly. When the
indicator light flashes rapidly, both
buttons may be released. The
rapid flashing indicates successful
training.
4. Press and hold the HomeLink button you programmed for five
seconds, then release. You may
need to do this twice to activate
the door. If your garage door does
not operate, watch the HomeLink
indicator light.
If the indicator light stays on, the
programming is complete. See
Programming your garage door
motor
later in this section. If the indicator light flashes rapidly for
2 seconds and then turns to a
constant light, the HomeLink button
is not programmed yet. Do the
following:
Press and hold the HomeLink button
while you press and release the
hand-held transmitter button every 2
seconds. The HomeLink indicator light
will flash slowly and then rapidly once
the HomeLink function button
recognizes and accepts the hand-held
transmitter
’s radio frequency signal.
After programming the HomeLink
button, begin programming your
garage door opener motor.
Note: You may need a ladder to reach
the unit and you may need to remove
the cover or lamp lens on your garage
door opener. To program additional buttons, repeat
Steps 1 – 4.
For questions or comments, please
contact HomeLink at
www.homelink.com or
1-800-355-3515.
154
MKZ (CC9) Universal Garage Door OpenerE142658 E142659
Page 157 of 475
Programming your garage door
opener motor
1. Press the learn button on the
garage door opener motor and
then you have 30 seconds to
complete the next two steps.
2. Return to your vehicle. 3.
Press and hold the function button
you want to program for 2
seconds, then release. Repeat this
step. Depending on your brand of
garage door opener, you may need
to repeat this sequence a third
time.
Erasing the Function Button Codes
Note: You cannot erase individual
buttons. 1. Press and hold the outer two
function buttons simultaneously
for approximately 20 seconds until
the indicator lights above the
buttons flash rapidly.
2. When the indicator lights flash, release the buttons. The codes for
all buttons are erased.
Reprogramming a Single Button
To program a device to a previously
trained button, follow these steps:
1. Press and hold the desired button.
Do NOT release the button.
2. The indicator light will begin to flash after 20 seconds. Without
releasing the button, follow Step
1 in the Programming section.
For questions or comments, contact
HomeLink at www.homelink.com or
1-800-355-3515.
Programming to a Genie
Intellicode 2 Garage Door Opener
Note: The Genie Intellicode 2
transmitter must already be
programmed to operate with the
garage door opener.
Note: To program HomeLink to the
transmitter you must first put the
transmitter into programming mode.
155
MKZ (CC9) Universal Garage Door OpenerE142658 E142660
Page 158 of 475
Red indicator light
A.
Green indicator light
B.
1. Press and hold one of the buttons
on the hand-held transmitter for
10 seconds. The indicator light will
change from green to red and
green.
2. Press the same button twice to confirm the change to
programming mode. If done
properly the indicator light will
appear red.
3. Hold the transmitter within 1– 3
inches (2 –8 centimeters) of the
button on the visor you want to
program.
4. Press and hold both the programmed Genie button on the
hand-held transmitter and the
button you want to program. The
indicator light on the visor will flash
rapidly when the programming is
successful. Note:
The Genie transmitter will
transmit for up to 30 seconds. If
HomeLink does not program within 30
seconds the Genie transmitter will need
to be pressed again. If the Genie
transmitter indicator light displays
green and red, release the button until
the indicator light turns off before
pressing the button again.
Once HomeLink has been
programmed successfully, the Genie
transmitter must be changed out of
program mode. To do this:
1. Press and hold the previously programmed Genie button on the
hand-held transmitter for 10
seconds. The indicator light will
change from red to red and green.
2. Press the same button twice to confirm the change. If done
correctly the indicator light will
turn green.
Programming HomeLink to the
Genie Intellicode Garage Door
Opener Motor
Note: You may need a ladder to
access the garage door opener motor. 156
MKZ (CC9) Universal Garage Door OpenerBAE142661 E142662
Page 159 of 475
1.
Press and hold the program button
on the garage door opener motor
until both blue indicator lights turn
on.
2. Release the program button. Only the smaller round indicator light
should be on.
3. Press and release the program button. The larger purple indicator
light will flash.
Note: The next two steps must be
completed in 30 seconds.
4. Press and release the Genie Intellicode 2 hand-held
transmitter ’s previously
programmed button. Both
indicator lights on the garage door
opener motor unit should now
flash purple.
5. Press and hold the previously programmed button on the visor
for 2 seconds. Repeat this step up
to 3 times until the garage door
moves.
Programming is now complete.
Clearing a HomeLink Device
To erase programming from the three
HomeLink buttons press and hold the
two outer HomeLink buttons until the
indicator light begins to flash. The
indicator light will begin flashing in 10
to 20 seconds, at which time both
buttons should be released.
Programming has now been erased,
and the indicator light should blink
slowly to indicate the device is in train
mode when any of the three
HomeLink buttons are pressed. FCC and RSS-210 Industry Canada
Compliance
This device complies with Part 15 of
the FCC Rules and with RSS-210 of
Industry Canada. Operation is subject
to the following two conditions: (1)
this device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Changes or modifications to your
device not expressly approved by the
party responsible for compliance can
void the user
’s authority to operate
the equipment.
157
MKZ (CC9) Universal Garage Door Opener
Page 472 of 475
Traction Control..................................196
Principle of Operation............................196
Transmission Code Designation........................................333
Transmission........................................185
Transmission See: Transmission....................................185
Transporting the Vehicle.................244
U
Under Hood Overview - 2.0L Hybrid...................................................278
Unique Driving Characteristics......166
Universal Garage Door Opener..................................................153
HomeLink Wireless Control System...................................................... 153
Using Adaptive Cruise Control........211 Blocked Sensor.......................................... 216
Changing the Set Speed........................215
Detection Issues........................................215
Disengaging the System........................214
ECO Cruise Control..................................218
Following a Vehicle..................................212
Hilly Condition Usage..............................215
Low Speed Automatic Cancellation........................................... 215
Overriding the System............................214
Resuming the Set Speed.......................215
Setting a Speed......................................... 212
Setting the Gap Distance.......................213
Switching the System Off.....................215
Switching the System On......................212
Switching to Normal Cruise Control...................................................... 217
System Not Available.............................216
Using Cruise Control..........................210 ECO Cruise Control....................................211
Switching Cruise Control Off.................211
Switching Cruise Control On................210 Using MyKey With Remote Start
Systems.................................................59
Using Snow Chains............................328
Using Stability Control......................198 AdvanceTrac® .......................................... 198
Using Traction Control......................196 System Indicator Lights and
Messages................................................ 196
Utilizing the Mediation/Arbitration Program (Canada Only)................261
V
Vehicle Care.........................................294
General Information...............................294
Vehicle Certification Label
..............333
Vehicle Identification Number.......332
Vehicle Storage..................................300
Battery.......................................................... 301
Body............................................................. 300
Brakes........................................................... 301
Cooling system.......................................... 301
Engine.......................................................... 300
Fuel system............................................... 300
General....................................................... 300
Miscellaneous............................................ 301
Removing Vehicle From Storage........301
Tires............................................................... 301
Ventilated Seats
...................................151
Heated and ventilated seat air filter
replacement (if equipped)...............152
Ventilation See: Climate Control...............................138
VIN See: Vehicle Identification Number...332
Voice Control
...........................................77
470
MKZ Hybrid (CC9) Index