wheel bolt torque MAZDA 323 1992 Workshop Manual Suplement

M FRONT AXLE
WHEEL HUB, STEERING KNUCKLE
RemovaI / Inspection I Installation
1. Remove in the order shown in the figure, referring to Removal Note.
2. Inspect all parts and repair or replace as necessary.
3. InstaH in the reverse order of removal, referring to Installation Note.
Caution
l Loosely tighten the shock absorber bolts. Lower the vehicle and tighten the bolts to the specified
torque with the vehicle unladen.
4. Adjust the front wheel alianment.
16-22 ]1.6-2.3, 12-161 I
19.0-l 2.0, 65-86.7 I
1. Wheel hub nut
2. Wheel and tire
3. Locknut
Removal Note . . . . . . .._.. . . . . . . . . . . . . . . . . . . . page M-7
installation Note .I.........,..,............ page M-7
4. Brake caliper assembly
Service . _. . . . . . . . . ,__. . . , , . ._. _. , , . . . , . ._ ._. . . . . . Section P
5. Disc plate
lnspectioti .~~*.......*~...,......,,,.....*~...~. Section P
6. ABS wheel speed sensor (if equipped)
7. Tie rod end
Removal Note . . . . . . .._.......... I . .._.....= page M-7
lnstallatiofi Note . . .._... _.__......,....... page M-7
M-6
8. Lower ball joint
9. Steering knuckle, wheel hub, and dust cover
Inspect-wheel hub for cracks and damage
Inspect knuckle spindle for cracks and
damage
Inspect dust cuver for damage and dis-
tortion
Disassembly I Inspection I
Assembly . ..C1..............~...,.....,.....
page M-8

REAR AXLE
WHEEL HUB, KNUCKLE
Removal I Inspection / installation
1. Remove in the order shown in the figure, referring to
Removal Note. 2. Inspect all parts and repair or replace as necessary.
3. Install in the reverse order of removal, referring to Installation Note.
Caution
l Loosely tighten the shock absorber bolts. Lower the vehicle and tighten the bolts to the specified
torque with the vehicle unladen.
4. Adiust the rear wheel alianment.
16-22 1?.6-2.3, 12-16 I
7
IO.o-13.0,
66-66.7 1 1. Wheel and tire
2. Locknut
Removal Note..; . . . . . . . . , . . . . ,.......- -.. page M-f 3
Installation Note .._...,.,...._.__........ page M-13
I$ Brake caliper assembly
Service . . . . . . . . . . . ..e......._......... ,.,...,....
Section P
4. Disc plate
‘Service ..I....................__....... . . . . . . . . . Section P 5. Af3S wheel speed sensor (if equipped)
6. Wheel hub, knuckle
Disassembly I Inspect& /
Assem bty . . . . . . . ..I..........*..*.*...-... page M-14
Inspect wheel hub and knuckle for damage
or cracks
Inspect dust cover for damage or defor-
mation
M-12

TD
TECHNICAL DATA
ENGtNE ..................................................
TD- 2
LUBRICATlON SYSTEM ...........................
TD- 4
COOLING SYSTEM ..................................
TD- 5
FUEt AND EMISSION CONTROL
SYSTEMS
.............................................
TD- 6
ENGINE ELECTRICAL SYSTEM
................ TD- 7
CLUTCH .................................................
TD- 7
MANUAL TRANSAXLE AND TRANSFER
.... TD- 8
PROPELLER SHAFT
................................
TD-l 0
FRONT AND
REAR AXLES ....................... TD-lU
STEERING SYSTEM ................................
TD-11
BRAKING SYSTEM
..................................
TD-11
WHEELS AND TIRES
...............................
TD-12
SUSPENSION
......................................... TD-13
BODY ELECTRICAL SYSTEM
................... TD-14
STANDARD BOLT AND NUT TIGHTENING.
TORQUE ..............................................
TD-f 4
13ETOX-301
I
m I