fuel pressure MAZDA 323 1992 Workshop Manual Suplement

A PRE-DELIVERY INSPECTION TABLE
PRE-DELIVERY INSPECTION TABLE
[EXTERlORI
INSPECT and ADJUST, of necessary. the followlng Items to
specrfrcatron:
0 Glass, exterior bright metal and paint for damage
0 Wheel lug nuts
0 Tire pressures
0 All weatherstrips for damage or detachment
0 Operation of bonnet release and look
0 Operation of trunk Ild, hatch and fuel lbd opener
(of equipped)
0 Door operation and alignment
0 Headtrght aiming
INSTALL the foltowrng parts
0 Wheel caps or rrngs (if equipped)
0 Outsrde mirror(s)
1 UNDER BONNET-ENGINE OFF j
INSPECT and ADJUST. If necessary, the following items to
specrflcatlon.
0 Fuel, coolant and hydraulic tines, fittings, connectlons and
components for leaks
0 Engine 011 level
0 Power steering fluid level (of equipped)
0 Brake master cylinder fluky levels
0 Clutch master cylinder fturcl levels (If equipped)
0 Wtndshreld washer reservojr flurd level
0 Radiator coolant level and specrfic gravity
0 Tightness of water hose clamps
0 Tightness of battery terminals, electrolyte level and specific
gravity
0 Manual transaxle oil level
0 Drive belt(s) tension
Cl Carburetor lrnkage (choke control, wrde open throttle posi-
tion. etc ) (carburetor model only)
q Accelerator cable and linkage for free movement
0 Headlight cleaner and flurd level (if equipped)
BLEED air from fuel line (diesel engrne only)
CLEAN the spark plugs (except for diesel engine)
piEi6F]
INSTALL the following parts
0 Rubber stopper for rnsrde rear view mirror (if equjpped)
0 Fuse for accessories
CHECK the operation of the following items.
0 Seat controls (sliding and reclining) and head rest
0 Seat belts and warning system
Cl Ign&on switch and steering lock
0 Power window (if equipped)
D Door tacks including child proof door locks
Cl Inhibitor switch (ATX only)
Cl All Ikghts rncluding warning and Indicator lbghts
0 Ignition key reminder buzzer (If equipped)
A-Z
0 Horn, wbpers and washers (front and rear, If equipped)
0 Antenna (tf equipped)
0 Cigarette Ibghter and clock (if equipped)
0 Remote control outside mirror (if equrpped)
0 Heater, defogger and air conditioner at various mode selec-
tions (if equlppedj
0 Sunroof (If equipped)
CHECK the following items
0 Presence of spare fuse
0 Upholstery and Interior finish
CHECK and ADJUST, If necessary, the followjng items:
IJ Operation and fit of windows
0 Pedal height and free play of brake and clutch pedal
0 Parking brake UNDER BONNET-ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
0 Operation of Idle-up system for air condbtroner or power steer-
ing (if equrpped)
0 Automatic transaxle flurd levet
0 tnltial ignrtlon timing (except disel engine)
0 Idle speed
0 Operation of throttle positron. sensor (EGI engrne)
0 Operation of cold start device and glow plug warning light
(diesel engine only)
0 Operation of dash pbt (EGI.engine)
fTiGGJ
CHECK the following items.
0 Underside fuel, coolant and hydraulic Irnes, ftttlngs, connec-
tions and components for leaks
0 Trres for cuts or brurses
0 Steering Itnkage, suspensron, exhaust system and all under-
side hardware for .looseness or damage 1 ROAD TEST j
CHECK the following items
0 8rake operation
0 Clutch operation
0 Steering control
!ZI Operation of meters and gauges
Cl Squeaks, rattles or unusual noises
Cl Engine general performance
0 Emergency locking retractors 1 AFTER ROAD TEST ]
REMOVE the seat and floor mat protective covers
CHECK for the necessary owner information materials, took
and spare tire
m vehicle
93EOAX-002
-- MAIN Char3 t: In
A: PC R: F!t T: Ti! Emis! The ed : to t!

F3
c
FUEL AND EMISSION
CONTROL
SYSTEMS
i
INDEX . . . . . . . . l ..,.... *..,. . . . . . . m...*.*...*..... F3- 2
UUTLtNE
...................................... F3- 4
OUTLINE OF CONSTRUCTION.. ....
F3- 4
SYSTEM DIAGRAM ...................... F3- 5
VACUUM HOSE ROUTING
DIAGRAM
................................. F3- 6
WIRING DIAGRAM.. .....................
F3- 7
ECU RELATIONSHIP DIAGRAM ...... F3- 8
SPECIFICATIONS.. ....................... F3- 9
TURBOCHARGER CONTROL .......... F3-IO
OUTLINE
.................................... F3-10
SYSTEM DIAGRAM ...................... F3-10
WASTEGATE CONTROL ............... F3-11
FUEL SYSTEM
.............................. F3-12
OUTLINE ....................................
F3-12
CONTROL SYSTEM .......................
F3-13
STRUCTURAL VIEW .....................
F3-13
PRESSURE REGULATOR
CONTROL SYSTEM ....................
F3-14 SUPPLEMENTAL SERVICE
tNFOF?MATtON
............................. F3-I 5
SELF-DtAGNOStS FUNCTtON.. ........
F3-16
OUTLINE ....................................
F3-16
SERVICE CODE NUMBERS..
......... F3-16
TROU8LESHOOTtNG GUtDE
........... F3-19
RELATIONSHtP
CHART.. F3-19 ..............
DIAGNOSTIC JNDEX
.................... F3-20
PRECAUTIONS
............................
F3-21
SYMPTOM TROUBLESHOOTING .... F3-22
TURBOCHARGERCONTROL
SYSTEM ......................................
F3-37
TURBOCHARGER F3-37 ........................
WASTEGATE SOLENOID VALVE.. .. F3-38
INTERCOOLER ............................
F3-39
FUELSYSTEM ..............................
F3-40
FUEL PUMP ................................
F3-40
FUEL PUMP RESISTOR/RELAY ......
F3-40
PRESSURE
REGULATOR .............. F3-41
INJECTOR ..................................
F3-42
INJECTOR RESISTOR
................... F3-42
PRESSUR REGULATOR CONTROL
SYSTEM ......................................
F3-43
SOLENOID VALVE (PRESSURE
REGULATOR CONTROL)
............. F3-43
CONTROL SYSTEM
....................... F3-44
PREPARATION ............................ F3-44
ENGINE CONTROL UNIT (ECU) ..... F3-45
7 3EOF3-301

INDEX F3
t
3EOf3.303
1. Injector 4. Solenoid valve (PRC high temp.)
Inspection ................................. page F3-42 Inspection ;. ............................... page F3-43
Volume test.; ............................. page F3-42 5. Fuel pump resistor/relay
2. Pressure regulator System operation ...................... page F3-40
Inspection ................................. page F3-4 1 Inspection ....... . .........................
page F3-4 1
II
3. Solenoid valve (PRC low temp.) 6. Fuel pump (main)
Inspection ................................. page F3-43 Inspection .......... . ...................... page F3-40

F3 OUTLINE
OUTLINE
OUTLINE OF CONSTRUCTION
Theefuel and emission control system of the new 323 4WD model 1s basically the same as that of the prevr-
ous 323 4WD model; however some parts are changed. The changed parts and interchangable parts
are shown betow.
13EOF3-304
Changed parts
1 ~ components Contents and purpose Reference pagl
INTAKE AlR
SYSTEM Turbocharger
Intercooler
l Size Increased for greater boost pressure l Wastegate solenord valve IS lozated on Intake port of F3-10
turbocharger to make system more compact F3-37
Volume increased for Improved F3-10
t F3-39
Wastegate sojenold valve
l Wastegate solenoid valve changed to duty solenoid
type for Increased engine power and response
l Wastegate solenoid valve is located on Intake port of
turbocharger to make system more compact F3-1 f
F3-38
I r
Pressure regulator One-stage operattlon changed to two-stage operatron F3-14
to improve hot restarting f3-41
L
FUEL SYSTEM High-ohmic type change to low-ohmrc type with exter-
Fuel qector na solenoid reslstor for improved fuel supply during F3-12
high-speed driving F3-42
Fuel pump reslstor Resistance reduced for
surer fuel supply F3-40
CONTROL
SYSTEM Pressure
regulator control system
Atr flow meter Two-stage operatton used to Improve hot restarting
Measures larger amount of air flow Increased power
Resistance values changed F3-t4
F3-43
F3- 9
f3EOF3-305 lnterchangable parts
tntake air system
l
Air valve
l Air bypass valve
l Air cleaner
l Air cleaner element
Fuel system
l Fuel filter assembly
l Fuel pu.mp (transfer
l Fuel vapor valve Control system
. l Throttle sensor
l Water thermosensor
l Knock sensor and control unit
l Oxygen sensor
l Fuel pump control unit
l Main relay
l Circuit opening relay
l Check valve (two-way) .
Evaporative system
l Charcoal canister
l Check valve (two-way)
13EOF3-306
F3-4

F3 OIJTUNE
SPE
* TEN
The @
ECU RELATtONSHtP DtAGRAM
1NPUT DEVICE
KNOCK SENSOR
c AIRFLOW METER
KNOCK
DlSTRlBUTOR
91c YfTC”
THERMOSENSOR
OXYGENSENSOR N EUTRAti
CLUTCH SWITCH
CONNECTOR
(TEN TERMINAL,)
INTAKE AIR
OUTPUT
DEVtCE THERMOSENSOR
{AIRFLOW METER)
CIRCUIT
OPENING
TURBOCHARGE
jAGNOSE
ONNECTOR
EN/MEN TERMINA
h SOLENOID VALVE
(PRESSURE REGUL+TOR
CONTROL)
WASTEGATE
SOLENOID VALVE IGNITER
- - (TURBtiHARGER)
FUEL PUMP
RESlSTORlRELAY
SOLENOID VALVE
(PURGE CONTROL)
F3-8 13EOF3-311

OUTLINE F3
SPEClFiCATlONS
Iten
Idle speed’
tgnltion trming * Engine
m
BTDC BP TURBO
800 f 50
IO f 10
Fuel pump
Maximum output pressure kPa { kgflcm’, psi 1 1 490-736 {SO-7.5, 7t-110)
Transfer pump
Maximum output pressure
Fuel filter kPa { kgf/cm2, psi ) 1 , 39 10.4, 5.7 1 or higher
Nylon element (in fuel pump)
Idle-speed control (fSC) valve
Type
Resistance I Rotary
nt
11-13 [at 2O*C [68*F)]
Solenoid va tve (purge contra I)
,I
Resistance -2o*c I -4Of 1 14.6-I 7.8
2.21-2.69
.kQ , 2o”c { 68OF)
40% f104*f 1 1.0-l .3
Resistance
Fuel tank
Capacity
Air cleaner
Etement type
Fuel
Specification L {US gal, Imp gal) [ Approx. 6 [at 20°C f 68*FJ]
60 (15.9, 13.2)
01 permeated
Unleaded premium (RON 95 or higher)
11FrlC?.7 11
l TEN terminal of diagnosis connector grounded.
The I; mark indicates newly equipped Parts. l”L”l “VI I
F3-9

F3 FUEL SYSTEM
FUEL
SYSTEM
OUTLINE
l Thspressure regulator has two vacuum ports for its two-stage operation. (Refer to page F3-43.)
l The injectors are changed from high-ohmic type to low-ohmic type for improvement of the supply of fuel
during high-speed engine operation.
l To decrease the current in the injectors, an external resistor is equipped and is mounted on the aircleaner
housrng .
13EOF3315 Pressur regulator
VACUUM PORTS
F3-12 13EOF331;

:
:
1 , ._.s_ , -. _ ._>_ ‘r--A.-
_, . :. . . . . .-
CONTROL SYSTEM F3
CONTROL SYSTEM
STRUCTURAL VtEW
SOLENOID VALVE
PRESSURE RE
LUTCH SWlTCH
FUEL INJ RELAY
NTAKE AIR THERMOSENSOR
AIRFLOW METER)
WATER THERMOSENSOR
F3-13

F3 CONTROL SYSTEM
PRESSURE REGULATOR CONTROL SYSTEM
SOLENOID VALVE TO MAIN RELAY
(PRC HIGH TEYP.)
t ECU
I
PRESSURE REGULATOR
// VACUUM

IJ WATER
THERMOSENSOR
F----------- lNTAKE AIR
THERMOSENSOR
SWITCH SOLEltolD VALVE
(PRC LOW TEMP.)
TO FUEL TANK
13EOF3-31 To prevent vaporlock in the fuel system during hot restart idle, a two-stage pressure regulator is adoped
to the new 323 4WD.
Low temperature operation: The vacuum to the pressure regulator (A and B ports) is cut (solenoid valve
[low temp.] UN), and the fuel injection pressure is increased to 284 kPa (2.90 kgf/cm2, 41 psi ) ,
High temperature operation: The vacuum to the pressure regulator (A port) is cut (solenoid valve [high
temp.] ON), and the fuel injection pressure is increased to 343 kPa [ 3.5 kgf/cm2, 49 psi 1.
Condition and operation
Condition Operation
1
coolant Intake alt Solenoid vrlve Solenoid vatve Opemtlon
I temperature temperature Engine (Idw temp.)
(high temp.) time Operation 40% [fU40f)-
Above 90°C 5U°C (t22OFI ON OFF 180s Low temp.
f f940Fj No load
Above 5O*C
I122OF) OFF ON 210s t-ltgh temp.
3
t3EOF3-319
F3-14 Wast
l Ins fuel
l In:; InJeci
l In:;
l Vol Injecl
l In:;
Presr
l SCI Engir
l InsI

SUPPLEMENTAL SERVICE INFORMATION .
I
The following points in this section are changed in comparison to the Mazda 323 4-Wheel Drive Work-
shop Manual [I 229-l O-89t].
Turbocharger
l Removal / Installation
Wastegate solenoid valve
l Inspection
htercooter
l Removal I Installation
Fuel pump (main)
l Inspection
Fuel pump resistor/relay
l System operation
l Inspection
Injector
l Inspection
l Volume test
Injector resistor
l Inspection
Pressure regulator control system
l Solenoid valve (pressure regulator control}
Engine control unit (ECU)
l Inspection 13EOF3.320
F3-I 5