bumper MAZDA 323 1992 Workshop Manual Suplement

TURBOCHARGER CONTROL SYSTEM F3
INTERCOOLER
Removal / Installation
1 I Remove the front bumper. (Refer to Section S.)
2. Remove in the order shown in the figure.
3. Install in the reverse order of removal.
7-i-11 N-h l80-110 kgfem, 69-95 In-lbf 1
1.
Air hose 2. Intercooler
wrn 1 kgf-m, ft-lbf I
13EOF3-34:

S
BODY
INDEX . . . . . ..*.I........**........*.~*.~............*.......
s- 2
OUTLINE ..................................................
s- 3
UUJLINE OF CONSTRUCTION ..................
S- 3
BONNET BULGE
....................................
s- 3
RADIATOR GRILLE ................................. s- 4
FRONT BUMPER .................................... s- 4
REAR SKIRT ...........................................
s- 6
WHEEL ARCl-i MOLDING .........................
s- 5
( SERVICE j
SUPPLEMENTAL SERVICE fNFURMATION.. S- 6
BONNET BULGE
.......................................
s- 7
COMPONENTS ....................................... s- ‘7
FRONT BUMPER
.......................................
s- 8
COMPONENTS .......................................
s- 8
REAR SKIRT .............................................
S-10
COhiIPONENTS .......................................
S-10
Wt=fEEL ARCH MOLDING ............................
S-l 1
COMPONENTS .......................................
S-l 1
13EOSX301

S INDEX
INDEX
1. Bonnet bulge
Removal ! Installation _. __. . . , , . . l.. . .__ page. S-
2. Fro.nt bumper
7 Removal / Installation
. . . . . 1 . . . . . . . ,‘... page S-
Disassembly / Assembly 8
. ..a I........
page S- 9
s-2 3. Rear skirt
Removal / t’nstaltation 4. Wheel arch molding .....n.....ba..... page S-l 0
Removal / Installation
. .-. . . , , ..‘. .-. page S-l 1
OUTLINE
l The exteric
bofiy.
OUTLtNE 01
i BONNET BUt
l Bonnet bulg
a high-qualit

l The exterior parts are designed to emphasize the function and appearance of the superbly proportioned
body.
: OUTtlNE OF CONSTRUCTION
1 xosx.303
.c
Bonnet bulges are provided in bonnet
. . . . . . . . . . . . ..I................~.....
s-3
A large, body-colored front bumper fascia is adopted., , ..,..,.... S-4
Wheel arch moldings are fitted to fenders . . . . . . . ,..*. l.. . . . . . . . . . . . . . . . . . S-5
- Air inlet area of radiator grille is enlarged
................................. S-4
- Bumper mesh is provided in front bumper
..............................
s-4 Rear skirt is attached under rear bumper.. ............................... S-5
13EOSX-304 BONNET BULGE
l Bonnet bulges are fittGd to the bonnet to match the dynamic appearance of the vehicle and to give it
a high-quality look.

UUTLINE
RADfATOR GRfLtE
l The air inlet area of the radiator grille is enlarged for improved cooling efficiency.
FRONT BUMPER
l The large front bu,mper includes fog lights and bumper mesh to give the vehicle a dynamic appearance.
l tight and rigid polyurethane is used for the bumper fascia.
l The air inlet area is adopted for improved cooling efficiency.
s-4
REAR SKI
l The rear 5
l Light and
WHEEL AR4
l Wheel arc

S SUPPLEMENTAL SERVICE INFORMATION
SUPPLEMENTAL SERVICE lNFORMATlON
The following points in this section are changed in comparison with 323 Workshop Manual (1229-~()439~).
*
BONNET BULGE
l Removal / installation
FRONT BUMPER
l Removal / Installation
REAR SKIRT
l Removal / Installation
WHEEL ARCf-f MOLDfNG
l Removal / Installation
13EOSX-310
S-6
BONNE
COMPOh
Rembvaf
1. Removi
2. lnstatl if

S
FRONT BUMPER FRONT BUMPER
COMPONENTS
Rem’ovat ! Installation
1. Removal in the order shown
2. Install in the reverse order of
1 in the figure.
removal.
-9-9.8 Nm 170-100 kgfem,
U-87 h.lbfJ
f4-m Ikgf-m, ft-lbf J
13EOSX-312
4. Front bumper
Disassembly / Assembly
. . . . . . . . . ..m... page S-9 1. Radiator grille
2. Front conbination light
3. Headlight
5-8
Disassembh
I . Disassemi
2. Assemble
t
1. Fog lights
-
a
-I. 2. Bumper rear
3. Bumper me

FRONT BUMPER S
Disassembly / Assembly
I. Disassemble in the order shown in the figure.
2. Assemble in the reverse order of disassembly.
i
1, Fog lights
2. Bumper reinforcement
3. Bumper mesh 4. Hook cover
5. Bumper fascia

S REAR SKIRT
REAR SKIRT -
COMPONENTS
Rembal / Installation
1. Remove in the order shown in the figure.
2. Install in the reverse order of removal.
Note
l Remove the rear bumper to remove and install the rear skirt.
1. Rear skit-! 2. Rear bumper
S-10 WHEEL,
COMPONE
Removal I
1. Remove i
2. Install in t
I, Front why
Removi
I nstallat

T ~WPe~MENTAL SERVICE INFORMATION, EXTERIOR LIGHTING SYSTEM
SUPPLEMENTAL SERVICE INFORMATION
The following points shown in this section are changed in comparison with 323 Workshop manual supple-
menP(1229-1 O-89t) and 323 Workshop manual supplement (1275-l O-91 C>.
Front fog light
l Removal I Installation
13EOTX-305
EXTERIOR LIGHTING SYSTEM
FRONT FOG LIGHT
Removat / tnstaitation
I. Remove in the order shown in the figure.
2. Install in the reverse order of removal.
I. Radiator grille
2. Front combination light
3. Headlight 4. Front bumper
5. Front fog light
T-4