ignition LINCOLN NAVIGATOR 2014 Quick Reference Guide

1 Lighting Control
Turns on the headlamps.
Turns the headlamps off.
Turns on the parking lamps.
Autolamps: Automatically turns the exterior
lamps on/off based on available daylight.
Turns on fog lamps by pulling the control
toward you. The fog lamps can be turned
on when the ignition is on and the lighting
control knob is in the parking lamps on,
headlamps on, or autolamps positions and
the high beams are not turned on.
2 Parking Brake
3 Windshield Wipers and Washers
Rotate the end of the control stalk away
from you/toward you to increase/decrease
the speed of the wipers.
To use the washer feature, push the end
of the stalk:

Quickly for a single swipe without fluid.

Hold briefly for three swipes with
washer fluid.

Hold for a longer wash cycle.
To operate your rear window wiper:
Turn the rear wiper control to 1 (slower
intermittent speed), 2 (faster intermittent
speed) or O (off). For a rear wash cycle,
rotate and hold the
control to either
the top or bottom position to activate the
rear washer. The control will return to the
2 or 0 position when you release it.
Note: For optimal wiper performance, clean
your blades and glass regularly. Refer to
your Owner’s Manual for more information.
4 Cruise Control
To set the speed:
1. Press and release ON.
2. Accelerate to the desired speed.
3. Press SET+ and take your foot
off the accelerator.

To set a higher or lower speed, press
and hold SET+/SET– until the desired
speed is reached. You can also press
and release either button to change your
set speed minimally (in approximately
1 mph [2 km/h] increments).

To cancel a set speed, tap the brake
pedal. The set speed will not be erased.

To return to a previously set speed,
press RESUME.

To turn off, press OFF or turn off
the ignition.
5 Information Display
Shows important vehicle information
through a constant monitor of vehicle
systems. The display will notify you of
potential vehicle problems by showing
system warnings followed by a long
indicator tone. For more details about
your information display functions,
please see your Owner’s Manual.
6 Service Engine Soon Light
Illuminates briefly when the ignition
is turned on. If it remains on or is
blinking after the engine is started, the
On-Board Diagnostics (OBD-II) system
has detected a malfunction. Drive in
a moderate fashion and contact your
authorized dealer as soon as possible.
7 Hazard Control
4 5
Instrument Panel2014 NAVIGATOR

Tips
Make sure you accept SYNC’s request
to access your phone.
To pair subsequent phones or to learn
more about your SYNC system, please
refer to Pairing Subsequent Phones in the
SYNC chapter of your Owner’s Manual .
Using My Phone with SYNC
Note: You must download your phone book
to make phone calls with voice commands
by name.
Making a Phone Call
Use SYNC to make a phone call to anyone
in your phone book by pressing the voice
button and when prompted, give a
voice command.
For example, you could say “ Call Jake Smith
at home ”. When the system confirms the
number, say “ Dial” again to initiate the call.
Note: You can also make phone calls
by pressing the voice button
. When
prompted, give the voice command “ Dial”,
then verbally say the phone number. Answering Incoming Calls
Whenever you have an incoming call, you
will be able to see the name and number of
the person calling in your display. Press the
phone button
to answer an incoming
call. You can hang up at any time by
pressing and holding the phone button
.
Do Not Disturb Mode
This feature blocks incoming calls and tex t
messages, and saves them for later. You
still have access to outgoing calls when this
feature is active. Say the voice command
“ Do not disturb on ” to enable and “Do not
disturb off ” to disable.
Using SYNC to Access Digital Media
SYNC has a media hub with multiple inputs
allowing you to access personal media from
your digital devices. Plug in your USB media
devices such as phones and MP3 players,
and use SYNC to play all of your favorite
music. SYNC indexes all of your music. The
more music that is stored on your device,
the longer it takes SYNC to index.Using Voice Commands to Play Music
1. Plug your media player into your
USB port.
2. Press the voice button
. When
prompted, say “ USB”, then follow-up
saying one of the following
voice commands.
SYNC AppLinkTM*
SYNC AppLink allows voice access to
select mobile applications that you already
have or can download to your Android
TM,
BlackBerry® or iPhone®.
Current apps available include Pandora
Internet Radio®, Stitcher Smar t Radio
TM,
Open Beak (BlackBerry exclusive),
IHear tRadio, Slacker, NPR News and
SYNC Destinations and more.
For more information on SYNC, visit the
website or call the toll-free number. See the
inside front cover of this guide for details.
SYNC®
Getting Started with Your SYNC System
SYNC is a hands-free, voice recognition system used
for entertainment, information and communication.
SYNC. Say the Word.
General Tips
Press RETURN to exit a menu.
For additional suppor t, refer to your Owner’s Manual , visit the
website or call the toll-free number. See the inside front cover
of this guide for details.
Before You Get Started 1. Set up your owner account by visiting SyncMyRide.com (U.S.)
or SyncMyRide.ca (Canada). Follow the on-screen instructions.
Note: Your account gives you even more SYNC capabilities,
including personalization features and software updates.
2. SYNC uses a wireless connection called
Bluetooth® to
communicate with your phone. Turn Bluetooth mode on in
your phone's menu options. This lets your phone find SYNC.
For more details on setting up your phone with SYNC, visit
SyncMyRide.com (U.S.), SyncMyRide.ca (Canada) or your
phone manufacturer’s website.
8 9
*if equipped
2014 NAVIGATOR
Pairing Your Phone with SYNC
Pair your phone to use many
of the features of SYNC.
To Pair Your Phone for the
First Time 1. Make sure that your vehicle
is in P (Park) and both
your ignition and radio
are turned on.
2. Press the phone button
on your steering
wheel or the Phone button
on your audio controls.
When the No phone paired
message comes up on the
screen, press Settings ,
then press Add to add your
cellular phone.
3. Make sure that Bluetooth
is set to on and your cellular
phone is in the proper
mode. Refer to your phone’s
user guide, if necessar y.
4. Find SYNC will appear on
the touchscreen, indicating that it is tr ying to pair with
your cellular phone. When
it finds your phone, a
six-digit PIN
will appear
on your touchscreen.
5. When prompted on your cellular phone’s display,
enter the six-digit PIN
provided by SYNC into
your cellular phone.
6. The display indicates when
the pairing is successful.
Note: The system may prompt
you to:
Set your phone as the
primary/favorite (the primar y
phone will receive messages
and voicemail).
Download your phone
book (this is required
to use the full set of
voice commands).
Turn on 911 Assist®.

Second-row Heated Seats
The rear heated seat controls are
located on the rear of the center
console. Press the indicated side
of the control
for maximum
heat. Press again to deactivate.
Press the indicated side of the
control
for minimum heat.
Press again to deactivate.
Note: The heated seats reset at
every ignition run cycle. They will
turn off automatically when the
engine is turned off.
Memory Seat Feature
The memory function will save
and recall the positions of the
driver seat, power mirrors,
adjustable pedals and steering
column. Use the control located
on the side of the driver’s seat
to program and then
recall saved memory positions.
To program position 1, switch the
ignition on. Move the memory
features to your preferred
position. Press and hold the
1 button
for about two
seconds until you hear a tone.
Use this same procedure to set
the second position by using the
2 button
. You can now use
these controls to recall the set
memory positions.
Convenience
Rain-sensing Wipers
If activated, your wipers will
automatically turn on when
moisture is present on the
windshield. The wipers will not
cycle until moisture is detected
on the windshield, and the wiper
speed will vary based on the
amount of moisture detected on
the windshield and the sensitivity
setting. The wipers will continue
to wipe as long as moisture is
detected. To deactivate, turn
your wiper controls off.
Note: Make sure that this feature
is turned off before entering a
car wash.
MyKey®
MyKey allows you to program
certain driving restrictions in
order to promote good driving
habits. You can set speed
restrictions and limit volume
levels. For complete information,
refer to the MyKey chapter in
your Owner’s Manual.
Power Liftgate
Press
on the instrument
panel to open or close the power
liftgate. For added convenience,
there are three more ways
to activate your power
liftgate’s capabilities:
1. On your remote entry
transmitter, press
twice
within three seconds to open
or close your power liftgate.
2. To open using the liftgate
control button in the liftgate
handle: Unlock the doors
using either the remote entry
transmitter or the power door
unlock control, and press
the control. 3.
To close using the rear
cargo area button: Press and
release the
control
located on the left rear
quarter panel. This button is
automatically disabled when
the liftgate is latched.
Note: Keep clear of the liftgate
when operating the rear switch.
Your power liftgate is equipped
with an obstacle detection
feature which will either stop or
revert to a full open position if
it encounters a solid object. For
complete information, see the
Liftgate section within the Locks
chapter of your Owner’s Manual.
Power-Adjustable Foot Pedals
Located to the left of your
steering column, your power-
adjustable pedal control lets you
move your brake and accelerator
pedals closer. Press the
arrow
to move the pedals closer to
you or the
arrow to move
the pedals further away from you. The pedals should only be
adjusted when the vehicle is
stopped and in P (Park).
SecuriCodeTM Keyless
Entry Keypad

Lock or unlock the doors or
release the liftgate glass without
using a key. The keypad can be
operated with the factory-set,
5-digit entry code; this code is
located on the owner’s wallet
card in the glove box. You can
also create up to five of your own
5-digit personal entry codes. To
lock all of the doors and liftgate,
press and hold 7•8 and 9•0 at
the same time. For complete
information, refer to the Locks
chapter of your Owner’s Manual.
10 11
*if equipped
2014 NAVIGATORComfort
PowerFold® Third-row Seat*
60/40 split-folding bench seat
uses a power-activated seatback
release. Fold one side or both
down for more flexibility.
The controls are located on
the right-hand rear quarter trim
panel that is accessible from
the liftgate area.
Note: Make sure all seatbelts
are unfastened.
To lower:
1. Make sure that the head
restraints are folded down first.
2. Press “FOLD” on the button. 3.
To return the seatback to its
original position, press “UP”
on the button.
Note: The power-folding seats
will operate for 10 minutes after
the ignition switch is turned off.
The transmission must be in
P (Park) and the liftgate or
liftgate glass must be open.
Front Heated and
Ventilated Seats

Press the heated seat symbol
or the ventilated seat symbol
to cycle through the various
settings and off. Warmer or cooler
settings are indicated by more
indicator lights.