tow MAZDA 323 1992 Workshop Manual Suplement

c
>
3
3
Gf
m
GENERAL INFORMATION
1MPORTANT INFORMATION
..................... GI- 2
BASIC ASSUMPTIONS ............................ a- 2 I
SAFETY RISK
........................................ Gl- 2
POSSIBLE LOSS OF WARRANTY
............. Gl- 2
WARNING ON LUBRICANTS
AND GREASES
.................................... GI- 2
HOW TO USE THIS MANUAL..
.................. GI- 3
PREPARATION
...................................... GI- 3
REPAtR PROCEDURE .............................
GI- 3
SYMBOLS .............................................
GI- 4
NOTES, CAUTIONS, AND WARNINGS.. .....
Gl- 4
FUNDAMENTAL PROCEDURES
................. GI- 4
PROTECTION OF THE VEHICLE .............. G1- 4
A WORD ABOUT SAFE-T-Y
....................... Gl- 5
PREPARATION OF TOOLS
AND MEASURING EQUIPMENT ............. Gi- 5
SPECIAL TOOLS ....................................
GI- 5
REMOVAL OF PARTS .............................
GI- 5
DISASSEMBLY ......................................
GI- 5
REASSEMBLY
....................................... GI- 6
ADJUSTMENTS .....................................
Gl- 7
RUBBER PARTS AND TUBtNG ................ GI- 7
JACK AND SAFETY STAND POStTlONS .... GI- 8
VEHICLE LIFT (20SUPPORT TYPE)
POSITIONS ............................................
GI- 6
MAINTENANCE NOTE ..............................
GI- 9
SPEEDOMETER TESTER CHECK
............. GI- 9
BRAKE TESTER CHECK
......................... GI- 9
CHASSIS DYNAMOMETER CHECK.. ......... Gl-I 0
WHEEL BALANCE.R ...............................
GI-I 0
TOWtNG ...............................................
GI-I 0
IDENTlFiCATlON NUMBER LOCATIONS
..... GI-I
2 .UNlTS .....................................................
GI-I 2
ABBREVIATIONS
.....................................
GI-12
CAUTION
................................................ GI-13
INSTALLATlON OF MOBILE TWO-WAY
RADIO SYSTEM ...................................
Gl-13
PRECAUTIONS TO TAKE WHEN
SERVICING AN ELECTRICAL SYSTEM ..i GI-f4
HANDLING CONNECTORS ..................... GI-f 5
USING ELECTRICAL
MEASURlNG EQUIPMENT ........................................
GI-16
13EGIX-30 1

MAlNTENANCE NOTE GI
.
FREE ROLLER
I t 3EGlX-304
MAlNTENANCE NOTE
SPEEDOMETER TESTER CHECK
Caution
l Do not clutch abruptly.
l Do not attempt rabbit starts or accelerate quickly. 13EGIX-302
[Front wheel free-roller method]
1. Set the free roller securely on the floor under the front wheels
by matching it to the wheel base and front tread.
2. Place the vehicle softly on the tester and free roller.
3. Start the engine, and engage the clutch softly at a low speed
in 2nd gear; then gradually increase the speed.
4. Upon completion of the test, stop the engine by gradually
decelerating with soft braking.
[Front wheel jack-up method1
1’. Place the rear wheels on the roller.
2. Jack up the front wheels and mount on a safety stand.
3. Start the engine, and engage the clutch softly at a low speed
in 2nd gear; then gradually increase the speed.
Caution
l When using either the front wheel free-roller meth-
od or front wheel jack-up method, secure the vehi-
cle to prevent forward and lateral movement by
attaching towing hardware (chain or wire) to the
front and rear tow hook or tie-down hook.
BRAKE TESTER CHECK
Caution
. To stabilize the drag force of the viscous coupling,
conduct the brake test after the speedometer test.
1. Place the wheels to be tested (front or rear) on the roller.
2. Shift itit0 NEUTRAL.
3. Drive the tester roller and check.
a-9

MAINTENANCE NOTE
TOWlNG
Caution
g Use method @I to tow vehicles having problems in the steering system or drivetrain.
Towing method
0 Rope towing items to confirm
Parking brake Transaxle shtft posttton Remarks
Released Neutral
@ Towlng with front wheels off
ground
Released Neutral Remove propeller shaft
@ Towtng by wrecker truck
Released Neutral
Rempve propetler shaft
@Towing or hauling with all wheels
off ground
Engaged Any posItIon
13EGIX.30
TIE-DOWN HOOKS - FRONT TIE-DOWN HOOKS
- REAR (HATCHBACK)
!

A PRE-DELIVERY INSPECTION TABLE
PRE-DELIVERY INSPECTION TABLE
[EXTERlORI
INSPECT and ADJUST, of necessary. the followlng Items to
specrfrcatron:
0 Glass, exterior bright metal and paint for damage
0 Wheel lug nuts
0 Tire pressures
0 All weatherstrips for damage or detachment
0 Operation of bonnet release and look
0 Operation of trunk Ild, hatch and fuel lbd opener
(of equipped)
0 Door operation and alignment
0 Headtrght aiming
INSTALL the foltowrng parts
0 Wheel caps or rrngs (if equipped)
0 Outsrde mirror(s)
1 UNDER BONNET-ENGINE OFF j
INSPECT and ADJUST. If necessary, the following items to
specrflcatlon.
0 Fuel, coolant and hydraulic tines, fittings, connectlons and
components for leaks
0 Engine 011 level
0 Power steering fluid level (of equipped)
0 Brake master cylinder fluky levels
0 Clutch master cylinder fturcl levels (If equipped)
0 Wtndshreld washer reservojr flurd level
0 Radiator coolant level and specrfic gravity
0 Tightness of water hose clamps
0 Tightness of battery terminals, electrolyte level and specific
gravity
0 Manual transaxle oil level
0 Drive belt(s) tension
Cl Carburetor lrnkage (choke control, wrde open throttle posi-
tion. etc ) (carburetor model only)
q Accelerator cable and linkage for free movement
0 Headlight cleaner and flurd level (if equipped)
BLEED air from fuel line (diesel engrne only)
CLEAN the spark plugs (except for diesel engine)
piEi6F]
INSTALL the following parts
0 Rubber stopper for rnsrde rear view mirror (if equjpped)
0 Fuse for accessories
CHECK the operation of the following items.
0 Seat controls (sliding and reclining) and head rest
0 Seat belts and warning system
Cl Ign&on switch and steering lock
0 Power window (if equipped)
D Door tacks including child proof door locks
Cl Inhibitor switch (ATX only)
Cl All Ikghts rncluding warning and Indicator lbghts
0 Ignition key reminder buzzer (If equipped)
A-Z
0 Horn, wbpers and washers (front and rear, If equipped)
0 Antenna (tf equipped)
0 Cigarette Ibghter and clock (if equipped)
0 Remote control outside mirror (if equrpped)
0 Heater, defogger and air conditioner at various mode selec-
tions (if equlppedj
0 Sunroof (If equipped)
CHECK the following items
0 Presence of spare fuse
0 Upholstery and Interior finish
CHECK and ADJUST, If necessary, the followjng items:
IJ Operation and fit of windows
0 Pedal height and free play of brake and clutch pedal
0 Parking brake UNDER BONNET-ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
0 Operation of Idle-up system for air condbtroner or power steer-
ing (if equrpped)
0 Automatic transaxle flurd levet
0 tnltial ignrtlon timing (except disel engine)
0 Idle speed
0 Operation of throttle positron. sensor (EGI engrne)
0 Operation of cold start device and glow plug warning light
(diesel engine only)
0 Operation of dash pbt (EGI.engine)
fTiGGJ
CHECK the following items.
0 Underside fuel, coolant and hydraulic Irnes, ftttlngs, connec-
tions and components for leaks
0 Trres for cuts or brurses
0 Steering Itnkage, suspensron, exhaust system and all under-
side hardware for .looseness or damage 1 ROAD TEST j
CHECK the following items
0 8rake operation
0 Clutch operation
0 Steering control
!ZI Operation of meters and gauges
Cl Squeaks, rattles or unusual noises
Cl Engine general performance
0 Emergency locking retractors 1 AFTER ROAD TEST ]
REMOVE the seat and floor mat protective covers
CHECK for the necessary owner information materials, took
and spare tire
m vehicle
93EOAX-002
-- MAIN Char3 t: In
A: PC R: F!t T: Ti! Emis! The ed : to t!

F3 OUTLINE
OUTLINE
OUTLINE OF CONSTRUCTION
Theefuel and emission control system of the new 323 4WD model 1s basically the same as that of the prevr-
ous 323 4WD model; however some parts are changed. The changed parts and interchangable parts
are shown betow.
13EOF3-304
Changed parts
1 ~ components Contents and purpose Reference pagl
INTAKE AlR
SYSTEM Turbocharger
Intercooler
l Size Increased for greater boost pressure l Wastegate solenord valve IS lozated on Intake port of F3-10
turbocharger to make system more compact F3-37
Volume increased for Improved F3-10
t F3-39
Wastegate sojenold valve
l Wastegate solenoid valve changed to duty solenoid
type for Increased engine power and response
l Wastegate solenoid valve is located on Intake port of
turbocharger to make system more compact F3-1 f
F3-38
I r
Pressure regulator One-stage operattlon changed to two-stage operatron F3-14
to improve hot restarting f3-41
L
FUEL SYSTEM High-ohmic type change to low-ohmrc type with exter-
Fuel qector na solenoid reslstor for improved fuel supply during F3-12
high-speed driving F3-42
Fuel pump reslstor Resistance reduced for
surer fuel supply F3-40
CONTROL
SYSTEM Pressure
regulator control system
Atr flow meter Two-stage operatton used to Improve hot restarting
Measures larger amount of air flow Increased power
Resistance values changed F3-t4
F3-43
F3- 9
f3EOF3-305 lnterchangable parts
tntake air system
l
Air valve
l Air bypass valve
l Air cleaner
l Air cleaner element
Fuel system
l Fuel filter assembly
l Fuel pu.mp (transfer
l Fuel vapor valve Control system
. l Throttle sensor
l Water thermosensor
l Knock sensor and control unit
l Oxygen sensor
l Fuel pump control unit
l Main relay
l Circuit opening relay
l Check valve (two-way) .
Evaporative system
l Charcoal canister
l Check valve (two-way)
13EOF3-306
F3-4

F3 SELF-DIAGNOSIS FUNCTION
:ODE NO. 25 {SOLENOlD VALVE - PRESSURE REGULATOR CONTROL) (Low temperature opoeration)
INSPECTION ACTION
Disconnect connector from ECU; IS there battery Yes Check ECU termrnal connector for poor
voltage at ECU terminal 2T (G/C) wrth Ignition connection
switch ON?
4 If OK, replace ECU
CT page F3-2
c3 If not OK, repatr or replace connector
NO Go to next step
2 In same condition as rn Step 1. is there battery Yes Repair or replace wlrrng harness (G/O)
voltage at sofenord vatve (PRC low temp.) con-
nector termrnal wrre (G/O)?
NO Go to next step
3 Is solenord valve (PRC low temp ) UK7 Yes Check for a short or open crrcuit in WII-
CT page F343 ing harness (main relay [FUEL INJ re-
lay] - solenoid valve [PRC low temp.])
NO Replace solenord valve (PRC tow temp.)
1
t3EOF3-323
CODE NO. 35 (SOLENOID VALVE - PRESSURE REGULATOR CONTROL) (High temperature opoeration)
STEP lNSPECTlON ACTlON
1 Disconnect connector from ECU: is there battery Yes Check ECU terminal connector for poor
voltage a? ECU terminal 22 (G) with rgnttlon connection
swttch ON7
4 If OK, replace ECU
J page F3-2
e If not OK, repair or replace connector
No Go to next step
2 In same condrtron as In Step 1, is there battery Yes
voltage at solenoid valve (PRC high temp.) con- Repair or replace wiring harness (G)
nector terminal wire (G)?
No Go to next step
3 Is solenoid valve (PRC high temp ) OK7 Yes Check for a short or open circuit In wir-
r;r page F343 ing harness (marn relay [FUEL INJ re-
WI - sofenord valve [PRC high temp.])
No Replace solenoid valve
(PRC high temp.)
f3EOF3-324
Circuit Diagram
ECU
I
2T 22 I
G
TO MAIN RELAY
I SOLENOID
VALVE
(PRC HIGH TEMP.)
F3-18 :3EOf3 32 5
--
TRW
RELAT
c
-..


INPUT
--
KNOCH
--
DIAGM
(TEN T
--
IGNITIi
(STAR1
--
E/L SIC
-a
P/S PR
--
A/c SYI
--
NEUTR
SWITCI
--
STUPb
--
ATMDI
SENSQ
-a
THRUI
-..
INfAk.1
--
AlFlFLC
--
UXYGE
--
WATEF
--
DlSfRl

TROUBLESHOOTING GUiDE F3
15 ENGINE STALLS ON DECELERATION
IESCRIP-
l Engrne unexpectedly stops running dunng or after deceleration
[iON l Idle condition normal.
TROUBLESHOOT1NG HtNTS]
ingrne speed drops too much when releasrng accelerator
3 Idle-speed misadjustment @I Loose connector disconnected by force of deceleration
3 Fuel-cut contrd malfunction
TEP lNSPECTlON ACTION
1 1s idle condition normal? Yes Go to next step
tdle speed: 800 f 50 rpm (in neutral)
NO Adjust or perform Troubleshooting, Nos.
8-I 1 “ROUGH IDLE”
(Refer to Workshop Manual
(1203-I o-89F))
2 Is “00” displayed on Self-Diagnosis Checker Yes Go to next step
with ignition switch ON?
SYSTEM SELECT: 1 NO Service Code No. displayed
Check for cause (Refer to specified
check sequence) ET page F3-16
“88” flashes
Check ECU termrnal 1 F voltage
Voltage: Battery voltage
(ignition switch ON) r;r page F346
W:SELFTEST
e If OK, replace ECU CI page F3-3
4 If not OK, check wirtng
(ECU - Self-Diagnosis Checker)
3 Does Self-Diagnosis Checker Monitor Lamp with Yes Go to next step
lgnttlon switch UN show that switches operate
correctly?
NO Lamp not ON or OFF with specified
switch
Check for cause (Refer to specified
check sequence)
W: SEtF TEST Lamp slways ON
Check wiring between
(ECU terminal 1 D - Self-Diagnosis
Checker)
4 Are ECU ?erminal voltages OK? Yes Go to next step
(especially IV, 20, 20, ZU, 2V.
and 20) v page F346 No
Check for cause
5 Check for poor connection of foltowing parts YC?S Repair or replace
l ignrtion coil l Igniter l Olstribdor l High-tension lead
NO Go to next step l Injector. l Injector resistor l Ctrcuit-opening relay . l ECU
F3-35

F3 CONTROL SYSTEM
Terminal voltage
Reference date
Vs: Battery voltage
‘em&al Input Output Connected to Test condition Correct voltage Remark
1A - - Battery Constant VB
For backup
18 0 Main relay
Ignition switch OFF ov
(FUEL INJ relay) -
ON
V8
1C 0 lgnitlon switch While cranking Approx. 1 OV
(START) -
Ignition switch ON ov
10 0 Self-Diagnosis Test switch at SELF TEST
Wtth Self-
Checker Lamp illuminated for 3 sec. after ignition Approx. 5V
(monitor lamp) switch OFFdON Diagnosis Check-
er and System
lamp not iltuminated after 3 sec. V8 Selector
Test switch at 02 MONITOR with engine
idling Approx. 5V
Monitor lamp illuminated
Test switch at 02 MONITOR with engine
idling Vi3
Monitor lamp not illuminated
IE - - - - - -
IF
0 Self-Diagnosis Buzzer sounded for 3 sec. after ignition
Below 2SV
l With Seif-
Checker switch OFF-+ON
Diagnosis
(service code)
Buzzer not sounded after 3 set V0 ’ Checker and
Buzzer sounded Below 2.5V System Selector
l With System
Buzzer not sounded VB Selector test
switch at SELF
TEST
1G 0 igniter tgnition switch ON
ov
-
Idte
Approx. 0.2V
It-l 0
Solenoid valve Ignition switch ON
VB
(wastegate)
Idle
Approx. 2V ’ -
II
0 Fuel pump While cranking
Approx. 1 OV
resistor/relay -
Idle
8etow 1.5V
IJ 0 NC relay Ignition switch ON
VB
A/C switch UN at idle
Below 2.5V
. NC switch OFF at idle V3
-
IK 0 Diagnosis
connector
(TEN terminal) System Selector test switch at
02 MONITOR
System Selector test switch at
SELF TEST V0
-
8elow l*OV
1L - - - - - -
I
1M - - - - -
I -
lr ‘- l-7
f L.-
r
20 20 2M 2K 21 2G 2E 2c 2A IU 1S 10 10 ltvl tK II Ir; tE 1~ IA
1
22 2x 2v 2T ZR 2P 2N 2L 25 2H 2F 20 2B 1V IT 1R tP 1N IL 1J 1H IF 1~ 1~
1
J=3-46 --
4lways 4
--
AIways 4
--
Atways 1
--
Always 1
-a
Always ’
--
Always i
-e
Always I
2.5v
Always
Always (
-m
Always f
-a
Always 1
Always (
--
Always I
2.5V
Always 1
Always t
Always
--

-. _.. . . . . . _ - ._.
-w
CONTROL SYSTEM F3
I .
-.
Ve: Battery voltaae I
Incorrect voltage
Atwafi below 1 .OV
Always VB
Always VS (foglight switch OK)
Always below 1 .OV
Always below 1 .OV
Always Vs
Always
below 23 (blower fan OK)
Always VB (blower fan OK)
Always below 1 .OV
(electric cooling fan OK) -
1-
Possible cause
l Throttle sensor mrsadjustment l Short circuit in wtrrng from throttle sensor to ECU terminal 1 N l ECU malfunction
l Throttle sensor mrsadjustment l Open circuit in wiring from throttle sensor to ECU terminal fN l Open circuit in mnng from throttle sensor to ECU terminal 20
l Foglight relay malfunctron
l Foglrght relay malfunction
l P/S pressure switch maltunctron l Short crrcurt In wrrlng from P/S pressure switch to ECU terminal 1 P l ECU malfunction
l P/S pressure switch malfunction l Open circuit in wlnng from P/S pressure switch to ECU terminal 7 P l Open circuit in wiring from P/S pressure switch to ground
l A/C switch malfunctron l Short circuit tn wiring from A/C switch to ECU terminal 1Q l Poor connection at ECU connector l ECU malfunction
l #C swatch malfunction l Open circuit in wiring from A/C switch to ECU terminal 1Q l Open circuit in wiring from A/C switch to blower control switch
l Open or short circuit in wiring from fan relay to ECU terminal 1R l ECU matfunction
Always below 1 .OV (blower fan OK}
Always Vs (btower fan OK)
Always betow illumination lamp
1 .ov ON when rear
window defroster
switch ON
Illumination lamp
never ON
Atways below 1 .OV (headttghts OK)
l Short circuit in wrrtng from blower control switch to ECU terminal IS l Poor connection at ECU connector l ECU m&function
l Open crrcuit in wrrrng from blower control switch to ECU terminal 1s
l Open or short crrcuit In wiring from rear window defroster switch to ECU
terminal t T
l Open circuit in wiring from ignitron switch to rear window defroster switch l Rear window defroster switch malfunction
l Open or short circuit in wiring from headlight relay to ECU terminal 1 U
Always below 1 .OV
l Neutral switch malfunction l Clutch switch malfunction l Short circuit in wiring from ECU terminal IV to neutral or clutch switch
Always VB
l Neutral switch malfunction l Clutch switch malfunction l Open circuit in wiring from ECU terminal 1V to neutral or clutch swdch l Poor connection at ECU connector
13FOl=3-36 .
F3-49
.:i

NARNESS SYMBOL : z (FJ m (E) a (I) m (R) *(OFI)- (IN) ‘*t (FFi)* (EM)= (INJ)
F-2 1
/ E-12
FUSE BOX
MA,N FUSE IGNITION
SWITCH
CONNECTOR
/ / F-07 STOWGHT
LH
JOINT BOX